Hello community,
here is the log from the commit of package raspberrypi-firmware for
openSUSE:Factory checked in at 2019-09-07 11:52:13
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Comparing /work/SRC/openSUSE:Factory/raspberrypi-firmware (Old)
and /work/SRC/openSUSE:Factory/.raspberrypi-firmware.new.7948 (New)
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Package is "raspberrypi-firmware"
Sat Sep 7 11:52:13 2019 rev:45 rq:728555 version:2019.09.04
Changes:
--------
---
/work/SRC/openSUSE:Factory/raspberrypi-firmware/raspberrypi-firmware-config.changes
2019-07-18 15:19:46.884150903 +0200
+++
/work/SRC/openSUSE:Factory/.raspberrypi-firmware.new.7948/raspberrypi-firmware-config.changes
2019-09-07 11:52:14.826284187 +0200
@@ -1,0 +2,65 @@
+Thu Sep 5 15:24:04 UTC 2019 - Guillaume GARDET <[email protected]>
+
+- Update to e2e17cd03 (2019-09-04)
+ * firmware: Port file loading revamp to master
+ * firmware: Avoid defaulting to 64-bit kernel on older Pi
+ * firmware: Revamp file loading logic
+ * firmware: power: Allow reading uncached voltage
+ * firmware: arm_loader: Request KMS to use CVT timings
+ * firmware: vc_image: Default YUVUV to non-tall mode, with flag if required
+ * firmware: ldconfig: Implement [pi2/pi3/pi3+] using board types
+ See: #1242
+ * firmware: platform: Remove 10mV of margin
+ * firmware: power: Add 2711-specific PMIC compensation values
+ * firmware: sdhost_arasan: Disable busy wait on EMMC_STATUS_NEW_CARD_DATA_SET
+ * firmware: AWB: Fix for manual WB settings in capture
+ See: #1215
+ * firmware: arm_loader: Use platform_get_min_core_voltage for actual min
voltage
+ * firmware: clock: Remember disable state across clock changes
+ * firmware: platform: pi4: Reduce min core voltage to 810mV
+ * firmware: arm_dt: Use boost to force turbo mode rather than modifying
core_freq_min for uart
+ * firmware: arm_loader: Add optional flag to add_boost and get_boost calls
+ * firmware: avs_2711: Move margin from init structure to run time
+ * firmware: platform: fix get_min_default
+ * firmware: arm_loader: Use AP_CLOCK_T for clock_iterator for easier
debugging
+ * hdmi: Switch to active pixel rate + margin for core clock boost
+ * platform: Reduce the minimum core clock frequency from 250 to 200 MHz
+ * firmware: arm_loader: Fix initial_turbo getting stuck
+ See: #1005
+ * firmware: clock_2711: don't set reserved values for KA in PLL KAIP
registers
+ * firmware: AWB: Allow user to set manual gains for the RPi algorithm
+ * firmware: arm_loader: Fix disabling of audio before reboot
+ * firmware: fixed up the custom CVT values to use correct group
+ * firmware: hdmi: Add independent table entries for hdmi_timings on each
display
+ See: #1218
+ * firmware: Fix to allow HDMI audio port route setting
+ See: raspberrypi/linux#3100
+ * firmware: pwm_audio: Use the correct DREQs on Pi4
+ See: #1214
+ * firmware: pixelvalve_2711: Alter back porch for widths of 1366
+ See: #1202
+ * firmware: Clear the SMIDSW1 display interrupt flag on startup
+ * firmware: dt-blob: Declare Pi 4B's SD_IO voltage selector
+ * firmware: Fixups for missing code changes from Pi4 branch
+ See: #1201
+ * firmware: Change order of display remapping for default display number
+ * firmware: AWB: Set default number of stats regions for RPi AWB
+ See: #1198
+ * firmware: Fix composite interrupt HVS channel
+ * firmware: scalarlib: Fix width setting for SCALERLIB_PIXEL_FORMAT_YUV10COL
+ * firmware: vcmailbox: Add a new SET_AUDIO_LDO_STATE mailbox command
+ * firmware: Add mailbox call to report the HDMI timings
+ * firmware: H264: Set the decoder cache AXI burst length to the same as the
encoder
+ * firmware: gencmd: Fix gencmd max result length
+ * firmware: bootloader_config: New gencmd to read the EEPROM config
+ * firmware: pwm_audio: Use PWM1 on BCM2838 unless remapped
+ See: #1178
+ * firmware: AWB updates
+ See: #1167
+ * firmware: dispmanx: Fix handling of disable_overscan to not disable it
totally
+ See: raspberrypi/linux#3059
+ * firmware: power: Enable/disable H264 and ISP clocks with domain
+ * firmware: arm_loader: arm_64bit=0 should disable loading of kernel8.img
+ * firmware: dt-blob: CM has no activity LED
+
+-------------------------------------------------------------------
raspberrypi-firmware.changes: same change
Old:
----
raspberrypi-firmware-2019.07.09.tar.bz2
New:
----
raspberrypi-firmware-2019.09.04.tar.bz2
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
Other differences:
------------------
++++++ raspberrypi-firmware-config.spec ++++++
--- /var/tmp/diff_new_pack.XimADO/_old 2019-09-07 11:52:16.626283932 +0200
+++ /var/tmp/diff_new_pack.XimADO/_new 2019-09-07 11:52:16.630283931 +0200
@@ -17,7 +17,7 @@
Name: raspberrypi-firmware-config
-Version: 2019.07.09
+Version: 2019.09.04
Release: 0
Summary: Configuration for the Raspberry Pi firmware loader
License: MIT
++++++ raspberrypi-firmware.spec ++++++
--- /var/tmp/diff_new_pack.XimADO/_old 2019-09-07 11:52:16.646283930 +0200
+++ /var/tmp/diff_new_pack.XimADO/_new 2019-09-07 11:52:16.646283930 +0200
@@ -17,7 +17,7 @@
Name: raspberrypi-firmware
-Version: 2019.07.09
+Version: 2019.09.04
Release: 0
Summary: Binary bootloader and firmware files for Raspberry Pi
License: SUSE-Firmware
++++++ raspberrypi-firmware-2019.07.09.tar.bz2 ->
raspberrypi-firmware-2019.09.04.tar.bz2 ++++++
/work/SRC/openSUSE:Factory/raspberrypi-firmware/raspberrypi-firmware-2019.07.09.tar.bz2
/work/SRC/openSUSE:Factory/.raspberrypi-firmware.new.7948/raspberrypi-firmware-2019.09.04.tar.bz2
differ: char 11, line 1
