Dear Sir,
I am writing to thank you for your letter and say,
On Thu, Dec 16, 2004 at 10:24:19PM -0600, Burton Strauss wrote:
> S:
.. snip
> Try this --
>
> After ./configure, edit config.h and look for #define INET6 1. Change that
> to #undef INET6.
>
I have already run configure so I didn't do say again (thinking that
configure will recreate config.h from config.h.in).
> Do the usual gmake and gmake install.
>
> When you start ntop, be sure and give a full -w specification, i.e. -w
> 192.168.x.x:3000
Ok. Unfortunately, I failed to understand Mr Buff's request to do that
formerly.
Result with -w a.b.c.d:3000 and #undef INET6 in config.h
Dec 17 15:51:47 pc09011 ntop[52172]: SSL is present but https is
disabled: use -W <https port> for enabling it
Dec 17 15:51:47 pc09011 ntop[52172]: INITWEB: Initializing web server
Dec 17 15:51:47 pc09011 ntop[52172]: INITWEB: Initializing tcp/ip
socket connections for web server
Dec 17 15:51:47 pc09011 ntop[52172]: INITWEB: Converted address
'a.b.c.d' - binding to the specific interface
Dec 17 15:51:47 pc09011 ntop[52172]: **FATAL_ERROR** INITWEB: Unable
to create a new socket - returned 0, error is 'Unknown error: 0'(0)
The result is the same when only the port is specified with -w.
Have I cocked it up ?
*** config.h.orig Fri Dec 17 15:38:12 2004
--- config.h Fri Dec 17 15:48:01 2004
***************
*** 641,647 ****
#define HAVE_ZLIB_H 1
/* Enable/disable ipv6 support */
! #define INET6 1
/* Define to 1 if `lstat' dereferences a symlink specified with a
trailing
slash. */
--- 641,651 ----
#define HAVE_ZLIB_H 1
/* Enable/disable ipv6 support */
! #undef INET6
!
! /* #define INET6 1
! Mr Strauss's suggestion to deal with web server hang
! */
/* Define to 1 if `lstat' dereferences a symlink specified with a
trailing
slash. */
The single homed host (fxp0) has INET6 support available but not built
in the kernel.
pc09011> ifconfig fxp0
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet a.b.c.d netmask 0xffffff00 broadcast a.b.c.255
ether 00:d0:b7:85:28:40
media: Ethernet autoselect (10baseT/UTP)
status: active
pc09011>
>
> It takes a LONG time for the 1st page to come up, but it seems ok after
> that.
>
> -----Burton
>
>
> -----Original Message-----
> On Thu, Dec 16, 2004 at 05:29:59PM -0800, Kurt Buff wrote:
>
> > What happens if you specify the ports with ip.add.re.ss:port pair?
> >
>
Yours sincerely.
--
Stanley Hopcroft
IP Australia
Ph: (02) 6283 3189 Fax: (02) 6281 1353
PO Box 200 Woden ACT 2606
http://www.ipaustralia.gov.au
--
This message contains privileged and confidential information only
for use by the intended recipient. If you are not the intended
recipient of this message, you must not disseminate, copy or use
it in any manner. If you have received this message in error,
please advise the sender by reply e-mail. Please ensure all
e-mail attachments are scanned for viruses prior to opening or
using.
_______________________________________________
Ntop mailing list
[EMAIL PROTECTED]
http://listgateway.unipi.it/mailman/listinfo/ntop
