12.02.2020 20:58, ITwrx пишет: > On 2/12/20 11:56 AM, Matwey V. Kornilov wrote: >> 12.02.2020 18:37, ITwrx пишет: >>> On 2/12/20 8:59 AM, ITwrx wrote: >>>> On 2/12/20 1:49 AM, Matwey V. Kornilov wrote: >>>>> Hi, >>>>> >>>>> It is very strange to hear that. I deployed this image to couple of >>>>> Rock64-s week ago. >>>>> So, could you please be more specific? What are you trying to do exactly? >>>>> >>>>> You are supposed to download >>>>> openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw.xz >>>>> uncompress it with `xz -d >>>>> openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw.xz` >>>>> and write .raw file to microsd card as the following `dd_rescue >>>>> openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30-Build5.29.raw >>>>> /dev/your_sd_card_here`. >>>> That's what i did, but i'll try it again. I didn't get any errors when >>>> writing the image. This time, i'll wipe the sd card and create one fat >>>> partition, just to be on the safe side. >>>>> Do you have usb rs232 ttl converter to attach the Rock64 console? What >>>>> does it say? >>>> i did, but i don't remember. It didn't get very far. If it fails this >>>> time, i'll copy and paste the output. >>>> >>>> Thanks >>>> >>>>> ср, 12 февр. 2020 г. в 10:17, Guillaume Gardet <[email protected]>: >>>>>> Hi, >>>>>> >>>>>>> -----Original Message----- >>>>>>> From: ITwrx <[email protected]> >>>>>>> Sent: 12 February 2020 03:49 >>>>>>> To: [email protected] >>>>>>> Subject: [opensuse-arm] Rock64 >>>>>>> >>>>>>> Thorston/All, >>>>>>> >>>>>>> i just wanted to report that there are not Rock64 microOS images, only >>>>>>> images for >>>>>>> the older pine64. >>>>>>> >>>>>>> Also, the instructions on the Rock64 openSUSE wiki don't work (exactly >>>>>>> as they >>>>>>> are), using the below linked image file. I don't know what the >>>>>>> corresponding >>>>>>> "packages" file is for or how to use it, so it was not used in any way. >>>>>>> The Rock64 >>>>>> The "packages" file is just the list of installed packages in this >>>>>> *.raw.xz image. >>>>>> >>>>>>> openSUSE wiki page didn't mention anything about it. Probably why the >>>>>>> board >>>>>>> won't boot... :) >>>>>>> >>>>>>> http://download.opensuse.org/repositories/devel:/ARM:/Factory:/Contrib:/Roc >>>>>>> kchip/images/openSUSE-Tumbleweed-ARM-JeOS-rock64.aarch64-2020.01.30- >>>>>>> Build5.29.raw.xz >>>>>>> >>>>>>> Any tips appreciated. >>>>>> Added Matwey in Cc who may help. >>>>>> >>>>>> Cheers, >>>>>> Guillaume >>>>>> >>>>>>> Thanks, >>>>>>> >>>>>>> ITwrx >>>>>>> >>>>>>> >>>>>>> -- >>>>>>> To unsubscribe, e-mail: [email protected] >>>>>>> To contact the owner, e-mail: [email protected] >>> Ok, i misspoke earlier. The first time i didn't extract, then run >>> dd_rescue per your instructions. i ran "xzcat [image].raw.xz | dd bs=4M >>> of=/dev/sdX iflag=fullblock oflag=direct; sync" (substituting relevant >>> info) per the wiki. This time i did use your commands. I got the same >>> result and output in the serial console as before. >>> >>>> U-Boot TPL 2020.01 (Jan 30 2020 - 10:43:44) >>>> data training error >>>> col error >>>> data training error >>>> LPDDR3, 800MHz >>>> BW=16 Col=12 Bk=8 CS0 Row=16 CS=1 Die BW=8 Size=4096MB >>> I don't know much about Arm, so i don't know what that output means. :) >> It is very first stage of bootloader. Do you see anything else next? > no. That's where it stops, unfortunately. I guess i could try the ALARM > install process and see if it stops at the same point, in which case > maybe it's an hardware issue.
For me, the output looks like. (My testing board is 2GB, but I successfully use 4GB also) U-Boot TPL 2020.01 (Jan 30 2020 - 10:43:44) LPDDR3, 800MHz BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB Trying to boot from BOOTROM Returning to boot ROM... U-Boot SPL 2020.01 (Jan 30 2020 - 10:43:44 +0000) Trying to boot from MMC1 NOTICE: BL31: v2.1(debug): NOTICE: BL31: Built : 22:19:57, Sep 4 2019 ERROR: over or zero region, nr=4187432, max=10 NOTICE: BL31:Rockchip release version: v1.2 INFO: ARM GICv2 driver initialized INFO: plat_rockchip_pmu_init: pd status 0xe INFO: BL31: Initializing runtime services WARNING: BL31: cortex_a53: CPU workaround for 819472 was missing! WARNING: BL31: cortex_a53: CPU workaround for 824069 was missing! WARNING: BL31: cortex_a53: CPU workaround for 827319 was missing! WARNING: BL31: cortex_a53: CPU workaround for 855873 was missing! INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 Well, maybe something is still wrong with U-boot (It is known to be not quite stable for Rock64 at the time of 2019.10 release). Could you try this section? https://en.opensuse.org/HCL:Rock64#Using_proprietary_TPL_bootloader If the proprietary boot-loader works, then the issue should be reported to u-boot maillist. >> >>> Thanks >>> >>> >> > -- To unsubscribe, e-mail: [email protected] To contact the owner, e-mail: [email protected]
