Hello, I had running OpenMediaVault server with NUT 2.4.3 megatec_usb driver. After the OMV upgrade, NUT also upgraded to 2.6.4. I realised that megatec_usb removed in this version. So I have configured to use blazer_usb driver. However NUT behaves incorrectly after switching blazer_usb. System is being halted upon booted up. Is it possible to use megatec_usb driver in the new version?
# NUT 2.4.3 with megatec_usb driver battery.charge: 98.3 battery.voltage: 27.00 battery.voltage.nominal: 23.5 device.mfr: TUNCMATIK device.model: DG1200VA VER1.01C device.serial: unknown device.type: ups driver.name: megatec_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 1.6 input.frequency: 50.0 input.frequency.nominal: 50.0 input.voltage: 220.0 input.voltage.fault: 165.0 input.voltage.maximum: 226.0 input.voltage.minimum: 217.0 input.voltage.nominal: 220.0 output.voltage: 220.0 ups.beeper.status: disabled ups.delay.shutdown: 0 ups.delay.start: 2 ups.load: 0.0 ups.mfr: TUNCMATIK ups.model: DG1200VA VER1.01C ups.serial: unknown ups.status: OL OFF ups.type: standby # NUT 2.6.4 with blazer_usb driver battery.charge: 100 battery.voltage: 27.00 battery.voltage.high: 25.46 battery.voltage.low: 20.37 battery.voltage.nominal: 23.5 device.mfr: TUNCMATIK device.model: DG1200VA device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.6.4 driver.version.internal: 0.08 input.current.nominal: 8.0 input.frequency: 50.0 input.frequency.nominal: 50 input.voltage: 212.0 input.voltage.fault: 165.0 input.voltage.nominal: 220 output.voltage: 212.0 ups.alarm: Shutdown imminent! ups.beeper.status: disabled ups.delay.shutdown: 30 ups.delay.start: 180 ups.firmware: VER1.01C ups.load: 0 ups.mfr: TUNCMATIK ups.model: DG1200VA ups.productid: 0000 ups.status: ALARM OL FSD ups.temperature: 0.0 ups.type: offline / line interactive ups.vendorid: 0001 #NUT logs 1. Feb 22 19:48:43 microserver upsd[2586]: listening on 127.0.0.1 port 3493 2. Feb 22 19:48:43 microserver upsd[2586]: Connected to UPS [ups]: blazer_usb-ups 3. Feb 22 19:48:43 microserver upsd[2596]: Startup successful 4. Feb 22 19:48:43 microserver upsd[2596]: User [email protected] logged into UPS [ups] 5. Feb 22 19:48:43 microserver upsmon[2608]: Startup successful 6. Feb 22 19:48:48 microserver upsmon[2610]: UPS ups@localhost: forced shutdown in progress 7. Feb 22 19:48:48 microserver upsd[2596]: Client [email protected] set FSD on UPS [ups] 8. Feb 22 19:48:48 microserver upsmon[2610]: Executing automatic power-fail shutdown 9. Feb 22 19:48:48 microserver upsmon[2610]: Auto logout and shutdown proceeding 10. Feb 22 19:48:48 microserver upssched[2760]: Executing command: notify 11. Feb 22 19:48:48 microserver upssched[2758]: Executing command: forced-shutdown 12. Feb 22 19:48:48 microserver upsmon[2610]: Signal 10: User requested FSD 13. Feb 22 19:48:49 microserver upssched-cmd: UPS ups@localhost: - Forced shutdown in progress 14. Feb 22 19:48:49 microserver upssched-cmd: Automatic logout and shutdown proceeding # dmesg usbfs: USBDEVFS_CONTROL failed cmd blazer_usb rqt 128 rq 6 len 255 ret -110 Regards. Mustafa T.
_______________________________________________ Nut-upsdev mailing list [email protected] http://lists.alioth.debian.org/cgi-bin/mailman/listinfo/nut-upsdev
