On Sun, 2015-02-15 at 20:49 +0100, John Crispin wrote: > Hi, > > i just pushed the v3.18 support for ar71xx. i have tested this on > carambola2, unifi and wndr4300. the default is still at 3.14. please > start testing on more hardware. > > to do so you need to set the kernel to 3.18 in > target/linux/ar71xx/Makefile as the default is still at 3.14. > > 902-unaligned_access_hacks.patch was rebased, however there might be new > places in the stack that need the hack applied. testing for this is also > welcome. > > John > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
Compiled just fine here on wndr3700v4. Sysupgraded my router via LuCI and immediately noticed two things: 1. no wifi [ 21.670000] cfg80211: Calling CRDA to update world regulatory domain [ 21.670000] cfg80211: World regulatory domain updated: [ 21.680000] cfg80211: DFS Master region: unset [ 21.680000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 21.690000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 21.700000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 21.710000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 21.720000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 21.730000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 21.730000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 21.740000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 21.750000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 22.170000] ath9k ar934x_wmac: Direct firmware load for soc_wmac.eeprom failed with error -2 [ 22.180000] ath: phy0: Unable to load EEPROM file soc_wmac.eeprom [ 22.190000] ath9k ar934x_wmac: failed to initialize device [ 22.190000] ath9k: probe of ar934x_wmac failed with error -22 [ 22.200000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 22.220000] ath9k 0000:00:00.0: Direct firmware load for pci_wmac0.eeprom failed with error -2 [ 22.230000] ath: phy1: Unable to load EEPROM file pci_wmac0.eeprom [ 22.230000] ath9k 0000:00:00.0: Failed to initialize device [ 22.240000] ath9k: probe of 0000:00:00.0 failed with error -22 [ 29.760000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready 2. bridge warning bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. regular ethX ports (lan side) work fine over wire. _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel