one more thing i have tested this in a centos IP6 disabled 5.2 server where am not getting
cnic: Unknown symbol __ipv6_addr_type cnic: Unknown symbol ip6_route_output but am geting "/dev/mysql/mysql: read failed after 0 of 4096 at 0: Input/output error" [r...@ussd1 /]# pvdisplay /dev/mysql/mysql: read failed after 0 of 4096 at 0: Input/output error --- Physical volume --- PV Name /dev/sdc1 VG Name mysql PV Size 300.03 GB / not usable 3.25 MB Allocatable yes PE Size (KByte) 4096 Total PE 76808 Free PE 51208 Allocated PE 25600 PV UUID JUPKC0-0p4S-odWF-kF2s-E1Kc-9D5x-KjTWZw On Nov 19, 1:03 pm, Bangalore <aneeshsu...@gmail.com> wrote: > Hi > > i have installed one HP blade server with "Linux version > 2.6.18-164.el5 (mockbu...@builder10.centos.org) (gcc version 4.1.2 > 20080704 (Red Hat 4.1.2-46)) 0000001 SMP Thu Sep 3 03:28:30 EDT 2009 " > CentOS release 5.4 (Final) .I have disabled the IP6 with these > commands by adding these in /etc/modeprob.conf > > alias net-pf-10 off > alias ipv6 off > options ipv6 disable=1 > > after that i installed iscsi and pointed towards one netapp .then i > created lvm in the system with netapp drive . > > when ever i restart a server or restart ISCSCI after that i am not not > able to access the LVM what i created . Please help me > > Additional Information dsmg log > > EXT3 FS on dm-2, internal journal > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > cxgb3i: tag itt 0x1fff, 13 bits, age 0xf, 4 bits. > iscsi: registered transport (cxgb3i) > cnic: Unknown symbol __ipv6_addr_type > cnic: Unknown symbol ip6_route_output > iscsi: registered transport (iser) > scsi1 : iSCSI Initiator over TCP/IP > Vendor: NETAPP Model: LUN Rev: 7310 > Type: Direct-Access ANSI SCSI revision: 04 > SCSI device sdb: 629225472 512-byte hdwr sectors (322163 MB) > sdb: Write Protect is off > sdb: Mode Sense: bd 00 00 08 > SCSI device sdb: drive cache: write through > SCSI device sdb: 629225472 512-byte hdwr sectors (322163 MB) > sdb: Write Protect is off > sdb: Mode Sense: bd 00 00 08 > SCSI device sdb: drive cache: write through > sdb: sdb1 > sd 1:0:0:0: Attached scsi disk sdb > sd 1:0:0:0: Attached scsi generic sg0 type 0 > > [r...@wapdb-node2 aneesh]# service iscsi restart > Logging out of session [sid: 2, target: iqn.1986-03.com.ibm:sn. > 135057127, portal: 10.0.104.202,3260] > Logout of [sid: 2, target: iqn.1986-03.com.ibm:sn.135057127, portal: > 10.0.104.202,3260]: successful > Stopping iSCSI daemon: > iscsid dead but pid file exists [ OK ] > Starting iSCSI daemon: WARNING: Error inserting libiscsi2 (/lib/ > modules/2.6.18-164.el5/kernel/drivers/scsi/libiscsi2.ko): Unknown > symbol in module, or unknown parameter (see dmesg) > FATAL: Error inserting bnx2i (/lib/modules/2.6.18-164.el5/kernel/ > drivers/scsi/bnx2i/bnx2i.ko): Unknown symbol in module, or unknown > parameter (see dmesg) > [ OK ] > [ OK ] > Setting up iSCSI targets: Logging in to [iface: default, target: iqn. > 1986-03.com.ibm:sn.135057127, portal: 10.0.104.202,3260] > Login to [iface: default, target: iqn.1986-03.com.ibm:sn.135057127, > portal: 10.0.104.202,3260]: successful > [ OK ] > [r...@wapdb-node2 aneesh]# > > [r...@wapdb-node2 /]# lvdisplay > /dev/MySql/MySql: read failed after 0 of 4096 at 0: Input/output > error > --- Logical volume --- > LV Name /dev/MySql/MySql > VG Name MySql > LV UUID dZ4DCD-qcxM-KnCt-xsrK-KyeM-pndo-0a5T9y > LV Write Access read/write > LV Status available > # open 1 > LV Size 300.00 GB > Current LE 76800 > Segments 1 > Allocation inherit > Read ahead sectors auto > - currently set to 256 > Block device 253:2 -- You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to open-is...@googlegroups.com. To unsubscribe from this group, send email to open-iscsi+unsubscr...@googlegroups.com. For more options, visit this group at http://groups.google.com/group/open-iscsi?hl=en.