One quick test. Can ping the group ip with eth2. Recent versions of debian/ubuntu fail that test. So I could nvr get that path 2 work. If u down eth1 eth2 usually starts 2 work. So it's likely something with standard routing.
Also Equallogic has a white paper on setting up OIS with debian. Might want to use current tar ball vs dkpg version. Might b a little stale. -don Sent from my iPhone On Jul 8, 2010, at 6:56 PM, Laurent <[email protected]> wrote: > Hello, > Thank you for the work. This is my 1st post here. > > Under a Debian OS, i try to acces by two different paths an Equallogic > PS 6000. > > On the server i configured two NICs > > eth1 Link encap:Ethernet HWaddr b8:ac:6f:12:38:c9 > inet adr:192.168.15.11 Bcast:192.168.15.255 Masque: > 255.255.255.0 > > eth2 Link encap:Ethernet HWaddr b8:ac:6f:12:38:cb > inet adr:192.168.15.12 Bcast:192.168.15.255 Masque: > 255.255.255.0 > On the same vlan than the SAN > > First, the discovery works fine: > > iscsiadm -m discovery -t st -I eth1 -I eth2 -p 192.168.15.1 -P 1 -o > delete -o new > Target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb > Portal: 192.168.15.1:3260,1 > Iface Name: eth2 > Iface Name: eth1 > > With EQL, there is only one IP address for the portal, regardless of > how many times i have to access it. > > I try to connect via the two nics: > > First one: > #iscsiadm -m node --targetname iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb -I eth1 --portal > 192.168.15.1:3260,13 --login > Logging in to [iface: eth1, target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb, portal: > 192.168.15.1,3260] > Logging in to [iface: eth1, target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb, portal: > 192.168.15.1,3260] > Login to [iface: eth1, target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb, portal: > 192.168.15.1,3260]: successful > # > > All is fine with the first one. > ls /dev/sdb > /dev/sdb > mount /dev/sdb /media/testDB/ > > Jul 9 00:42:10 sx1 kernel: [ 3318.053517] scsi 9:0:0:0: Direct- > Access EQLOGIC 100E-00 4.3 PQ: 0 ANSI: 5 > Jul 9 00:42:10 sx1 kernel: [ 3318.057042] sd 9:0:0:0: [sdb] 209725440 > 512-byte hardware sectors (107379 MB) > Jul 9 00:42:10 sx1 kernel: [ 3318.057042] sd 9:0:0:0: [sdb] Write > Protect is off > Jul 9 00:42:10 sx1 kernel: [ 3318.057379] sd 9:0:0:0: [sdb] Write > cache: disabled, read cache: enabled, doesn't support DPO or FUA > Jul 9 00:42:10 sx1 kernel: [ 3318.057734] sd 9:0:0:0: [sdb] 209725440 > 512-byte hardware sectors (107379 MB) > Jul 9 00:42:10 sx1 kernel: [ 3318.058035] sd 9:0:0:0: [sdb] Write > Protect is off > Jul 9 00:42:10 sx1 kernel: [ 3318.059480] sd 9:0:0:0: [sdb] Write > cache: disabled, read cache: enabled, doesn't support DPO or FUA > Jul 9 00:42:10 sx1 kernel: [ 3318.059527] sdb: unknown partition > table > Jul 9 00:42:10 sx1 kernel: [ 3318.060635] sd 9:0:0:0: [sdb] Attached > SCSI disk > Jul 9 00:42:10 sx1 kernel: [ 3318.060686] sd 9:0:0:0: Attached scsi > generic sg3 type 0 > Jul 9 00:43:51 sx1 kernel: [ 3419.896300] kjournald starting. Commit > interval 5 seconds > Jul 9 00:43:51 sx1 kernel: [ 3419.915116] EXT3 FS on sdb, internal > journal > Jul 9 00:43:51 sx1 kernel: [ 3419.915116] EXT3-fs: recovery complete. > Jul 9 00:43:51 sx1 kernel: [ 3419.915396] EXT3-fs: mounted filesystem > with ordered data mode. > > > > With eth2,, nothing happens. > iscsiadm -m node --targetname iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb -I eth2 --portal > 192.168.15.1:3260,13 --login > Logging in to [iface: eth2, target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb, portal: > 192.168.15.1,3260] > Logging in to [iface: eth2, target: iqn.2001-05.com.equallogic: > 0-8a0906-0dd652407-00e000e7b254c345-testdeb, portal: > 192.168.15.1,3260] > iscsiadm: Could not login to [iface: eth2, target: iqn. > 2001-05.com.equallogic:0-8a0906-0dd652407-00e000e7b254c345-testdeb, > portal: 192.168.15.1,3260]: > iscsiadm: initiator reported error (8 - connection timed out) > > I don't have any log line > > Is anyone an idea of what could happen ? > > Thank you very much, i am stuck > > > -- > You received this message because you are subscribed to the Google Groups > "open-iscsi" group. > To post to this group, send email to [email protected]. > To unsubscribe from this group, send email to > [email protected]. > For more options, visit this group at > http://groups.google.com/group/open-iscsi?hl=en. > -- You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/open-iscsi?hl=en.
