On Sun, 2010-01-31 at 16:09 -0500, Charles Lepple wrote: > On Jan 31, 2010, at 3:56 PM, chance fulton wrote: > > > On Sun, 2010-01-31 at 14:38 -0500, Charles Lepple wrote: > >> On Jan 31, 2010, at 1:44 PM, chance fulton wrote: > >> > >>> Original Message > >>>> I have 2 SmartUOS1050SLT's that apparently protocol 3004, has there > >>>> been > >>>> any progress on getting these units supported under nut? I am > >>>> running > >>>> version 2.4.1, and get the following output when starting the > >>>> driver. > >>> > >>>> #lsusb > >>>> Bus 005 Device 002: ID 09ae:0001 Tripp Lite > >>> > >>>> # upsdrvctl -DDDD start > >>>> Network UPS Tools - UPS driver controller 2.4.1 > >>>> Starting UPS: tripplite > >>>> exec: /lib/nut/tripplite_usb -a tripplite > >>>> Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 > >>>> (2.4.1) > >>>> Warning: This is an experimental driver. > >>>> Some features may not function correctly. > >>> > >>>> Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT > >>>> Unknown input voltage range: 0x02 > >>>> Unknown number of switchable load banks: 0x00 > >>>> Unit ID: 0 > >>>> Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT > >>>> Unknown value for s[1]: 0x01 > >> > [...] > > >> Please post a few details about your OS distribution and version. > >> > > I have Ubuntu server 9.10 Kernel 2.6.31-17-generic-pae > > I have just installed Network UPS Tools - UPS driver controller > > 2.4.1-r2286 > > > > And still have the same issue. > > I just committed a few changes to SVN. In a few minutes, it should > build another tarball for r2294: > > http://buildbot.ghz.cc/public/nut/waterfall?branch=trunk&builder=Debian-etch-x86 > > A couple of questions: > > - When you were testing, how did you run the driver? > - Is the Ubuntu package for NUT still installed? > - Are you using SVN, or the tarballs? > > thanks, > > - Charles OK will do, as for the questions.
I run the driver from this command: sudo /usr/local/ups/bin/upsdrvctl start I uninstalled the Ubuntu package, and purged the configs. then I copied in my settings from the old installation to the new config files. I am using the tarballs as I an new with the whole autoconf thing, and could not get it going. I have just removed the previous version, and installed from the svn trunk version 2297. I now get this. Network UPS Tools - UPS driver controller 2.4.1-2297 Network UPS Tools - Tripp Lite OMNIVS / SMARTPRO driver 0.20 (2.4.1-2297) Warning: This is an experimental driver. Some features may not function correctly. Detected a UPS: TRIPP LITE/TRIPP LITE SMART1050SLT libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' libusb_get_interrupt() returned 0 instead of 8 while sending 3a 00 ff 0d 00 00 00 00 '........' Unknown input voltage range: 0x02 Unknown number of switchable load banks: 0x00 Unit ID: 0 Unknown protocol (3004)Attached to Tripp Lite SMART1050SLT Unknown value for s[1]: 0x01 Pretty much the same, just more debug info. _______________________________________________ Nut-upsdev mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsdev
