Hi, I'm not sure about your problem scope, But did you try running the following commands? (adds a CLM node(say PL-5) and a logical AMF node(PL-5) mapped to that CLM node) immcfg -c SaClmNode safNode=PL-5,safCluster=myClmCluster immcfg -c SaAmfNode -a saAmfNodeSuFailOverProb=1200000000000 -a saAmfNodeSuFailoverMax=2 -a saAmfNodeClmNode=safNode=PL-5,safCluster=myClmCluster safAmfNode=PL-5,safAmfCluster=myAmfCluster
immcfg helps you to create/modify/delete changes to the IMM model. Try immcfg --help Regards, Mathi. > -----Original Message----- > From: Greg Hurlman [mailto:[email protected]] > Sent: Friday, December 06, 2013 12:42 PM > To: Nivrutti Kale > Cc: [email protected] > Subject: Re: [users] Payload node addition > > Yes, all the payload nodes were running while expanding the cluster size > from 2 payload nodes to 3. Even I tried stopping the opensafd service in both > payload1 and paylod2. > > The content of the nodes.cfg are: > > Existing Nodes: > SC SC-1 sc-active > SC SC-2 sc-standby > PL PL-1 payload1 > PL PL-2 payload2 > > New Node Configuration added: > PL PL-3 payload3 > > Where, payload1, payload2 and payload3 are the host names for all the > payload nodes and sc-active, sc-standby are the host names of the controller > nodes. > > Thanks, > Greg > > > > > > On Thu, Dec 5, 2013 at 9:28 PM, Nivrutti Kale <[email protected]> wrote: > > > Hi Greg, > > > > Does all your existing nodes running when you are trying to expand the > > cluster? > > Also share the contents of nodes.cfg mentioning current and new nodes > > entry. > > > > Thanks & Regards, > > Nivrutti > > > > > > On Fri, Dec 6, 2013 at 4:04 AM, Greg Hurlman > <[email protected]>wrote: > > > >> Hi, > >> > >> > >> I followed the above mentioned steps to add dynamically a new payload > >> node while the existing payload nodes were running. And when I ran > >> the modify script after adding the entry in nodes.cfg, the below > >> error I am getting. Anybody faced similar issue before?? > >> > >> *[root@sc-active immxml]# ./immxml-modify-config* > >> *error: When expanding the cluster all existing nodes must be started > >> (saAmfNodeOperState=1). Exiting!* > >> > >> It did not reboot the payload nodes, neither it got added to the cluster. > >> Anything obvious I am missing here? > >> > >> Thanks, > >> Greg > >> > >> > >> On Wed, Dec 4, 2013 at 9:34 PM, Nivrutti Kale <[email protected]> > wrote: > >> > >>> Hi Greg, > >>> > >>> You can use the ./immxml-modify-config for adding new payload nodes > >>> to the running cluster without stopping the running controllers or > >>> payload nodes. > >>> > >>> Steps to run: > >>> > >>> 1. Add entries for newly added payload nodes in nodes.cfg > >>> 2. Run ./immxml-modify-config > >>> > >>> Hope that helps. > >>> > >>> Thanks & Regards, > >>> Nivrutti > >>> > >>> > >>> > >>> > >>> On Thu, Dec 5, 2013 at 6:37 AM, Greg Hurlman > <[email protected]>wrote: > >>> > >>>> Hi, > >>>> > >>>> I have a running cluster with 2 payload nodes created by using > >>>> > >>>> immxml-clustersize -s 2 -p 2 > >>>> > >>>> Can I dynamically add a new payload node to this running cluster > >>>> without stopping the running controllers or payload nodes? or What > >>>> is the best way to do so? Are there any workarounds if not > >>>> possible? > >>>> > >>>> Appreciate for any help. > >>>> > >>>> Thanks > >>>> Greg > >>>> > >>>> ------------------------------------------------------------------- > >>>> ----------- > >>>> Sponsored by Intel(R) XDK > >>>> Develop, test and display web and hybrid apps with a single code base. > >>>> Download it for free now! > >>>> > >>>> > http://pubads.g.doubleclick.net/gampad/clk?id=111408631&iu=/4140/os > >>>> tg.clktrk _______________________________________________ > >>>> Opensaf-users mailing list > >>>> [email protected] > >>>> https://lists.sourceforge.net/lists/listinfo/opensaf-users > >>>> > >>> > >>> > >> > > > ------------------------------------------------------------------------------ > Sponsored by Intel(R) XDK > Develop, test and display web and hybrid apps with a single code base. > Download it for free now! > http://pubads.g.doubleclick.net/gampad/clk?id=111408631&iu=/4140/ostg.cl > ktrk > _______________________________________________ > Opensaf-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/opensaf-users ------------------------------------------------------------------------------ Rapidly troubleshoot problems before they affect your business. Most IT organizations don't have a clear picture of how application performance affects their revenue. With AppDynamics, you get 100% visibility into your Java,.NET, & PHP application. Start your 15-day FREE TRIAL of AppDynamics Pro! http://pubads.g.doubleclick.net/gampad/clk?id=84349831&iu=/4140/ostg.clktrk _______________________________________________ Opensaf-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/opensaf-users
