May I "wax philosophical" here?
Switching supplies:
1. Efficient...very low heat generation, and hence little amounts of
"input" power being turned into waste.
2. A "switcher" MUST use some sort of oscillator to "do the magic". In
audio applications, we hope that switching frequency is FAR above the
audible range...such as 100 kHz, so minimal "pollution" in the audible
range.
3. However, if a given audio system has multiple "switchers", and each
is operating close to the same frequency, then you end up with
"hetrodynes". Example: in theory, one "switcher" operates at 100 kHz,
and a nearby "switcher" operates at 90 kHz. A POSSIBLE difference
exists at 10 kHz! It would be a "whistle" sound....
I dunno if anyone here ever plays with AM radio, or shortwave radio, BUT
there is so much SCHMUTZ (aka...interference...) on all bands now.
Switchers!!!!!
Linear power supplies:
1. Much more heat. The underlying concept is about as "green" as
setting clothes irons on the ironing board! lol "Waste Heat" makes it
all work.
2. Essentially NO noise besides the inherent 60/50 Hz harmonics. OK
OK...maybe harmonics at 120/180/240....etc Hz series.
Reliability.
Switchers are inherently unreliable, and I speak from many years of
experience.
The circuits are very complicated. The manufacturers use the cheapest
parts. The idea is disposable...
Analog Stuff tends to last longer...as in LM-317 etc.
IMHO.
Bri
Brian Gibson wrote:
Hi,
I think the voltage regulator number you are trying to remember is TL783.
Max input voltage up to 150V and output 125V max. at 700mA
Regards,
Brian G.
----- Original Message -----
*From:* eliya gwetta <mailto:[email protected]>
*To:* [email protected] <mailto:[email protected]>
*Sent:* Saturday, July 04, 2009 10:37 PM
*Subject:* Re: NEOTEK: Power for Series IIIc Pre's
Hi Matt,
Yes! I remembered the LM317 not being the right regulator for 48V, a
TL583 would be a drop in replacement or I would have to change other
components in the circuit as well?
On Sat, Jul 4, 2009 at 9:25 PM, Matt Syson
<[email protected] <mailto:[email protected]>>
wrote:
Hi
The JLM circuits are pretty much what you need so you could
either 'copy' the circuit and build it yourself or buy the kit.
I am not too impressed at using a LM317 for the phantom 48 rail,
they are only rated to 39 or 40 volt DIFFERENTIAL (input pin to
output pin) , meaning that if you short the output you stand a
good chance of 'blowing it up'. I presume the 47 Ohm resistor is
a lame way of trying not to 'kill' it, hardly a good engineering
solution.
You should substitute it for a TL583 (sorry this number won't
come to me, but there is a similarly packaged regulator that
handles 125 Volts).
Matt S
Donald Put wrote:
If you're up to making your own, there are numerous
PCBs/kits available for this type of project. They're set
up for dual voltages and 48VDC for the phantom power. Check
out JLM's offerings on his website:
http://www.jlmaudio.com/JLM%20Power%20Supply.htm
Cheers,
--
Don
------
View the list online at:
http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to
mailto:[email protected] <mailto:[email protected]>
with "unsubscribe neotek" in the message body. If you have any
difficulties, or questions --please send an email to
mailto:[email protected] <mailto:[email protected]>.
The Neotek list is lovingly hosted by Catapult Web. Remember
that any message or reply sent to the list will be automatically
forwarded to all subscribers.
Vive Le Neotek!
Thanks.
__________ Information from ESET NOD32 Antivirus, version of virus
signature database 4219 (20090705) __________
The message was checked by ESET NOD32 Antivirus.
http://www.eset.com
------------------------------------------------------------------------
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.375 / Virus Database: 270.13.5/2220 - Release Date: 07/05/09 17:54:00
------
View the list online at: http://www.mail-archive.com/[email protected]
You can unsubscribe at anytime by sending an email to mailto:[email protected] with
"unsubscribe neotek" in the message body. If you have any difficulties, or
questions --please send an email to mailto:[email protected].
The Neotek list is lovingly hosted by Catapult Web. Remember that any message
or reply sent to the list will be automatically forwarded to all subscribers.
Vive Le Neotek!
Thanks.
