Thank a lot for your reply. Like I said. I tried to run nm-applet by myself but still doesn't work and shown the following message:
NetworkManager: <info> starting... NetworkManager: <info> eth0: Device is fully-supported using driver 'sky2'. NetworkManager: <info> (eth0): exporting device as /org/freedesktop/NetworkManager/Device/2 NetworkManager: <info> Now managing wired Ethernet (802.3) device 'eth0'. NetworkManager: <info> Bringing up device eth0 NetworkManager: <info> Deactivating device eth0. NetworkManager: <info> eth1: Device is fully-supported using driver 'bcm43xx'. NetworkManager: <info> (eth1): exporting device as /org/freedesktop/NetworkManager/Device/3 NetworkManager: <info> Now managing wireless (802.11) device 'eth1'. NetworkManager: <info> Bringing up device eth1 NetworkManager: <info> Deactivating device eth1. NetworkManager: <info> (eth0) supplicant interface is now in state 2 (from 1). NetworkManager: <info> (eth1) supplicant interface is now in state 2 (from 1). NetworkManager: <info> SWITCH: no current connection, found better connection 'Auto Ethernet (eth0)'. NetworkManager: <info> Activating device eth0 NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) scheduled... NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) started... NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) scheduled... NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device Prepare) complete. NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) starting... NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) successful. NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) scheduled. NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device Configure) complete. NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) started... NetworkManager: <info> Activation (eth0) Beginning DHCP transaction. Internet Systems Consortium DHCP Client V3.0.5 Copyright 2004-2006 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ NetworkManager: <info> dhclient started with pid 17573 NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure Start) complete. Error: Could not acquire the NM DHCP client service. Message: (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.41" is not allowed to own the service "org.freedesktop.nm_dhcp_client" due to security policies in the configuration file Listening on LPF/eth0/00:16:d3:5b:d2:ae Sending on LPF/eth0/00:16:d3:5b:d2:ae Sending on Socket/fallback DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 DHCPOFFER from 10.36.251.1 DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 10.36.251.1 Error: Could not acquire the NM DHCP client service. Message: (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.42" is not allowed to own the service "org.freedesktop.nm_dhcp_client" due to security policies in the configuration file bound to 10.36.253.137 -- renewal in 128334 seconds. how should I fix the nm_dhcp_client dbus problem? What should I do? Thank you for helping me. Sincerely, Richard Chang 2007/11/19, Yung-Ting Chang <[EMAIL PROTECTED]>: > Sorry for bothering all guys. > I tried to svn check out Networkmanager-0.7 and nm-applet from SVN > (revision 3095) > i followed some information from mail-list and following is what's i did > > > and following is the wpa_supplicant message: > > #wpa_supplicant -u -dd > Providing DBus service 'fi.epitest.hostap.WPASupplicant'. > Initializing interface 'eth0' conf 'N/A' driver 'wired' ctrl_interface > 'N/A' bridge 'N/A' > Initializing interface (2) 'eth0' > EAPOL: SUPP_PAE entering state DISCONNECTED > EAPOL: KEY_RX entering state NO_KEY_RECEIVE > EAPOL: SUPP_BE entering state INITIALIZE > EAP: EAP entering state DISABLED > EAPOL: External notification - portEnabled=0 > EAPOL: External notification - portValid=0 > wpa_driver_wired_init: Added multicast membership with packet socket > Own MAC address: 00:16:d3:5b:d2:ae > Setting scan request: 0 sec 100000 usec > Added interface eth0 > Using wired driver - overriding ap_scan configuration > Initializing interface 'eth1' conf 'N/A' driver 'wext' ctrl_interface > 'N/A' bridge 'N/A' > Initializing interface (2) 'eth1' > EAPOL: SUPP_PAE entering state DISCONNECTED > EAPOL: KEY_RX entering state NO_KEY_RECEIVE > EAPOL: SUPP_BE entering state INITIALIZE > EAP: EAP entering state DISABLED > EAPOL: External notification - portEnabled=0 > EAPOL: External notification - portValid=0 > SIOCSIFFLAGS: No such device > Could not set interface 'eth1' UP > SIOCGIWRANGE: WE(compiled)=22 WE(source)=18 enc_capa=0xf > capabilities: key_mgmt 0xf enc 0xf > WEXT: Operstate: linkmode=1, operstate=5 > Own MAC address: 00:19:7e:8c:05:b0 > wpa_driver_wext_set_wpa > wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0 > wpa_driver_wext_set_countermeasures > wpa_driver_wext_set_drop_unencrypted > Setting scan request: 1 sec 100000 usec > Added interface eth1 > RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > Wireless event: cmd=0x8b06 len=8 > RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > Wireless event: cmd=0x8b1a len=8 > RTM_NEWLINK: operstate=0 ifi_flags=0x1002 () > Wireless event: cmd=0x8b2a len=8 > l2_packet_receive - recvfrom: Network is down > Setting scan request: 0 sec 0 usec > State: DISCONNECTED -> SCANNING > Starting AP scan (broadcast SSID) > Trying to get current scan results first without requesting a new scan > to speed up initial association > Received 0 bytes of scan results (0 BSSes) > Scan results: 0 > No suitable AP found. > Setting scan request: 0 sec 0 usec > No enabled networks - do not scan > State: SCANNING -> INACTIVE > Received 0 bytes of scan results (0 BSSes) > Scan results: 0 > Ignore event for foreign ifindex 2 > ---------------- > > #NetworkManager --no-daemon > > NetworkManager: <info> starting... > NetworkManager: <info> eth0: Device is fully-supported using driver 'sky2'. > NetworkManager: <info> (eth0): exporting device as > /org/freedesktop/NetworkManager/Device/2 > NetworkManager: <info> Now managing wired Ethernet (802.3) device 'eth0'. > NetworkManager: <info> Bringing down device eth0 > NetworkManager: <info> Bringing up device eth0 > NetworkManager: <info> Deactivating device eth0. > NetworkManager: <info> eth1: Device is fully-supported using driver > 'bcm43xx'. > NetworkManager: <info> (eth1): exporting device as > /org/freedesktop/NetworkManager/Device/3 > NetworkManager: <info> Now managing wireless (802.11) device 'eth1'. > NetworkManager: <info> Bringing down device eth1 > NetworkManager: <info> Bringing up device eth1 > NetworkManager: <info> Deactivating device eth1. > NetworkManager: <info> (eth0) supplicant interface is now in state 2 (from > 1). > NetworkManager: <info> (eth1) supplicant interface is now in state 2 (from > 1). > ----------------- > > > Then the NetworkManager hang on here. > Is there any advise for me to solve this? thank you a lot! > should I run nm-applet by myself? > i ever tried to run nm-applet by myself but still doesn't work and > shown the following message: > > NetworkManager: <info> starting... > NetworkManager: <info> eth0: Device is fully-supported using driver 'sky2'. > NetworkManager: <info> (eth0): exporting device as > /org/freedesktop/NetworkManager/Device/2 > NetworkManager: <info> Now managing wired Ethernet (802.3) device 'eth0'. > NetworkManager: <info> Bringing up device eth0 > NetworkManager: <info> Deactivating device eth0. > NetworkManager: <info> eth1: Device is fully-supported using driver > 'bcm43xx'. > NetworkManager: <info> (eth1): exporting device as > /org/freedesktop/NetworkManager/Device/3 > NetworkManager: <info> Now managing wireless (802.11) device 'eth1'. > NetworkManager: <info> Bringing up device eth1 > NetworkManager: <info> Deactivating device eth1. > NetworkManager: <info> (eth0) supplicant interface is now in state 2 (from > 1). > NetworkManager: <info> (eth1) supplicant interface is now in state 2 (from > 1). > NetworkManager: <info> SWITCH: no current connection, found better > connection 'Auto Ethernet (eth0)'. > NetworkManager: <info> Activating device eth0 > NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device > Prepare) scheduled... > NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device > Prepare) started... > NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device > Configure) scheduled... > NetworkManager: <info> Activation (eth0) Stage 1 of 5 (Device > Prepare) complete. > NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device > Configure) starting... > NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device > Configure) successful. > NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure > Start) scheduled. > NetworkManager: <info> Activation (eth0) Stage 2 of 5 (Device > Configure) complete. > NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure > Start) started... > NetworkManager: <info> Activation (eth0) Beginning DHCP transaction. > Internet Systems Consortium DHCP Client V3.0.5 > Copyright 2004-2006 Internet Systems Consortium. > All rights reserved. > For info, please visit http://www.isc.org/sw/dhcp/ > > NetworkManager: <info> dhclient started with pid 17573 > NetworkManager: <info> Activation (eth0) Stage 3 of 5 (IP Configure > Start) complete. > Error: Could not acquire the NM DHCP client service. Message: > (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.41" is not > allowed to own the service "org.freedesktop.nm_dhcp_client" due to > security policies in the configuration file > Listening on LPF/eth0/00:16:d3:5b:d2:ae > Sending on LPF/eth0/00:16:d3:5b:d2:ae > Sending on Socket/fallback > DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 > DHCPOFFER from 10.36.251.1 > DHCPREQUEST on eth0 to 255.255.255.255 port 67 > DHCPACK from 10.36.251.1 > Error: Could not acquire the NM DHCP client service. Message: > (org.freedesktop.DBus.Error.AccessDenied) Connection ":1.42" is not > allowed to own the service "org.freedesktop.nm_dhcp_client" due to > security policies in the configuration file > bound to 10.36.253.137 -- renewal in 128334 seconds. > ----------- > > here is my device info: > wpa_supplicant v0.5.8 > > NetworkManager Tool > > State: disconnected > > - Device: eth0 > ---------------------------------------------------------------- > Type: Wired > Driver: sky2 > Active: no > HW Address: XX:XX:XX:XX:XX:XX > > Capabilities: > Supported: yes > Carrier Detect: yes > Speed: 100 Mb/s > > Wired Settings > > > - Device: eth1 > ---------------------------------------------------------------- > Type: 802.11 Wireless > Driver: bcm43xx > Active: no > HW Address: XX:XX:XX:XX:XX:XX > > Capabilities: > Supported: yes > > Wireless Settings > WEP Encryption: yes > WPA Encryption: yes > WPA2 Encryption: yes > > thank you for your help > > Richard Chang. > _______________________________________________ NetworkManager-list mailing list [email protected] http://mail.gnome.org/mailman/listinfo/networkmanager-list
