On Wed, 2011-04-13 at 10:00 -0700, Mike Christie wrote:
> ccing Broadcom devs, Some questions for you guys below
>
>
> On 04/02/2011 01:34 PM, [email protected] wrote:
> > From: Vikas Chaudhary<[email protected]>
> >
> > To support multiple network addresses per adapter need to have a new way to
> > represent network interface (net iface) in sysfs.
> >
> > Currently only one ipaddress and hwaddress is displayed
> >
> > \# ls /sys/class/iscsi_host/host18
> > device hwaddress initiatorname ipaddress power subsystem uevent
> >
> > In this patch the net iface is presented as a separate class device.
> > The one that can be added/removed dynamically or statically, based on how
> > the user configures the multiple net iface on the adapter.
> >
> > The new sysfs directory would look like this
> > \# /sys/class/iscsi_iface/
> > |
> > |- ipv4-iface-<host_no>-<iface_no>/<-- for ipv4
> > |- ipaddress
> > |- subnet
> > |- gateway
> > |- bootproto
> > |- state
> > |- ipv6-iface-<host_no>-<iface_no>/<-- for ipv6
> > |- ipaddress
> > |- link_local_addr
> > |- router_addr
> > |- ipaddr_autocfg
> > |- linklocal_autocfg
> > |- state
> >
>
>
> With patch "[RFC-V2 PATCH 1/5] iscsi_transport: add support for
> set_net_config" userspace would send down the vlan info.
>
> If we add a vlan sysfs file to the iscsi_iface, to export the info was
> bnx2i going call iscsi_create_iface for each vlan? If so I am not sure
> what bnx2i will use for the iface_num. It is supposed to be persistent,
> right?
bnx2i doesn't need to know the IP addresses and VLANs for each HBA. It
is all handled in userspace by uIP. So if we add this sysfs,
iscsi_transport can handle sysfs creation for devices generically,
right?
>
> For bnx2i, when doing iscsi offload and vlans, do you have to have a
> netdev like ethX.Y setup for each vlan or can bnx2i operate without it
> (the call to cnic_get_vlan always throws me and I cannot remember if we
> were going to still do that or change something in the driver so you did
> not need it).
For now, cnic_get_vlan will try to get a matching VLAN from netdev with
a route to the target. But it is not required. Once we have VLAN
attribute in iface, uIP can override and use the VLAN specified in
iface.
>
> And just to confirm for vlans and bnx2i, when we make a ep and session,
> cnic_get_route/cnic_cm_select_dev will do the magic to figure out what
> vlan to use?
Yes for now. The plan is for uIP to override if a VLAN is specified in
iface.
This is the flow:
-> ep_connect
-> cnic_cm_connect
/* Try to get route/MTU/VLAN from netdev if available */
-> cnic_get_route
-> send nl message to uIP to get next hop
-> recv nl message from uIP
/* at this point we may get a new VLAN ID from uIP */
-> make connection to target
--
You received this message because you are subscribed to the Google Groups
"open-iscsi" group.
To post to this group, send email to [email protected].
To unsubscribe from this group, send email to
[email protected].
For more options, visit this group at
http://groups.google.com/group/open-iscsi?hl=en.
