Hi all, I'd really like to keep base64 to a bare minimum in my mail-store, but then along comes monstrosities like the attached. Trying to run mhfixmsg on it just removes the entire body of the mail.
I just tried running the nmh-1.7-RC2 version, but result is same. I'm not holding my breath, but maybe the attachment could provide a test-case ... --- Regards, Håkon
--- Begin Message ---Hi All, I’m happily running mythbuntu 16.04.2 and have had lircd working with devinput to receive my MCE IR remote control input quite happily. lsusb shows the device as: Bus 002 Device 002: ID 0471:060c Philips (or NXP) Consumer Infrared Transceiver (HP) For ages I’ve been wanting to play with the transmit side of the mceusb device but all my attempts to use irsend(1) fail with: root@spug:~# irsend -d /dev/lircd SET_TRANSMITTERS 0 irsend: command failed: SET_TRANSMITTERS 0 irsend: hardware does not support sending root@spug:~# irsend -d /dev/lircd SET_TRANSMITTERS 1 irsend: command failed: SET_TRANSMITTERS 1 irsend: hardware does not support sending root@spug:~# irsend -d /dev/lircd SET_TRANSMITTERS 2 irsend: command failed: SET_TRANSMITTERS 2 irsend: hardware does not support sending root@spug:~# irsend SEND_ONCE "devinput" "MENU" irsend: command failed: SEND_ONCE devinput MENU irsend: hardware does not support sending I can see that various lircd and mceusb kernel modules are loaded but I’m at a bit of a loss as to how to get IR transmission working: root@spug:~# lsmod|egrep '(lirc|mce)' ir_lirc_codec 16384 0 lirc_dev 20480 1 ir_lirc_codec ir_mce_kbd_decoder 16384 0 rc_rc6_mce 16384 0 mceusb 28672 0 rc_core 28672 14 ir_sharp_decoder,ir_xmp_decoder,lirc_dev,ir_lirc_codec,ir_rc5_decoder,ir_nec_decoder,ir_sony_decoder,mceusb,ir_mce_kbd_decoder,ir_jvc_decoder,ir_rc6_decoder,ir_sanyo_decoder,rc_rc6_mce The kernel does recognise the device and notices when the IR transmitter is plugged in: root@spug:~# dmesg|grep mce [ 0.016824] mce: CPU supports 6 MCE banks [ 13.332036] Registered IR keymap rc-rc6-mce [ 13.338220] input: MCE IR Keyboard/Mouse (mceusb) as /devices/virtual/input/input11 [ 13.343049] rc rc0: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0 [ 13.548043] mceusb 2-2:1.0: Registered BB+ Dongle(e.d) with mce emulator interface version 1 [ 13.548047] mceusb 2-2:1.0: 2 tx ports (0x1 cabled) and 2 rx sensors (0x1 active) [ 13.548084] usbcore: registered new interface driver mceusb I have read that the devinput lircd driver doesn’t support transmission but I can’t seem to find the appropriate one to use for the mceusb device: root@spug:~# lircd --driver=help Driver `help' not supported. Supported drivers: accent alsa_usb asusdh atilibusb atwf83 audio audio_alsa awlibusb bte bw6130 commandir creative creative_infracd default devinput dfclibusb dsp dvico ea65 ftdi i2cuser irlink irman livedrive_midi livedrive_seq logitech macmini mp3anywhere mplay mplay2 mouseremote mouseremote_ps2 null pcmak pinsys pixelview samsung sb0540 silitek srm7500libusb tira tira_raw udp uirt2 uirt2_raw usb_uirt_raw usbx Ideally, I’d like to learn how to manually run the appropriate lircd command from the command-line, specify all the needed options and get it working with irsend independent of the mythbuntu startup scripts. Any help or advice hugely appreciated! Cheers, Doug_______________________________________________ mythtv-users mailing list [email protected] http://lists.mythtv.org/mailman/listinfo/mythtv-users http://wiki.mythtv.org/Mailing_List_etiquette MythTV Forums: https://forum.mythtv.org
--- End Message ---
_______________________________________________ Nmh-workers mailing list [email protected] https://lists.nongnu.org/mailman/listinfo/nmh-workers
