I'm not sure what you mean for not getting the wifi running, but make sure
the "network" config option is present and correctly set:
config wifi-iface 'wifinet1'
# ,,,
option network 'lan'
It's used to bridge the wifi interface to the lan.
For the rest, I don't see failures in the log, nor the renaming of unnamed
configurations should affect the configuration, therefore I think is just
something missing in the resulting configuration.
On Fri, Jul 31, 2020 at 6:39 PM Mirza Arnaut <[email protected]>
wrote:
> Okay, I cloned my template add the custom setting under wireless.
> Now the existing config is overwritten with the new one!
> But I'm still not able to get the WiFi running...
>
> Running *wifi* leads to the following log entries:
> [ 257.774066] br-lan: port 2(wlan0) entered disabled state
> [ 257.787418] br-lan: port 3(wlan1) entered disabled state
> [ 257.805638] device wlan0 left promiscuous mode
> [ 257.810269] br-lan: port 2(wlan0) entered disabled state
> [ 257.816028] {natflow}:natflow_netdev_event(): catch NETDEV_UNREGISTER
> event for dev=wlan0
> [ 257.837096] device wlan1 left promiscuous mode
> [ 257.841727] br-lan: port 3(wlan1) entered disabled state
> [ 257.847552] {natflow}:natflow_netdev_event(): catch NETDEV_UNREGISTER
> event for dev=wlan1
> [ 259.938533] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 259.944622] warning: (zone_netdev_event:346)dev=wlan0 set zone=127 type
> =0
> [ 259.951631] {natflow}:natflow_netdev_event(): catch NETDEV_UP event for
> dev=wlan0, add ingress hook
> [ 260.025806] br-lan: port 2(wlan0) entered blocking state
> [ 260.031337] br-lan: port 2(wlan0) entered disabled state
> [ 260.037173] device wlan0 entered promiscuous mode
> [ 260.074672] device wlan0 left promiscuous mode
> [ 260.079442] br-lan: port 2(wlan0) entered disabled state
> [ 260.210068] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self
> calibration start
> [ 260.218932] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self
> calibration end
> [ 262.170478] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT
> Calibration Done!
> [ 262.183350] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration
> Start!
> [ 262.204705] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done
> ! CH = 0, (gain= f, phase=3e)
> [ 262.214948] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration
> Start!
> [ 262.236269] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done
> ! CH = 1, (gain= 0, phase=3e)
> [ 262.245629] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ
> Calibration Done!
> [ 262.269762] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=
> 0, Ph_rx=4
> [ 262.287666] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=
> 3, Ph_rx=-7
> [ 262.305219] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
> [ 262.311350] warning: (zone_netdev_event:346)dev=wlan1 set zone=127 type
> =0
> [ 262.318314] {natflow}:natflow_netdev_event(): catch NETDEV_UP event for
> dev=wlan1, add ingress hook
> [ 262.340749] br-lan: port 2(wlan1) entered blocking state
> [ 262.346329] br-lan: port 2(wlan1) entered disabled state
> [ 262.352147] device wlan1 entered promiscuous mode
> [ 262.364186] device wlan1 left promiscuous mode
> [ 262.368962] br-lan: port 2(wlan1) entered disabled state
> [ 262.517909] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
> [ 262.524028] warning: (zone_netdev_event:346)dev=wlan0 set zone=127 type
> =0
> [ 262.530964] {natflow}:natflow_netdev_event(): catch NETDEV_UP event for
> dev=wlan0, add ingress hook
> [ 262.633854] br-lan: port 2(wlan0) entered blocking state
> [ 262.639291] br-lan: port 2(wlan0) entered disabled state
> [ 262.645194] device wlan0 entered promiscuous mode
> [ 262.968331] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self
> calibration start
> [ 262.977168] ieee80211 phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self
> calibration end
> [ 264.845365] ieee80211 phy1: rt2800_loft_iq_calibration: Info - LOFT
> Calibration Done!
> [ 264.858254] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration
> Start!
> [ 264.879623] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done
> ! CH = 0, (gain= 0, phase=3e)
> [ 264.889874] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration
> Start!
> [ 264.911227] ieee80211 phy1: rt2800_iq_search: Info - IQCalibration Done
> ! CH = 1, (gain= f, phase= 0)
> [ 264.920599] ieee80211 phy1: rt2800_loft_iq_calibration: Info - TX IQ
> Calibration Done!
> [ 264.944751] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=
> 0, Ph_rx=5
> [ 264.962670] ieee80211 phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=
> 3, Ph_rx=-7
> [ 264.978551] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready
> [ 264.984667] warning: (zone_netdev_event:346)dev=wlan1 set zone=127 type
> =0
> [ 264.991666] {natflow}:natflow_netdev_event(): catch NETDEV_UP event for
> dev=wlan1, add ingress hook
> [ 265.091744] br-lan: port 3(wlan1) entered blocking state
> [ 265.097260] br-lan: port 3(wlan1) entered disabled state
> [ 265.103215] device wlan1 entered promiscuous mode
>
> I also noticed something on the first openwisp start, which I do not
> remember having in the normal OpenWRT version:
> Sat Aug 1 07:35:29 2020 daemon.info openwisp: Local configuration
> outdated
> Sat Aug 1 07:35:29 2020 daemon.info openwisp: Downloading configuration
> from controller...
> Sat Aug 1 07:35:29 2020 daemon.info openwisp: Configuration downloaded,
> now applying it...
> Sat Aug 1 07:35:30 2020 daemon.info openwisp: The following uci configs
> have been renamed: base_config.status1, dhcp.dnsmasq1, dropbear.dropbear1,
> firewall.defaults, firewall.zone1, firewall.zone2, firewall.forwarding1,
> firewall.rule1, firewall.rule2, firewall.rule3, firewall.rule4, firewall.
> rule5, firewall.rule6, firewall.rule7, firewall.rule8, firewall.rule9,
> firewall.rule10, firewall.include1, ksmbd.globals1, p910nd.p910nd1, pptpd.
> login1, rpcd.rpcd1, rpcd.login2, ucitrack.network1, ucitrack.wireless1,
> ucitrack.firewall1, ucitrack.olsr1, ucitrack.dhcp1, ucitrack.odhcpd1,
> ucitrack.dropbear2, ucitrack.httpd1, ucitrack.fstab1, ucitrack.qos1,
> ucitrack.system1, ucitrack.luci_splash1, ucitrack.ntpclient1, ucitrack.
> samba1, ucitrack.tinyproxy1, ucitrack.macvlan1, ucitrack.wizard1, ucitrack
> .xwan1, ucitrack.upnpd1, ucitrack.p910nd2, ucitrack.sqm1, ucitrack.
> natcapd1, upnpd.perm_rule1, upnpd.perm_rule2, xwan.xwan2, network.switch0,
> network.switch0_vlan1, network.switch0_vlan2, fstab.global1, system.system
> , ubootenv.ubootenv1
> Sat Aug 1 07:35:31 2020 daemon.info openwisp: Service base_config has
> been reloaded via procd/ubus
> Sat Aug 1 07:35:31 2020 daemon.info openwisp: Service dhcp has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:31 2020 daemon.info openwisp: Service dropbear has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:31 2020 daemon.info openwisp: Service firewall has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:32 2020 daemon.info openwisp: Service fstab has been
> reloaded via init.d script
> Sat Aug 1 07:35:32 2020 daemon.info openwisp: Service ksmbd has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:32 2020 daemon.info openwisp: Service natcapd has been
> reloaded via init.d script
> Sat Aug 1 07:35:32 2020 daemon.info openwisp: Service network has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:32 2020 daemon.info openwisp: Service p910nd has been
> reloaded via init.d script
> Sat Aug 1 07:35:33 2020 daemon.info openwisp: Service pptpd has been
> reloaded via init.d script
> Sat Aug 1 07:35:33 2020 daemon.info openwisp: Service rpcd has been
> reloaded via init.d script
> Sat Aug 1 07:35:33 2020 daemon.info openwisp: Service system has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:34 2020 daemon.info openwisp: Service ubootenv has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:34 2020 daemon.info openwisp: Service ucitrack has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:34 2020 daemon.info openwisp: Service upnpd has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:34 2020 daemon.info openwisp: Service wireless has been
> reloaded via procd/ubus
> Sat Aug 1 07:35:34 2020 daemon.info openwisp: Service xwan has been
> reloaded via init.d script
>
>
>
> On Saturday, August 1, 2020 at 1:08:55 AM UTC+2, Federico Capoano wrote:
>>
>> Look at this:
>> https://github.com/openwisp/netjsonconfig/blob/master/tests/openwrt/test_wireless.py#L947-L975
>>
>> See "arbitrary_id"? Add the same attribute but put wlan0 and wlan1 to the
>> respective interface and the existing interfaces should be replaced.
>>
>> Ups, seems this is not documented :(
>>
>> http://netjsonconfig.openwisp.org/en/latest/backends/openwrt.html#wireless-settings
>>
>> Let me know if it solves your problem.
>>
>> F.
>>
>> On Fri, Jul 31, 2020 at 5:35 PM Mirza Arnaut <[email protected]> wrote:
>>
>>> Hello Federico,
>>>
>>> When I boot it after running *firstboot* the following config is
>>> present:
>>>
>>> */etc/config/network*
>>> *config interface 'loopback'*
>>> * option ifname 'lo'*
>>> * option proto 'static'*
>>> * option ipaddr '127.0.0.1'*
>>> * option netmask '255.0.0.0'*
>>>
>>> *config globals 'globals'*
>>> * option ula_prefix 'fd00:a5a0:8fe0::/48'*
>>> * option packet_steering '1'*
>>>
>>> *config interface 'lan'*
>>> * option type 'bridge'*
>>> * option ifname 'eth0.1'*
>>> * option proto 'static'*
>>> * option ipaddr '192.168.15.1'*
>>> * option netmask '255.255.255.0'*
>>> * option ip6assign '60'*
>>>
>>> *config device 'lan_eth0_1_dev'*
>>> * option name 'eth0.1'*
>>> * option macaddr '7a:11:dc:1b:1a:63'*
>>>
>>> *config interface 'wan'*
>>> * option ifname 'eth0.2'*
>>> * option proto 'dhcp'*
>>>
>>> *config device 'wan_eth0_2_dev'*
>>> * option name 'eth0.2'*
>>> * option macaddr '78:11:dc:1b:1a:63'*
>>>
>>> *config interface 'wan6'*
>>> * option ifname 'eth0.2'*
>>> * option proto 'dhcpv6'*
>>>
>>> *config switch*
>>> * option name 'switch0'*
>>> * option reset '1'*
>>> * option enable_vlan '1'*
>>>
>>> *config switch_vlan*
>>> * option device 'switch0'*
>>> * option vlan '1'*
>>> * option ports '1 4 6t'*
>>>
>>> *config switch_vlan*
>>> * option device 'switch0'*
>>> * option vlan '2'*
>>> * option ports '0 6t'*
>>>
>>> *config interface 'usbwan'*
>>> * option proto 'dhcp'*
>>> * option ifname 'usb0'*
>>> * option metric '800'*
>>>
>>> */etc/config/wireless*
>>> *config wifi-device 'radio0'*
>>> * option type 'mac80211'*
>>> * option hwmode '11a'*
>>> * option path 'pci0000:00/0000:00:00.0/0000:01:00.0'*
>>> * option htmode 'VHT80'*
>>> * option disabled '0'*
>>> * option country 'CN'*
>>> * option txpower 'auto'*
>>> * option channel 'auto'*
>>>
>>> *config wifi-device 'radio1'*
>>> * option type 'mac80211'*
>>> * option hwmode '11g'*
>>> * option path 'platform/10180000.wmac'*
>>> * option htmode 'HT20'*
>>> * option disabled '0'*
>>> * option country 'CN'*
>>> * option txpower 'auto'*
>>> * option channel 'auto'*
>>>
>>> *config wifi-iface 'wifinet0'*
>>> * option device 'radio0'*
>>> * option network 'lan'*
>>> * option mode 'ap'*
>>> * option ssid 'X-WRT_1A63'*
>>> * option encryption 'psk2'*
>>> * option skip_inactivity_poll '1'*
>>> * option wpa_group_rekey '0'*
>>> * option wpa_pair_rekey '0'*
>>> * option wpa_master_rekey '0'*
>>> * option key '88888888'*
>>>
>>> *config wifi-iface 'wifinet1'*
>>> * option device 'radio1'*
>>> * option network 'lan'*
>>> * option mode 'ap'*
>>> * option ssid 'X-WRT_1A63'*
>>> * option encryption 'psk2'*
>>> * option skip_inactivity_poll '1'*
>>> * option wpa_group_rekey '0'*
>>> * option wpa_pair_rekey '0'*
>>> * option wpa_master_rekey '0'*
>>> * option key '88888888'*
>>>
>>> After installing openwisp and connecting it I get the following configs:
>>>
>>> */etc/config/network*
>>>
>>>
>>>
>>> *... (same as above)config interface 'wlan1' option auto '1'
>>> option enabled '1' option ifname 'wlan1' option mtu '1500'
>>> option proto 'none'config interface 'wlan0' option auto '1'
>>> option enabled '1' option ifname 'wlan0' option mtu
>>> '1500' option proto 'none'*
>>>
>>> */etc/config/wireless*
>>>
>>>
>>>
>>> *... (same as above)config wifi-iface 'wifi_wlan0' option device
>>> 'radio0' option disabled '0' option encryption 'psk2'
>>> option hidden '0' option ifname 'wlan0' option isolate '0'
>>> option key 'test1234' option macfilter 'disable' option
>>> mode 'ap' option ssid 'Narouter' option wds '0' option
>>> wmm '1'config wifi-iface 'wifi_wlan1' option device 'radio1'
>>> option disabled '0' option encryption 'psk2' option hidden
>>> '0' option ifname 'wlan1' option isolate '0' option
>>> key 'test1234' option macfilter 'disable' option mode 'ap'
>>> option ssid 'Narouter' option wds '0' option wmm '1'*
>>>
>>> The log after running *wifi* is:
>>> Sat Aug 1 00:28:05 2020 daemon.notice netifd: radio0 (12042): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:05 2020 daemon.notice netifd: radio1 (12043): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.779600] br-lan: port
>>> 2(wlan0) entered disabled state
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.796972] br-lan: port
>>> 3(wlan1) entered disabled state
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.820131] device wlan0
>>> left promiscuous mode
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.824690] br-lan: port
>>> 2(wlan0) entered disabled state
>>> Sat Aug 1 00:28:05 2020 kern.warn kernel: [ 418.830516]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UNREGISTER event for
>>> dev=wlan0
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.847009] device wlan1
>>> left promiscuous mode
>>> Sat Aug 1 00:28:05 2020 kern.info kernel: [ 418.851649] br-lan: port
>>> 3(wlan1) entered disabled state
>>> Sat Aug 1 00:28:05 2020 kern.warn kernel: [ 418.857420]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UNREGISTER event for
>>> dev=wlan1
>>> Sat Aug 1 00:28:07 2020 daemon.notice netifd: radio0 (12085): sh:
>>> acs_survey: out of range
>>> Sat Aug 1 00:28:07 2020 daemon.notice netifd: radio0 (12085): sh:
>>> acs_survey: out of range
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: Configuration file:
>>> /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.374436] IPv6:
>>> ADDRCONF(NETDEV_UP): wlan0: link is not ready
>>> Sat Aug 1 00:28:08 2020 kern.warn kernel: [ 421.380582] warning:
>>> (zone_netdev_event:346)dev=wlan0 set zone=127 type=0
>>> Sat Aug 1 00:28:08 2020 kern.warn kernel: [ 421.387524]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UP event for dev=wlan0, add
>>> ingress hook
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.475438] br-lan: port
>>> 2(wlan0) entered blocking state
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.480990] br-lan: port
>>> 2(wlan0) entered disabled state
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.486804] device wlan0
>>> entered promiscuous mode
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: ctrl_iface exists and
>>> seems to be in use - cannot override it
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: Delete
>>> '/var/run/hostapd/wlan0' manually if it is not used anymore
>>> Sat Aug 1 00:28:08 2020 daemon.err hostapd: Failed to setup control
>>> interface for wlan0
>>> Sat Aug 1 00:28:08 2020 daemon.err hostapd: wlan0: Unable to setup
>>> interface.
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: nl80211: deinit
>>> ifname=wlan0 disabled_11b_rates=0
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.518082] device wlan0
>>> left promiscuous mode
>>> Sat Aug 1 00:28:08 2020 kern.info kernel: [ 421.522872] br-lan: port
>>> 2(wlan0) entered disabled state
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: wlan0:
>>> CTRL-EVENT-TERMINATING
>>> Sat Aug 1 00:28:08 2020 daemon.err hostapd: hostapd_free_hapd_data:
>>> Interface wlan0 wasn't started
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: wlan0:
>>> CTRL-EVENT-TERMINATING
>>> Sat Aug 1 00:28:08 2020 daemon.err hostapd: hostapd_free_hapd_data:
>>> Interface wlan0 wasn't started
>>> Sat Aug 1 00:28:08 2020 daemon.notice netifd: radio0 (12085): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:08 2020 daemon.notice hostapd: Configuration file:
>>> /var/run/hostapd-phy1.conf (phy wlan1) --> new PHY
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 421.632090] ieee80211
>>> phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 421.640920] ieee80211
>>> phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
>>> Sat Aug 1 00:28:10 2020 daemon.notice netifd: radio0 (12085): WARNING
>>> (wireless_add_process): executable path /usr/sbin/wpad does not match
>>> process path (/proc/exe)
>>> Sat Aug 1 00:28:10 2020 daemon.notice netifd: radio0 (12085): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.614783] ieee80211
>>> phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.627667] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Start!
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.649021] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 1,
>>> phase=3f)
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.659264] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Start!
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.680586] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= f,
>>> phase=3e)
>>> Sat Aug 1 00:28:10 2020 kern.info kernel: [ 423.689946] ieee80211
>>> phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.714003] ieee80211
>>> phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=1, Ph_rx=5
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.731908] ieee80211
>>> phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=3, Ph_rx=-7
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.749495] IPv6:
>>> ADDRCONF(NETDEV_UP): wlan1: link is not ready
>>> Sat Aug 1 00:28:11 2020 kern.warn kernel: [ 423.755627] warning:
>>> (zone_netdev_event:346)dev=wlan1 set zone=127 type=0
>>> Sat Aug 1 00:28:11 2020 kern.warn kernel: [ 423.762585]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UP event for dev=wlan1, add
>>> ingress hook
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.781021] br-lan: port
>>> 2(wlan1) entered blocking state
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.786460] br-lan: port
>>> 2(wlan1) entered disabled state
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.792358] device wlan1
>>> entered promiscuous mode
>>> Sat Aug 1 00:28:11 2020 daemon.notice hostapd: ctrl_iface exists and
>>> seems to be in use - cannot override it
>>> Sat Aug 1 00:28:11 2020 daemon.notice hostapd: Delete
>>> '/var/run/hostapd/wlan1' manually if it is not used anymore
>>> Sat Aug 1 00:28:11 2020 daemon.err hostapd: Failed to setup control
>>> interface for wlan1
>>> Sat Aug 1 00:28:11 2020 daemon.err hostapd: wlan1: Unable to setup
>>> interface.
>>> Sat Aug 1 00:28:11 2020 daemon.notice hostapd: nl80211: deinit
>>> ifname=wlan1 disabled_11b_rates=0
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.801095] device wlan1
>>> left promiscuous mode
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.805878] br-lan: port
>>> 2(wlan1) entered disabled state
>>> Sat Aug 1 00:28:11 2020 daemon.notice hostapd: wlan1:
>>> CTRL-EVENT-TERMINATING
>>> Sat Aug 1 00:28:11 2020 daemon.err hostapd: hostapd_free_hapd_data:
>>> Interface wlan1 wasn't started
>>> Sat Aug 1 00:28:11 2020 daemon.notice hostapd: wlan1:
>>> CTRL-EVENT-TERMINATING
>>> Sat Aug 1 00:28:11 2020 daemon.err hostapd: hostapd_free_hapd_data:
>>> Interface wlan1 wasn't started
>>> Sat Aug 1 00:28:11 2020 daemon.notice netifd: radio1 (12084): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:11 2020 daemon.notice netifd: radio1 (12084): WARNING
>>> (wireless_add_process): executable path /usr/sbin/wpad does not match
>>> process path (/proc/exe)
>>> Sat Aug 1 00:28:11 2020 daemon.notice netifd: radio1 (12084): Command
>>> failed: Invalid argument
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 423.965955] IPv6:
>>> ADDRCONF(NETDEV_UP): wlan0: link is not ready
>>> Sat Aug 1 00:28:11 2020 kern.warn kernel: [ 423.972088] warning:
>>> (zone_netdev_event:346)dev=wlan0 set zone=127 type=0
>>> Sat Aug 1 00:28:11 2020 kern.warn kernel: [ 423.979359]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UP event for dev=wlan0, add
>>> ingress hook
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 424.143854] br-lan: port
>>> 2(wlan0) entered blocking state
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 424.149363] br-lan: port
>>> 2(wlan0) entered disabled state
>>> Sat Aug 1 00:28:11 2020 kern.info kernel: [ 424.155265] device wlan0
>>> entered promiscuous mode
>>> Sat Aug 1 00:28:13 2020 kern.info kernel: [ 424.455727] ieee80211
>>> phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration start
>>> Sat Aug 1 00:28:13 2020 kern.info kernel: [ 424.464588] ieee80211
>>> phy1: rt2800_rf_self_txdc_cal: Info - RF Tx self calibration end
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.353880] ieee80211
>>> phy1: rt2800_loft_iq_calibration: Info - LOFT Calibration Done!
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.366676] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Start!
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.388038] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 0, (gain= 0,
>>> phase=3e)
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.398294] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Start!
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.419641] ieee80211
>>> phy1: rt2800_iq_search: Info - IQCalibration Done! CH = 1, (gain= 0,
>>> phase=3e)
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.429035] ieee80211
>>> phy1: rt2800_loft_iq_calibration: Info - TX IQ Calibration Done!
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.453232] ieee80211
>>> phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=0, Ph_rx=5
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.471156] ieee80211
>>> phy1: rt2800_rxiq_calibration: Info - RXIQ G_imb=3, Ph_rx=-7
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.487074] IPv6:
>>> ADDRCONF(NETDEV_UP): wlan1: link is not ready
>>> Sat Aug 1 00:28:14 2020 kern.warn kernel: [ 426.493204] warning:
>>> (zone_netdev_event:346)dev=wlan1 set zone=127 type=0
>>> Sat Aug 1 00:28:14 2020 kern.warn kernel: [ 426.500212]
>>> {natflow}:natflow_netdev_event(): catch NETDEV_UP event for dev=wlan1, add
>>> ingress hook
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.663688] br-lan: port
>>> 3(wlan1) entered blocking state
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.669180] br-lan: port
>>> 3(wlan1) entered disabled state
>>> Sat Aug 1 00:28:14 2020 kern.info kernel: [ 426.675135] device wlan1
>>> entered promiscuous mode
>>>
>>> I hope I will be able to set it up, since I really like the idea behind
>>> your tool!
>>>
>>> Best regards
>>> M
>>>
>>>
>>> On Friday, July 31, 2020 at 5:08:25 PM UTC+2, Federico Capoano wrote:
>>>>
>>>> Hi Mirza,
>>>>
>>>> could you please share the configuration in /etc/config/wireless and
>>>> the relevant error output of logread after you run the command "wifi" or
>>>> "reload_config" (the latter works only after changing the wireless
>>>> configuration).
>>>>
>>>> F.
>>>>
>>>> On Fri, Jul 31, 2020 at 4:25 AM Mirza Arnaut <[email protected]>
>>>> wrote:
>>>>
>>>>> I wanted to try using OpenWRT for my Xiaomi Routers, but found out,
>>>>> that the Mi WiFi R3 is not officially supported. But I found out, that the
>>>>> Chinese fork, called X-WRT has images for it, hence I used it, thinking
>>>>> that not much would be changed in the image.
>>>>> Now I have a Redmi AC2100 which works perfectly with OpenWisp, so does
>>>>> the R3 for basic configurations (Timezone, Hostnam, etc.).
>>>>> Since I am a lazy person, I wanted to make a 2.4 and 5 GHz network and
>>>>> apply it on both of them, but it fails to do so on the X-WRT router.
>>>>> Has someone successfully got it working? I suppose the config
>>>>> differences are causing this behaviour, since the default name for wifi
>>>>> interfaces are not wifi_wlanX but wifinetX for example.
>>>>> Thanks in advance!
>>>>>
>>>>> --
>>>>> You received this message because you are subscribed to the Google
>>>>> Groups "OpenWISP" group.
>>>>> To unsubscribe from this group and stop receiving emails from it, send
>>>>> an email to [email protected].
>>>>> To view this discussion on the web, visit
>>>>> https://groups.google.com/d/msgid/openwisp/c63b10e4-6980-4c46-907c-c2be01384d46n%40googlegroups.com
>>>>> <https://groups.google.com/d/msgid/openwisp/c63b10e4-6980-4c46-907c-c2be01384d46n%40googlegroups.com?utm_medium=email&utm_source=footer>
>>>>> .
>>>>>
>>>> --
>>> You received this message because you are subscribed to the Google
>>> Groups "OpenWISP" group.
>>> To unsubscribe from this group and stop receiving emails from it, send
>>> an email to [email protected].
>>> To view this discussion on the web, visit
>>> https://groups.google.com/d/msgid/openwisp/b23c1464-38f4-4283-be35-b4506500061do%40googlegroups.com
>>> <https://groups.google.com/d/msgid/openwisp/b23c1464-38f4-4283-be35-b4506500061do%40googlegroups.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>> --
> You received this message because you are subscribed to the Google Groups
> "OpenWISP" group.
> To unsubscribe from this group and stop receiving emails from it, send an
> email to [email protected].
> To view this discussion on the web, visit
> https://groups.google.com/d/msgid/openwisp/41d9396a-e282-4e87-819e-9cfbf7d9d692o%40googlegroups.com
> <https://groups.google.com/d/msgid/openwisp/41d9396a-e282-4e87-819e-9cfbf7d9d692o%40googlegroups.com?utm_medium=email&utm_source=footer>
> .
>
--
You received this message because you are subscribed to the Google Groups
"OpenWISP" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion on the web, visit
https://groups.google.com/d/msgid/openwisp/CAERYH6UFBSp%3DFTaUNY-ko6n3MyonPqn6%2BqjrS%3DzuKQZaa3xAyA%40mail.gmail.com.
