Hi,
On Sat, May 14, 2016 at 05:51:19PM +0200, Thomas Bechtold wrote:
> Hi,
>
> I tried again the Cubox-i Tumbleweed image
> (openSUSE-Tumbleweed-ARM-JeOS-cuboxi.armv7l-2016.05.05-Build1.4.raw.xz )
> but it's broken again. This time, I get:
I booted from the wrong SD-Card. But it's still broken. The output is:
U-Boot SPL 2016.03 (Apr 08 2016 - 09:48:30)
Trying to boot from MMC
U-Boot 2016.03 (Apr 08 2016 - 09:48:30 +0000)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 36C
Reset cause: POR
Board: MX6 Cubox-i
DRAM: 2 GiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
2770 bytes read in 35 ms (77.1 KiB/s)
## Executing script at 12000000
switch to partitions #0, OK
mmc0 is current device
7283888 bytes read in 525 ms (13.2 MiB/s)
46639057 bytes read in 2858 ms (15.6 MiB/s)
38393 bytes read in 306 ms (122.1 KiB/s)
Kernel image @ 0x10800100 [ 0x000000 - 0x6f24b0 ]
## Loading init Ramdisk from Legacy Image at 14800100 ...
Image Name: Initrd
Image Type: ARM Linux RAMDisk Image (uncompressed)
Data Size: 46638993 Bytes = 44.5 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 14700100
Booting using the fdt blob at 0x14700100
Using Device Tree in place at 14700100, end 1470c6f8
Starting kernel ...
[ 0.226358] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 4.094720] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 4.101792] sr_init: platform driver register failed for SR
[ 4.121896] Unable to find PPMU node
setterm: cannot (un)set powersave mode: Inappropriate ioctl for device
[ 9.253948] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 9.261401] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 9.271195] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 9.294412] imx-gpc 20dc000.gpc: failed to get pu regulator: -517
[ 9.492090] etnaviv-gpu 2204000.gpu: hw init failed: -6
[ 9.924683] systemd-udevd[291]: ctx=0x7f7f3090
path=/lib/modules/4.5.3-1-defa
ult/kernel/drivers/net/wireless/broadcom/brcm80211/brcmutil/brcmutil.ko
error=No
such file or directory
[ 9.930775] systemd-udevd[294]: ctx=0x7f7f3090
path=/lib/modules/4.5.3-1-defa
ult/kernel/drivers/net/wireless/broadcom/brcm80211/brcmutil/brcmutil.ko
error=No
such file or directory
[ 169.028082] reboot: Restarting system
--
To unsubscribe, e-mail: [email protected]
To contact the owner, e-mail: [email protected]
