Matt: The NPDE and NPD systems in NONMEM are described in the nm744.pdf manual ( https://nonmem.iconplc.com/nonmem744 ), pages 70-75, and follow along the work of Comet, Brendel, Ngyuen, Mentre, etc. The NPDE R package is not used within NONMEM.
Robert J. Bauer, Ph.D. Senior Director Pharmacometrics R&D ICON Early Phase 820 W. Diamond Avenue Suite 100 Gaithersburg, MD 20878 Office: (215) 616-6428 Mobile: (925) 286-0769 [email protected]<mailto:[email protected]> www.iconplc.com<http://www.iconplc.com> From: [email protected] <[email protected]> On Behalf Of Matthew Fidler Sent: Thursday, September 3, 2020 6:08 AM To: Jeroen Elassaiss-Schaap (PD-value B.V.) <[email protected]> Cc: Bill Denney <[email protected]>; Mu'taz Jaber <[email protected]>; [email protected] Subject: Re: [NMusers] M3 method - WRES, and CWRES Hi everyone, As an aside, nlmixr's upcoming release (that supports censoring) simulates a value using a truncated normal based on the ipred, variance at that point and the censoring column to produce an observation. This observation is used to calculate RES, WRES, CWRES. It is flagged so you can see which values use this approach. In theory, since this is simulated from the IPRED/truncated the CWRES would be likely follow the distribution closer. I'm unsure if the new NONMEM uses this approach. Another question from my end is the NPDE: There are many methods to handle BLQ values with NPDE R package, does anyone know which NONMEM uses? Or do you need to use the NPDE package to get these values from NONMEM? Matt. On Wed, Sep 2, 2020 at 2:09 AM Jeroen Elassaiss-Schaap (PD-value B.V.) <[email protected]<mailto:[email protected]>> wrote: Hi Mutaz, Bill, It might be useful to use NPDEs, as discussed in https://www.cognigen.com/nmusers/2019-February/7376.html<https://www.cognigen.com/nmusers/2019-February/7376.html>; the whole thread is worthwhile reading. NPDEs can be calculated also for BQL values. Bill -thanks for pointing to excellent post of Matt! I would take as most important point that CWRES for non-BQL values, calculated with a model with influential BQL, are biased because the influence of the BQL values is not accounted for. (if a certain prediction for a measurable concentration is changed by 10% because of the M3 method, that will turn up as a similar bias in CWRES). The NPDEs as referenced to in the above discussion (Nguyen2012 JPKPD 0.1007/s10928-012-9264-2) do not suffer from that drawback as one can see the complete profile (cf Fig 8 of Nguyen2012). Hope this helps, Jeroen http://pd-value.com<http://pd-value.com> [email protected]<mailto:[email protected]> @PD_value +31 6 23118438 -- More value out of your data! On 2/9/20 2:32 am, Bill Denney wrote: Hi Mutaz, Matt Hutmacher described it well here: https://www.cognigen.com/nmusers/2010-April/2448.html<https://www.cognigen.com/nmusers/2010-April/2448.html> A very brief summary of his excellent post is that subjects with a combination of censored (BLQ) an uncensored (above the LLOQ and below the ULOQ) will be biased in their reporting of CWRES because you cannot calculate CWRES for BLQ values. (I say this before looking up what MDVRES does.) My guess that Bob or someone else can confirm is that the bias is anticipated to be relatively small compared to the value of being able to compare CWRES values the other observations for a subject. It does not definitively mean that the results are unbiased (see Matt’s Tmax example), but generally, the CWRES values previously omitted are more useful than excluding them from calculation. Thanks, Bill From: [email protected]<mailto:[email protected]> <[email protected]<mailto:[email protected]>> On Behalf Of Mu'taz Jaber Sent: Tuesday, September 1, 2020 7:25 PM To: [email protected]<mailto:[email protected]> Subject: [NMusers] M3 method - WRES, and CWRES All, Back in April 2010, Sebastian Bihorel and Martin Bergstrand initiated a discussion regarding using the M3 and M4 methods for handling BQL data and how it seemed to be a bug that NONMEM wouldn't compute WRES for the entire set of subject data records whenever a BQL was included (https://www.cognigen.com/nmusers/2010-April/2445.html<https://www.cognigen.com/nmusers/2010-April/2445.html>). Tom Ludden responded with the following post (https://www.cognigen.com/nmusers/2010-April/2447.html<https://www.cognigen.com/nmusers/2010-April/2447.html>): This issue was discussed with Stuart Beal. He believed that weighted residuals would be incorrect for an individual that had both continuous dependent variables and a likelihood in the calculation of their contribution to the objective function value, as is the case with his M3 or M4 BQL methods The code for both RES and WRES are intentionally bypassed in these cases. Since then, we now have easy functionality with the F_FLAG=1 condition of the M3/M4 code in $ERROR to tack on MDVRES=1 that allows the calculation of WRES and CWRES to be available in output tables. My questions are: Is Stuart Beal's original concern still valid? Do these NONMEM updates give us appropriate WRES and CWRES for plotting purposes for individuals whose records contain BQL data? Thank you, Mutaz Jaber PhD student University of Minnesota ------------------------------------------------------- Mutaz M. Jaber, PharmD. PhD student, Pharmacometrics Experimental and Clinical Pharmacology University of Minnesota 717 Delaware St SE; Room 468 Minneapolis, MN 55414 Email: [email protected]<mailto:[email protected]> Phone: +1 651-706-5202 ~ Stay curious <br /><br /> ICON plc made the following annotations. ------------------------------------------------------------------------------ This e-mail transmission may contain confidential or legally privileged information that is intended only for the individual or entity named in the e-mail address. If you are not the intended recipient, you are hereby notified that any disclosure, copying, distribution, or reliance upon the contents of this e-mail is strictly prohibited. If you have received this e-mail transmission in error, please reply to the sender, so that ICON plc can arrange for proper delivery, and then please delete the message. Thank You, ICON plc South County Business Park Leopardstown Dublin 18 Ireland Registered number: 145835
