2.0-871 is what I'm running Jeff
On Fri, Jan 4, 2013 at 4:17 PM, Jeff Bye <[email protected]> wrote: > I tried all of the commands and none of them worked for me: > > *deadlineserver@deadlineserver ~ $ iscsiadm -m discoverydb -t st -p > 10.10.0.1:3260 -o delete* > iscsiadm -m discovery [ -hV ] [ -d debug_level ] [-P printlevel] [ -t type > -p ip:port -I ifaceN ... [ -l ] ] | [ -p ip:port ] [ -o operation ] [ -n > name ] [ -v value ] > iscsiadm -m node [ -hV ] [ -d debug_level ] [ -P printlevel ] [ -L > all,manual,automatic ] [ -U all,manual,automatic ] [ -S ] [ [ -T targetname > -p ip:port -I ifaceN ] [ -l | -u | -R | -s] ] [ [ -o operation ] [ -n > name ] [ -v value ] ] > iscsiadm -m session [ -hV ] [ -d debug_level ] [ -P printlevel] [ -r > sessionid | sysfsdir [ -R | -u | -s ] [ -o operation ] [ -n name ] [ -v > value ] ] > iscsiadm -m iface [ -hV ] [ -d debug_level ] [ -P printlevel ] [ -I > ifacename ] [ [ -o operation ] [ -n name ] [ -v value ] ] > iscsiadm -m fw [ -l ] > iscsiadm -m host [ -P printlevel ] [ -H hostno ] > iscsiadm -k priority > > > *I checked man iscsiadm and found:* > -m, --mode op > specify the mode. op must be one of discovery, node, fw, > host iface or session. > > If no other options are specified: for discovery and > node, all of their respective records > are displayed; for session, all active sessions and > connections are displayed; for fw, all > boot firmware values are displayed; for host, all iSCSI > hosts are displayed; and for iface, > all ifaces setup in /etc/iscsi/ifaces are displayed. > > Am I running the wrong version perhaps? > > Jeff > > > > On Thu, Jan 3, 2013 at 7:05 PM, Mike Christie <[email protected]>wrote: > >> The iscsid.conf values are the defaults one used to setup the >> port/node/target db. If you clear the iscsid.conf values, you would >> still need to update the db ones for it to take effect on existing >> targets you have already setup. >> >> For the discovery values you can either delete the old discovery record: >> >> iscsiadm -m discoverydb -t st -p ip -o delete >> >> When you run the discovery command next, then it will use the >> iscsid.conf settings to create the discovery record. >> >> or if your tools does not support that command you can clear the chap >> settings >> >> iscsiadm -m discoverydb -t st -p ip -o update -n >> discovery.sendtargets.auth.username -v "" >> iscsiadm -m discoverydb -t st -p ip -o update -n >> discovery.sendtargets.auth.password -v "" >> iscsiadm -m discoverydb -t st -p ip -o update -n >> discovery.sendtargets.auth.authmethod -v none >> >> >> On 01/03/2013 01:46 PM, Jeff Bye wrote: >> > Hey! I've been out of town for a couple of weeks. Hope you had a >> > chance to take some time off as well :) >> > >> > It seems that the username and password I had initially set up is still >> > being used, however in iscsid.conf CHAP is set to "none" and any other >> > information has been commented. Does this only affect the target side? >> > >> > Jeff >> > >> > When I had it running on a windows machine (a temporary setup) we kept >> > it open and >> > On Fri, Dec 21, 2012 at 1:32 AM, Mike Christie <[email protected] >> > <mailto:[email protected]>> wrote: >> > >> > On 12/20/2012 06:54 PM, GGL wrote: >> > > deadlineserver@deadlineserver / $ sudo iscsiadm -m discovery -t >> > > sendtargets -p 10.10.0.1 >> > > iscsiadm: Login authentication failed with target >> > >> > Yeah, this is a CHAP failure. Is it turned off on the target too? >> > >> > Could you run >> > >> > sudo iscsiadm -m discovery -t sendtargets -p 10.10.0.1 -d 8 >> > >> > and send all the output? >> > >> > Also while running this command run: >> > >> > tcpdump -w iscsi.discovery.out -i your_eth_device >> > >> > and then send that iscsi.discovery.out file. It will show us what >> the >> > target is sending on the wire too. >> > >> > >> > Both of those files will have passwords in them if you have CHAP >> > settings still being used, so send me them in private or edit out >> the >> > values if you do not want them on the open. >> > >> > >> > >> > >> > -- >> > Jeff Bye >> > Graphics Coordinator >> > Liberty Post >> > 12910 Culver Blvd. Suite G >> > Los Angeles, CA 90066 >> > (310) 314-3900 x247 >> > >> > -- >> > You received this message because you are subscribed to the Google >> > Groups "open-iscsi" group. >> > To post to this group, send email to [email protected]. >> > To unsubscribe from this group, send email to >> > [email protected]. >> > For more options, visit this group at >> > http://groups.google.com/group/open-iscsi?hl=en. >> >> > > > -- > Jeff Bye > Graphics Coordinator > Liberty Post > 12910 Culver Blvd. Suite G > Los Angeles, CA 90066 > (310) 314-3900 x247 > -- Jeff Bye Graphics Coordinator Liberty Post 12910 Culver Blvd. Suite G Los Angeles, CA 90066 (310) 314-3900 x247 -- You received this message because you are subscribed to the Google Groups "open-iscsi" group. To post to this group, send email to [email protected]. To unsubscribe from this group, send email to [email protected]. For more options, visit this group at http://groups.google.com/group/open-iscsi?hl=en.
