Hi 1 comment inline
On 08/11/2015 07:08, Shonn Lu wrote: > Signed-off-by: Shonn Lu <[email protected]> > --- > target/linux/ramips/base-files/etc/board.d/01_leds | 5 + > .../linux/ramips/base-files/etc/board.d/02_network | 1 + > target/linux/ramips/base-files/lib/ramips.sh | 3 + > .../ramips/base-files/lib/upgrade/platform.sh | 1 + > target/linux/ramips/dts/Youku-YK1.dts | 127 > +++++++++++++++++++++ > target/linux/ramips/image/Makefile | 2 + > 6 files changed, 139 insertions(+) > create mode 100644 target/linux/ramips/dts/Youku-YK1.dts > > diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds > b/target/linux/ramips/base-files/etc/board.d/01_leds > index 545bd70..bc86bd3 100755 > --- a/target/linux/ramips/base-files/etc/board.d/01_leds > +++ b/target/linux/ramips/base-files/etc/board.d/01_leds > @@ -261,6 +261,11 @@ case $board in > zte-q7) > set_wifi_led "zte:blue:status" > ;; > + yk1) > + ucidef_set_led_default "power" "power" "youku:blue:power" "1" > + set_wifi_led "youku:blue:air" > + set_usb_led "youku:blue:usb" > + ;; > esac > > board_config_flush > diff --git a/target/linux/ramips/base-files/etc/board.d/02_network > b/target/linux/ramips/base-files/etc/board.d/02_network > index 19ef3f7..3c87971 100755 > --- a/target/linux/ramips/base-files/etc/board.d/02_network > +++ b/target/linux/ramips/base-files/etc/board.d/02_network > @@ -145,6 +145,7 @@ ramips_setup_interfaces() > wsr-1166 | \ > wt1520 | \ > xiaomi-miwifi-mini |\ > + yk1 |\ > y1) > ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" > ucidef_add_switch "switch0" "1" "1" > diff --git a/target/linux/ramips/base-files/lib/ramips.sh > b/target/linux/ramips/base-files/lib/ramips.sh > index a9a6664..bdd6d4e 100755 > --- a/target/linux/ramips/base-files/lib/ramips.sh > +++ b/target/linux/ramips/base-files/lib/ramips.sh > @@ -409,6 +409,9 @@ ramips_board_detect() { > *"ZTE Q7") > name="zte-q7" > ;; > + *"Youku YK1") > + name="yk1" > + ;; > *"Lenovo Y1") > name="y1" the patch applies to a trunk prior to our cleanup. the patch wont apply because of this. please rebase it on current trunk and resend John > ;; > diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh > b/target/linux/ramips/base-files/lib/upgrade/platform.sh > index 11fee85..66fcd04 100755 > --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh > +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh > @@ -127,6 +127,7 @@ platform_check_image() { > y1 |\ > y1s |\ > zte-q7 |\ > + yk1 |\ > zbt-wa05) > [ "$magic" != "27051956" ] && { > echo "Invalid image type." > diff --git a/target/linux/ramips/dts/Youku-YK1.dts > b/target/linux/ramips/dts/Youku-YK1.dts > new file mode 100644 > index 0000000..10662d3 > --- /dev/null > +++ b/target/linux/ramips/dts/Youku-YK1.dts > @@ -0,0 +1,127 @@ > +/dts-v1/; > + > +/include/ "mt7620a.dtsi" > + > +/ { > + compatible = "Youku-YK1", "ralink,mt7620a-soc"; > + model = "Youku YK1"; > + > + palmbus@10000000 { > + > + gpio0: gpio@600 { > + status = "okay"; > + }; > + > + gpio1: gpio@638 { > + status = "okay"; > + }; > + > + gpio2: gpio@660 { > + status = "okay"; > + }; > + > + gpio3: gpio@688 { > + status = "okay"; > + }; > + > + spi@b00 { > + status = "okay"; > + > + m25p80@0 { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "w25q256"; > + reg = <0 0>; > + linux,modalias = "m25p80", "w25q256"; > + spi-max-frequency = <10000000>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x0 0x30000>; > + read-only; > + }; > + > + partition@30000 { > + label = "u-boot-env"; > + reg = <0x30000 0x10000>; > + read-only; > + }; > + > + factory: partition@40000 { > + label = "factory"; > + reg = <0x40000 0x10000>; > + read-only; > + }; > + > + partition@50000 { > + label = "firmware"; > + reg = <0x50000 0x1fb0000>; > + }; > + }; > + }; > + }; > + > + pinctrl { > + state_default: pinctrl0 { > + default { > + ralink,group = "i2c", "uartf", "rgmii1", > "rgmii2", "ephy", "wled", "nd_sd"; > + ralink,function = "gpio"; > + }; > + }; > + }; > + > + ethernet@10100000 { > + pinctrl-names = "default"; > + pinctrl-0 = <&ephy_pins>; > + mtd-mac-address = <&factory 0x4>; > + ralink,port-map = "llllw"; > + }; > + > + wmac@10180000 { > + ralink,mtd-eeprom = <&factory 0>; > + }; > + > + sdhci@b0130000 { > + status = "okay"; > + }; > + > + ehci@101c0000 { > + status = "okay"; > + }; > + > + ohci@101c1000 { > + status = "okay"; > + }; > + > + gpio-leds { > + compatible = "gpio-leds"; > + wan { > + label = "youku:blue:wan"; > + gpios = <&gpio2 4 1>; > + }; > + air { > + label = "youku:blue:air"; > + gpios = <&gpio3 0 1>; > + }; > + usb { > + label = "youku:blue:usb"; > + gpios = <&gpio1 11 1>; > + }; > + power { > + label = "youku:blue:power"; > + gpios = <&gpio1 5 1>; > + }; > + }; > + > + gpio-keys-polled { > + compatible = "gpio-keys-polled"; > + #address-cells = <1>; > + #size-cells = <0>; > + poll-interval = <20>; > + reset { > + label = "reset"; > + gpios = <&gpio0 1 1>; > + linux,code = <0x198>; > + }; > + }; > +}; > diff --git a/target/linux/ramips/image/Makefile > b/target/linux/ramips/image/Makefile > index b4d0897..ca320d3 100644 > --- a/target/linux/ramips/image/Makefile > +++ b/target/linux/ramips/image/Makefile > @@ -884,6 +884,7 @@ Image/Build/Profile/WRTNODE=$(call > BuildFirmware/Default16M/$(1),$(1),wrtnode,WR > Image/Build/Profile/WT3020=$(call > BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020) > Image/Build/Profile/XIAOMI-MIWIFI-MINI=$(call > BuildFirmware/Default16M/$(1),$(1),xiaomi-miwifi-mini,XIAOMI-MIWIFI-MINI) > Image/Build/Profile/ZTE-Q7=$(call > BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7) > +Image/Build/Profile/Youku-YK1=$(call > BuildFirmware/Default32M/$(1),$(1),youku-yk1,Youku-YK1) > Image/Build/Profile/ZBT-WA05=$(call > BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05) > Image/Build/Profile/ArcherC20i=$(call > BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i) > microwrt_mtd_size=16515072 > @@ -917,6 +918,7 @@ define Image/Build/Profile/Default > $(call Image/Build/Profile/WT3020,$(1)) > $(call Image/Build/Profile/XIAOMI-MIWIFI-MINI,$(1)) > $(call Image/Build/Profile/ZTE-Q7,$(1)) > + $(call Image/Build/Profile/Youku-YK1,$(1)) > $(call Image/Build/Profile/ZBT-WA05,$(1)) > $(call Image/Build/Profile/ArcherC20i,$(1)) > $(call Image/Build/Profile/MicroWRT,$(1)) > _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
