On Thu, Jun 26, 2008 at 11:07 AM, Arjen de Korte <[EMAIL PROTECTED]> wrote: >> Well.. lets try. I believe there must the way through. As a last resort >> it should be possible to allow user select concrete model or parameter >> set by hands.. > > Not with the existing HAL interface, or we should somehow hardcode a path > to a configuration file.
Well, what's wrong with hardcoded path to configuration file? Just make this ./configure parameter with something meaningful (e.g. /etc/nut/) by default and that's it. :) >> I haven't dealt with hal drivers before, so I would appreciate if you >> describe more precisely how to run it in debug mode :) > > This isn't possible. You need to run the (not HAL) 'megatec_usb' driver in > debug mode (see my previous reply). Ok, I've removed nut-hal-drivers and installed plain nut, but megatec_usb doesn't want to connect to my UPS. Seems like it can't get rid of usbhid driver, attached to it by kernel: # /lib/nut/megatec_usb -a ippon -DDD [... a lot of other unrelevant stuff...] Checking device (06DA/0003) (002/003) - VendorID: 06da - ProductID: 0003 - Manufacturer: unknown - Product: unknown - Serial Number: unknown - Bus: 002 Trying to match device Device matches failed to claim USB device, trying 2 more time(s)... detaching kernel driver from USB device... failed to detach kernel driver from USB device... trying again to claim USB device... failed to claim USB device, trying 1 more time(s)... detaching kernel driver from USB device... failed to detach kernel driver from USB device... trying again to claim USB device... failed to claim USB device, trying 0 more time(s)... detaching kernel driver from USB device... failed to detach kernel driver from USB device... trying again to claim USB device... Successfully reconnected Q1 => FAILED [short read] Q1 detail: (0 bytes) => 5 out of 5 detection attempts failed (minimum failures: 2). Megatec protocol UPS not detected. Here is excerpt from /proc/bus/usb/devices: T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=06da ProdID=0003 Rev= 4.00 S: Manufacturer=OMRON S: Product=USB UPS C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=20ms >> Output of 'lsusb -vvv' is following. For me it seems we have nothing like >> ID, which could be used... >> >> Bus 002 Device 002: ID 06da:0003 Phoenixtec Power Co., Ltd > > This sadly looks familiar... :-( > Yup, this the ubiquitous USB-to-serial converter from Phoenixtec. By the way, in nut configs this VID/PID is mentioned as Mustek Powermust 600USB (OMRON/87XXUPS) And in other place we could find #define LIEBERT_VENDORID 0x06da which I think is either totally wrong or needs clarification, because other UPS use this VID too. -- Regards, Alexander Chemeris. SIPez LLC. SIP VoIP, IM and Presence Consulting http://www.SIPez.com tel: +1 (617) 273-4000 _______________________________________________ Nut-upsuser mailing list [email protected] http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser
