Support for Belkin F5D8235-4 v1 (RT288x) works: - switch - buttons - some leds
does not work: - USB (not supported by RT288XX) - WLAN Based on r29397 Signed-off-by: Cezary Jackiewicz <[email protected]> --- --- target/linux/ramips/rt288x/config-2.6.39 +++ target/linux/ramips/rt288x/config-2.6.39 @@ -92,6 +92,7 @@ CONFIG_RALINK_RT288X=y # CONFIG_RALINK_RT305X is not set CONFIG_RAMIPS_WDT=y +CONFIG_RT288X_MACH_F5D8235_V1=y CONFIG_RT288X_MACH_RT_N15=y CONFIG_RT288X_MACH_WZR_AGL300NH=y CONFIG_RTL8366S_PHY=y --- target/linux/ramips/rt288x/profiles/belkin.mk +++ target/linux/ramips/rt288x/profiles/belkin.mk @@ -0,0 +1,18 @@ +# +# Copyright (C) 2011 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/F5D8235V1 + NAME:=Belkin F5D8235 V1 + PACKAGES:=kmod-switch-rtl8366s kmod-swconfig swconfig +endef + +define Profile/F5D8235_V1/Description + Package set for Belkin F5D8235 V1 +endef + +$(eval $(call Profile,F5D8235V1)) + --- target/linux/ramips/files/arch/mips/ralink/rt288x/Kconfig +++ target/linux/ramips/files/arch/mips/ralink/rt288x/Kconfig @@ -2,6 +2,10 @@ menu "Ralink RT288x machine selection" +config RT288X_MACH_F5D8235_V1 + bool "Belkin F5D8235 V1 board support" + select RALINK_DEV_GPIO_LEDS + config RT288X_MACH_RT_N15 bool "Asus RT-N15 board support" select RALINK_DEV_GPIO_BUTTONS --- target/linux/ramips/files/arch/mips/ralink/rt288x/devices.c +++ target/linux/ramips/files/arch/mips/ralink/rt288x/devices.c @@ -56,6 +56,21 @@ .num_resources = ARRAY_SIZE(rt288x_flash1_resources), }; +static struct resource rt288x_flash8_resources[] = { + { + .flags = IORESOURCE_MEM, + .start = KSEG1ADDR(RT2880_FLASH0_BASE), + .end = KSEG1ADDR(RT2880_FLASH0_BASE) + + RT2880_FLASH8_SIZE - 1, + }, +}; + +static struct platform_device rt288x_flash8_device = { + .name = "physmap-flash", + .resource = rt288x_flash8_resources, + .num_resources = ARRAY_SIZE(rt288x_flash8_resources), +}; + static int rt288x_flash_instance __initdata; void __init rt288x_register_flash(unsigned int id, struct physmap_flash_data *pdata) @@ -73,6 +88,10 @@ pdev = &rt288x_flash1_device; reg = MEMC_REG_FLASH_CFG1; break; + case 8: + pdev = &rt288x_flash8_device; + reg = MEMC_REG_FLASH_CFG0; + break; default: return; } --- target/linux/ramips/files/arch/mips/ralink/rt288x/mach-f5d8235-v1.c +++ target/linux/ramips/files/arch/mips/ralink/rt288x/mach-f5d8235-v1.c @@ -0,0 +1,142 @@ +/* + * Belkin F5D825 V1 board support + * + * Copyright (C) 2011 Cezary Jackiewicz <[email protected]> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/mtd/mtd.h> +#include <linux/mtd/partitions.h> +#include <linux/mtd/physmap.h> + +#include <asm/mach-ralink/machine.h> +#include <asm/mach-ralink/dev-gpio-buttons.h> +#include <asm/mach-ralink/dev-gpio-leds.h> +#include <asm/mach-ralink/rt288x.h> +#include <asm/mach-ralink/rt288x_regs.h> + +#include "devices.h" + +#include <linux/rtl8366.h> +#include <linux/ethtool.h> + +#include <asm/mach-ralink/ramips_eth_platform.h> + +#define F5D8235_GPIO_RTL8366_SCK 2 +#define F5D8235_GPIO_RTL8366_SDA 1 + +#define F5D8235_GPIO_LED_USB_BLUE 7 +#define F5D8235_GPIO_LED_USB_ORANGE 8 +#define F5D8235_GPIO_BUTTON_WPS 0 +#define F5D8235_GPIO_BUTTON_RESET 9 + +#define F5D8235_BUTTONS_POLL_INTERVAL 20 + +#ifdef CONFIG_MTD_PARTITIONS +static struct mtd_partition f5d8235_partitions[] = { + { + .name = "uboot", + .offset = 0, + .size = 0x050000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "kernel and rootfs", + .offset = 0x050000, + .size = 0x790000, + }, { + .name = "rootfs", + .offset = 0x1D0000, + .size = 0x610000, + }, { + .name = "nvram", + .offset = 0x7E0000, + .size = 0x010000, + }, { + .name = "factory", + .offset = 0x7F0000, + .size = 0x010000, + } +}; +#endif /* CONFIG_MTD_PARTITIONS */ + +static struct physmap_flash_data f5d8235_flash_data = { +#ifdef CONFIG_MTD_PARTITIONS + .nr_parts = ARRAY_SIZE(f5d8235_partitions), + .parts = f5d8235_partitions, +#endif +}; + +static struct rtl8366_platform_data f5d8235_rtl8366s_data = { + .gpio_sda = F5D8235_GPIO_RTL8366_SDA, + .gpio_sck = F5D8235_GPIO_RTL8366_SCK, +}; + +static struct platform_device f5d8235_rtl8366s_device = { + .name = RTL8366S_DRIVER_NAME, + .id = -1, + .dev = { + .platform_data = &f5d8235_rtl8366s_data, + } +}; + +static struct gpio_led f5d8235_leds_gpio[] __initdata = { + { + .name = "f5d8234-v1:blue:storage", + .gpio = F5D8235_GPIO_LED_USB_BLUE, + .active_low = 1, + },{ + .name = "f5d8234-v1:orange:storage", + .gpio = F5D8235_GPIO_LED_USB_ORANGE, + .active_low = 1, + } +}; + +static struct gpio_button f5d8235_gpio_buttons[] __initdata = { + { + .desc = "reset", + .type = EV_KEY, + .code = KEY_RESTART, + .threshold = 3, + .gpio = F5D8235_GPIO_BUTTON_RESET, + .active_low = 1, + }, { + .desc = "wps", + .type = EV_KEY, + .code = KEY_WPS_BUTTON, + .threshold = 3, + .gpio = F5D8235_GPIO_BUTTON_WPS, + .active_low = 1, + } +}; + +static void __init f5d8235_init(void) +{ + rt288x_gpio_init(RT2880_GPIO_MODE_UART0 | RT2880_GPIO_MODE_I2C); + + rt288x_register_flash(8, &f5d8235_flash_data); + rt288x_register_wifi(); + rt288x_register_wdt(); + + ramips_register_gpio_leds(-1, ARRAY_SIZE(f5d8235_leds_gpio), + f5d8235_leds_gpio); + + ramips_register_gpio_buttons(-1, F5D8235_BUTTONS_POLL_INTERVAL, + ARRAY_SIZE(f5d8235_gpio_buttons), + f5d8235_gpio_buttons); + + platform_device_register(&f5d8235_rtl8366s_device); + + rt288x_eth_data.speed = SPEED_1000; + rt288x_eth_data.duplex = DUPLEX_FULL; + rt288x_eth_data.tx_fc = 1; + rt288x_eth_data.rx_fc = 1; + rt288x_register_ethernet(); +} + +MIPS_MACHINE(RAMIPS_MACH_F5D8235_V1, "F5D8235_V1", + "Belkin F5D8235 v1", f5d8235_init); --- target/linux/ramips/files/arch/mips/ralink/rt288x/Makefile +++ target/linux/ramips/files/arch/mips/ralink/rt288x/Makefile @@ -13,6 +13,9 @@ obj-$(CONFIG_EARLY_PRINTK) += early_printk.o +obj-$(CONFIG_RT288X_MACH_F5D8235_V1) += mach-f5d8235-v1.o + obj-$(CONFIG_RT288X_MACH_RT_N15) += mach-rt-n15.o obj-$(CONFIG_RT288X_MACH_WZR_AGL300NH) += mach-wzr-agl300nh.o + --- target/linux/ramips/files/arch/mips/include/asm/mach-ralink/rt288x_regs.h +++ target/linux/ramips/files/arch/mips/include/asm/mach-ralink/rt288x_regs.h @@ -39,6 +39,7 @@ #define RT2880_UART0_SIZE 0x100 #define RT2880_PIO_SIZE 0x100 #define RT2880_UART1_SIZE 0x100 +#define RT2880_FLASH8_SIZE (8 * 1024 * 1024) #define RT2880_FLASH1_SIZE (16 * 1024 * 1024) #define RT2880_FLASH0_SIZE (4 * 1024 * 1024) --- target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h +++ target/linux/ramips/files/arch/mips/include/asm/mach-ralink/machine.h @@ -14,6 +14,7 @@ enum ramips_mach_type { RAMIPS_MACH_GENERIC, /* RT2880 based machines */ + RAMIPS_MACH_F5D8235_V1, /* Belkin F5D8235 v1 */ RAMIPS_MACH_RT_N15, /* Asus RT-N15 */ RAMIPS_MACH_WZR_AGL300NH, /* Buffalo WZR-AGL300NH */ --- target/linux/ramips/image/Makefile (wersja 29397) +++ target/linux/ramips/image/Makefile (kopia robocza) @@ -229,7 +229,11 @@ $(call Image/Build/Template/F5D8235V2,$(1),f5d8235v2,F5D8235_V2) endef +define Image/Build/Template/F5D8235V1 + $(call BuildFirmware/Generic,$(1),$(2),board=$(3),mtdlayout_f5d8235,$(mtd_f5d8235_kernel_part_size),$(mtd_f5d8235_rootfs_part_size)) +endef + mtdlayout_wr5123gn=mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,832k(kernel),2944k(rootfs),3776k@0x50000(firmware) mtdlayout_wr5123gn8m=mtdparts=physmap-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,832k(kernel),7040k(rootfs),7872k@0x50000(firmware) define Image/Build/Profile/WR5123GN @@ -237,7 +241,6 @@ $(call BuildFirmware/Generic,$(1),wr512-3gn-8M,board="WR512-3GN",mtdlayout_wr5123gn8m,851968,7208960) endef - ifeq ($(CONFIG_RALINK_RT305X),y) define Image/Build/Profile/Default $(call Image/Build/Profile/ARGUS_ATP52B,$(1)) @@ -258,6 +261,9 @@ endef endif +define Image/Build/Profile/F5D8235V1 + $(call Image/Build/Template/F5D8235V1,$(1),f5d8235v1,F5D8235_V1) +endef define Image/Build/Profile/RTN15 $(call Image/Build/Template/GENERIC_4M,$(1),rt-n15,RT-N15) @@ -265,6 +271,7 @@ ifeq ($(CONFIG_RALINK_RT288X),y) define Image/Build/Profile/Default + $(call Image/Build/Profile/F5D8235V1,$(1)) $(call Image/Build/Profile/RTN15,$(1)) endef endif --- target/linux/ramips/base-files/lib/ramips.sh +++ target/linux/ramips/base-files/lib/ramips.sh @@ -25,6 +25,9 @@ *"DIR-600 B2") name="dir-600-b2" ;; + *"F5D8235 v1") + name="f5d8235-v1" + ;; *"F5D8235 v2") name="f5d8235-v2" ;; --- target/linux/ramips/base-files/etc/uci-defaults/leds +++ target/linux/ramips/base-files/etc/uci-defaults/leds @@ -22,6 +22,9 @@ bc2) set_usb_led "bc2:blue:usb" ;; + f5d8235-v1) + set_usb_led "f5d8235-v1:green:usb" + ;; fonera20n) set_usb_led "fonera20n:amber:usb" ;; --- target/linux/ramips/base-files/etc/uci-defaults/network +++ target/linux/ramips/base-files/etc/uci-defaults/network @@ -56,6 +56,7 @@ ucidef_set_interfaces_lan_wan "eth0.1 eth0.2" ;; + f5d8235-v1 | \ rt-n15) ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" ucidef_add_switch "rtl8366s" "1" "1" @@ -88,6 +89,7 @@ argus-atp52b | \ b2c | \ + f5d8235-v1 | \ nw718 | \ rt-n15) lan_mac=$(get_mac_binary factory 4) _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
