Since upgrading to 10.3 I've not been able to burn CD's (DVD's are fine), I've tried this on several machines all with the same problem, didn't have problems on earlier versions of SUSE..
I tried installing cdrecord which enabled me to write CD's via the command line but K3B is still broken. From the command line wodim gives me: wodim -v -eject speed=16 driveropts=burnproof dev=/dev/scd1 ~/cd.iso wodim: No write mode specified. wodim: Asuming -tao mode. wodim: Future versions of wodim may have different drive dependent defaults. TOC Type: 1 = CD-ROM scsidev: '/dev/scd1' devname: '/dev/scd1' scsibus: -2 target: -2 lun: -2 Linux sg driver version: 3.5.27 Wodim version: 1.1.6 Driveropts: 'burnproof' SCSI buffer size: 64512 Device type : Removable CD-ROM Version : 5 Response Format: 2 Capabilities : Vendor_info : 'ATAPI ' Identification : 'CD-R/RW 24X10 ' Revision : 'P.MJ' Device seems to be: Generic mmc CD-RW. Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr). Driver flags : MMC SWABAUDIO BURNFREE Supported modes: TAO PACKET SAO RAW/R16 RAW/R96R Drive buf size : 1630208 = 1592 KB Beginning DMA speed test. Set CDR_NODMATEST environment variable if device communication breaks or freezes immediately after that. FIFO size : 4194304 = 4096 KB Track 01: data 188 MB Total size: 217 MB (21:30.24) = 96768 sectors Lout start: 217 MB (21:32/18) = 96768 sectors Current Secsize: 2048 ATIP info from disk: Indicated writing power: 4 Is not unrestricted Is not erasable Disk sub type: Medium Type C, low Beta category (C-) (6) ATIP start of lead in: -11559 (97:27/66) ATIP start of lead out: 359846 (79:59/71) Disk type: Short strategy type (Phthalocyanine or similar) Manuf. index: 21 Manufacturer: Ricoh Company Limited Blocks total: 359846 Blocks current: 359846 Blocks remaining: 263078 Speed set to 2816 KB/s Starting to write CD/DVD at speed 16.0 in real TAO mode for single session. Last chance to quit, starting real write i 0 seconds. Operation starts. Waiting for reader process to fill input buffer ... input buffer ready. Performing OPC... Starting new track at sector: 0 Track 01: 1 of 188 MB written (fifo 100%) [buf 66%] 0.9x.Errno: 5 (Input/ output error), write_g1 scsi sendcmd: no error CDB: 2A 00 00 00 03 07 00 00 1F 00 status: 0x2 (CHECK CONDITION) Sense Bytes: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF Sense Key: 0xF Reserved, Segment 255 Sense Code: 0xFF Qual 0xFF (vendor unique sense code 0xFF) [No matching qualifie r] Fru 0xFF Sense flags: Blk -1 (valid) file mark detected end of medium illegal block lengt h cmd finished after 1.602s timeout 40s write track data: error after 1587200 bytes wodim: A write error occured. wodim: Please properly read the error message above. Writing time: 19.116s Average write speed 67.6x. Fixating... Fixating time: 44.059s wodim: fifo had 89 puts and 26 gets. wodim: fifo was 0 times empty and 14 times full, min fill was 92%. Thought about uninstalling all the CD/DVD packages and then installing the ones from 10.2 but if there's a simpler solution then it would be helpful. Regards Matthew -- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
