I can not change the slot, I only have one slot (BladeServer),
--------------------------------------------------------------------
lspci -vvs 02:00.0 :
02:00.0 PCI bridge: Mellanox Technologies MT23108 PCI Bridge (rev a1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: e0000000-efffffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [70] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=2 Dev=0 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=512, Commitment Limit=512
: Downstream: Capacity=128, Commitment Limit=128
---------------------------------------------------------------------------------------------------
lspci -vvs 02:01.0
02:01.0 PCI bridge: Mellanox Technologies MT23108 PCI Bridge (rev a1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size 08
Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: e0000000-efffffff
Secondary status: 66Mhz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: [70] PCI-X bridge device.
Secondary Status: 64bit+, 133MHz+, SCD-, USC-, SCO-,
SRD- Freq=3
Status: Bus=2 Dev=1 Func=0 64bit+ 133MHz+ SCD- USC-,
SCO-, SRD-
: Upstream: Capacity=512, Commitment Limit=512
: Downstream: Capacity=128, Commitment Limit=128
-----------------------------------------------------------------------------------------------------
Thx
On Thu, 2005-09-15 at 08:50 -0700, Grant Grundler wrote:
On Thu, Sep 15, 2005 at 06:11:26PM +0800, QiWang, Chen wrote: > there are some diff: > 02:00.0 --> work > 02:01.0 --> failed > > and first time I install the ib-verbs on node1, It also failed, because > lspci= 02:01.0, an I don not know how i change 02:01.0 to 02:00.0, and > it works fine for me. You can only change it by removing the Mellanox card and re-installing in the other slot. Can you post "lspci -vvs 02:01.0" output from the machine that failed? Can you post "lspci -vvs 02:00.0" output from the machine that worked? grant
-- QiWang, Chen <[EMAIL PROTECTED]> Clustars Supercomputing Technology corp. http://www.Clustars.CN TEL:+86-0816-2546345-815 FAX:+86-0816-2546370 Mobile:+86-13096497499 |
_______________________________________________ openib-general mailing list [email protected] http://openib.org/mailman/listinfo/openib-general
To unsubscribe, please visit http://openib.org/mailman/listinfo/openib-general
