Got problem with pci on P-2812HNU-F1, it was simply not initialized (missing whole pci part in bootlog), I've added target/linux/lantiq/xrx200/config-3.18 from config-3.14(changed only UBI_GLUEBI to UBI_BLOCK), and pci went back, not sure how build config is generated but that solved my problem. VDSL Annex A is working atm, if anything regarding stability will happen I'll post an update.
Best Regards / Pozdrawiam Sylwester Petela / ScApi W dniu 2015-02-10 o 19:39, John Crispin pisze: > > On 10/02/2015 19:35, Joerg Hollmann wrote: >> Hello Daniel, >> >> could it be, that the definition of the kernel partition in the dts >> file of your device ist too small? > i think the problem is that spi-gpio is either not loaded or loaded > too late. i wont have time to look at it till friday though. > >> I have seen similar error messages on the builds for the VG3503J. > there is a kernel part defined in the dts ? the mtdsplit should handle > it for your. i'll look at that aswell, only tested a initramfs on the > VG3503J > > John > >> Regards, Joerg >> >> On 02/10/2015 10:40 AM, Daniel Gimpelevich wrote: >>> Is there a patchset I could try? >>> >>> On Mon, 2015-02-09 at 12:44 -0800, Daniel Gimpelevich wrote: >>>> On Mon, 2015-02-09 at 21:27 +0100, John Crispin wrote: >>>>> bootlog please >>>>> >>>>> On 09/02/2015 21:25, Daniel Gimpelevich wrote: >>>>>> On Mon, 2015-02-09 at 19:18 +0100, John Crispin wrote: >>>>>>> try r44366 or newer please >>>>>> SPI flash is not detected, bricking the device. >>>>>> >>>> [ 0.000000] Linux version 3.18.6 (danielg4@chimera) (gcc >>>> version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r43982) ) #3 Mon >>>> Feb 9 115 [ 0.000000] SoC: AR9 rev 1.2 [ 0.000000] >>>> bootconsole [early0] enabled [ 0.000000] CPU0 revision is: >>>> 0001954c (MIPS 34Kc) [ 0.000000] MIPS: machine is DGN3500 - >>>> Netgear DGN3500 [ 0.000000] Determined physical RAM map: [ >>>> 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] >>>> User-defined physical RAM map: [ 0.000000] memory: 04000000 >>>> @ 00000000 (usable) [ 0.000000] Initrd not found or empty - >>>> disabling initrd [ 0.000000] Zone ranges: [ 0.000000] >>>> Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable >>>> zone start for each node [ 0.000000] Early memory node >>>> ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ >>>> 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ >>>> 0.000000] Primary instruction cache 32kB, VIPT, 4-way, >>>> linesize 32 bytes. [ 0.000000] Primary data cache 16kB, >>>> 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built >>>> 1 zonelists in Zone order, mobility grouping on. Total pages: >>>> 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock0 >>>> ip=192.168.1.1:192.168.1.15::::eth0:on console=ttyS1,115200 >>>> ethaddr=30:46:90 [ 0.000000] PID hash table entries: 256 >>>> (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table >>>> entries: 8192 (order: 3, 32768 bytes) [ 0.000000] >>>> Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ >>>> 0.000000] Writing ErrCtl register=00005880 [ 0.000000] >>>> Readback ErrCtl register=00005880 [ 0.000000] Memory: >>>> 60404K/65536K available (3312K kernel code, 147K rwdata, 664K >>>> rodata, 144K init, 194K bss, 5132K reserved) [ 0.000000] >>>> NR_IRQS:256 [ 0.000000] CPU Clock: 333MHz [ 0.000000] >>>> Calibrating delay loop... 221.18 BogoMIPS (lpj=442368) [ >>>> 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] >>>> Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ >>>> 0.044000] Mountpoint-cache hash table entries: 1024 (order: 0, >>>> 4096 bytes) [ 0.052000] pinctrl core: initialized pinctrl >>>> subsystem [ 0.056000] NET: Registered protocol family 16 [ >>>> 0.064000] pinctrl-xway 1e100b10.pinmux: Init done [ >>>> 0.068000] dma-xway 1e104100.dma: Init done - hw rev: 6, ports: >>>> 5, channels: 20 [ 0.076000] PCI host bridge >>>> /fpi@10000000/pci@E105400 ranges: [ 0.080000] MEM >>>> 0x0000000018000000..0x0000000019ffffff [ 0.084000] IO >>>> 0x000000001ae00000..0x000000001affffff [ 0.088000] >>>> ath9k,eeprom ath9k_eep: failed to load eeprom address [ >>>> 0.100000] usbcore: registered new interface driver usbfs [ >>>> 0.104000] usbcore: registered new interface driver hub [ >>>> 0.108000] usbcore: registered new device driver usb [ >>>> 0.112000] PCI host bridge to bus 0000:00 [ 0.116000] pci_bus >>>> 0000:00: root bus resource [mem 0x18000000-0x19ffffff] [ >>>> 0.120000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ >>>> 0.124000] pci_bus 0000:00: No busn resource found for root >>>> bus, will use [bus 00-ff] [ 0.128000] pci 0000:00:0e.0: BAR >>>> 0: assigned [mem 0x18000000-0x1800ffff] [ 0.132000] Switched >>>> to clocksource MIPS [ 0.136000] NET: Registered protocol >>>> family 2 [ 0.144000] TCP established hash table entries: >>>> 1024 (order: 0, 4096 bytes) [ 0.148000] TCP bind hash table >>>> entries: 1024 (order: 0, 4096 bytes) [ 0.156000] TCP: Hash >>>> tables configured (established 1024 bind 1024) [ 0.164000] >>>> TCP: reno registered [ 0.164000] UDP hash table entries: 256 >>>> (order: 0, 4096 bytes) [ 0.172000] UDP-Lite hash table >>>> entries: 256 (order: 0, 4096 bytes) [ 0.180000] NET: >>>> Registered protocol family 1 [ 0.184000] gptu: totally 6 >>>> 16-bit timers/counters [ 0.188000] gptu: misc_register on >>>> minor 63 [ 0.192000] gptu: succeeded to request irq 126 [ >>>> 0.196000] gptu: succeeded to request irq 127 [ 0.200000] >>>> gptu: succeeded to request irq 128 [ 0.204000] gptu: >>>> succeeded to request irq 129 [ 0.212000] gptu: succeeded to >>>> request irq 130 [ 0.216000] gptu: succeeded to request irq >>>> 131 [ 0.220000] futex hash table entries: 256 (order: -1, >>>> 3072 bytes) [ 0.228000] squashfs: version 4.0 (2009/01/31) >>>> Phillip Lougher [ 0.236000] jffs2: version 2.2 (NAND) >>>> (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red >>>> Hat, Inc. [ 0.248000] msgmni has been set to 117 [ >>>> 0.252000] io scheduler noop registered [ 0.256000] io >>>> scheduler deadline registered (default) [ 0.260000] >>>> 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, >>>> base_baud = 0) is a lantiq,asc [ 0.268000] console [ttyLTQ0] >>>> enabled [ 0.268000] console [ttyLTQ0] enabled [ 0.276000] >>>> bootconsole [early0] disabled [ 0.276000] bootconsole >>>> [early0] disabled [ 0.332000] Realtek RTL8366RB ethernet >>>> switch driver version 0.2.4 [ 0.340000] rtl8366rb rtl8366rb: >>>> using GPIO pins 491 (SDA) and 493 (SCK) [ 0.344000] >>>> rtl8366rb rtl8366rb: RTL5937 ver. 3 chip found [ 0.440000] >>>> libphy: rtl8366rb: probed [ 0.444000] libphy: ltq_mii: >>>> probed [ 0.444000] eth0 (uninitialized): no PHY found [ >>>> 0.452000] etop: mdio probe failed [ 0.456000] wdt >>>> 1f8803f0.watchdog: Init done [ 0.460000] TCP: cubic >>>> registered [ 0.464000] NET: Registered protocol family 17 [ >>>> 0.468000] bridge: automatic filtering via arp/ip/ip6tables has >>>> been deprecated. Update your scripts to load br_netfilter if >>>> yo. [ 0.480000] 8021q: 802.1Q VLAN Support v1.8 [ >>>> 0.484000] ath9k,eeprom ath9k_eep: failed to load eeprom >>>> address [ 0.496000] UBIFS error (pid 1): ubifs_mount: cannot >>>> open "ubi0:rootfs", error -19 [ 0.504000] VFS: Cannot open >>>> root device "mtdblock5" or unknown-block(0,0): error -6 [ >>>> 0.508000] Please append a correct "root=" boot option; here >>>> are the available partitions: [ 0.516000] Kernel panic - not >>>> syncing: VFS: Unable to mount root fs on unknown-block(0,0) [ >>>> 0.516000] Rebooting in 1 seconds.. >>> _______________________________________________ openwrt-devel >>> mailing list [email protected] >>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>> >> _______________________________________________ openwrt-devel >> mailing list [email protected] >> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >> > _______________________________________________ > openwrt-devel mailing list > [email protected] > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel > _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
