Hi,
you need to add the version info to you patches and the change history.
as in add [PATCH V3] if it is version 3 and inside the description add text
Changes since V2:
* change A
...
John
On 23/11/2015 08:08, Shonn Lu wrote:
> Signed-off-by: Shonn Lu <[email protected]>
> ---
> target/linux/ramips/base-files/etc/board.d/01_leds | 5 +
> .../linux/ramips/base-files/etc/board.d/02_network | 3 +-
> target/linux/ramips/base-files/lib/ramips.sh | 3 +
> .../ramips/base-files/lib/upgrade/platform.sh | 3 +-
> target/linux/ramips/dts/YOUKU-YK1.dts | 127
> +++++++++++++++++++++
> target/linux/ramips/image/Makefile | 2 +
> 6 files changed, 141 insertions(+), 2 deletions(-)
> create mode 100644 target/linux/ramips/dts/YOUKU-YK1.dts
>
> diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> index 5627c8c..1c18ded 100755
> --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> @@ -268,6 +268,11 @@ zbt-wr8305rt)
> zte-q7)
> set_wifi_led "$board:blue:status"
> ;;
> +youku-yk1)
> + ucidef_set_led_default "power" "power" "$board:blue:power" "1"
> + set_wifi_led "$board:blue:air"
> + set_usb_led "$board:blue:usb"
> + ;;
> esac
>
> board_config_flush
> diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> index 3821742..22809d1 100755
> --- a/target/linux/ramips/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> @@ -84,7 +84,8 @@ ramips_setup_interfaces()
> wsr-600|\
> wt1520|\
> y1|\
> - zbt-wg2626)
> + zbt-wg2626|\
> + youku-yk1)
> ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2"
> ucidef_add_switch "switch0" "1" "1"
> ucidef_add_switch_vlan "switch0" "1" "0 1 2 3 6t"
> diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> index a1bcb72..d6fdeb9 100755
> --- a/target/linux/ramips/base-files/lib/ramips.sh
> +++ b/target/linux/ramips/base-files/lib/ramips.sh
> @@ -460,6 +460,9 @@ ramips_board_detect() {
> *"ZBT-WR8305RT")
> name="zbt-wr8305rt"
> ;;
> + *"YK1")
> + name="youku-yk1"
> + ;;
> *)
> name="generic"
> ;;
> diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> index 0e8d619..0b9dd43 100755
> --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> @@ -134,7 +134,8 @@ platform_check_image() {
> zbt-wa05|\
> zbt-wg2626|\
> zbt-wr8305rt|\
> - zte-q7)
> + zte-q7|\
> + youku-yk1)
> [ "$magic" != "27051956" ] && {
> echo "Invalid image type."
> return 1
> diff --git a/target/linux/ramips/dts/YOUKU-YK1.dts
> b/target/linux/ramips/dts/YOUKU-YK1.dts
> new file mode 100644
> index 0000000..418351c
> --- /dev/null
> +++ b/target/linux/ramips/dts/YOUKU-YK1.dts
> @@ -0,0 +1,127 @@
> +/dts-v1/;
> +
> +/include/ "mt7620a.dtsi"
> +
> +/ {
> + compatible = "YOUKU-YK1", "ralink,mt7620a-soc";
> + model = "YOUKU YK1";
> +
> + palmbus@10000000 {
> +
> + gpio0: gpio@600 {
> + status = "okay";
> + };
> +
> + gpio1: gpio@638 {
> + status = "okay";
> + };
> +
> + gpio2: gpio@660 {
> + status = "okay";
> + };
> +
> + gpio3: gpio@688 {
> + status = "okay";
> + };
> +
> + spi@b00 {
> + status = "okay";
> +
> + m25p80@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "w25q256";
> + reg = <0 0>;
> + linux,modalias = "m25p80", "w25q256";
> + spi-max-frequency = <10000000>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition@30000 {
> + label = "u-boot-env";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + factory: partition@40000 {
> + label = "factory";
> + reg = <0x40000 0x10000>;
> + read-only;
> + };
> +
> + partition@50000 {
> + label = "firmware";
> + reg = <0x50000 0x1fb0000>;
> + };
> + };
> + };
> + };
> +
> + pinctrl {
> + state_default: pinctrl0 {
> + default {
> + ralink,group = "i2c", "uartf", "rgmii1",
> "rgmii2", "ephy", "wled", "nd_sd";
> + ralink,function = "gpio";
> + };
> + };
> + };
> +
> + ethernet@10100000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ephy_pins>;
> + mtd-mac-address = <&factory 0x4>;
> + ralink,port-map = "llllw";
> + };
> +
> + wmac@10180000 {
> + ralink,mtd-eeprom = <&factory 0>;
> + };
> +
> + sdhci@b0130000 {
> + status = "okay";
> + };
> +
> + ehci@101c0000 {
> + status = "okay";
> + };
> +
> + ohci@101c1000 {
> + status = "okay";
> + };
> +
> + gpio-leds {
> + compatible = "gpio-leds";
> + wan {
> + label = "youku-yk1:blue:wan";
> + gpios = <&gpio2 4 1>;
> + };
> + air {
> + label = "youku-yk1:blue:air";
> + gpios = <&gpio3 0 1>;
> + };
> + usb {
> + label = "youku-yk1:blue:usb";
> + gpios = <&gpio1 11 1>;
> + };
> + power {
> + label = "youku-yk1:blue:power";
> + gpios = <&gpio1 5 1>;
> + };
> + };
> +
> + gpio-keys-polled {
> + compatible = "gpio-keys-polled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + poll-interval = <20>;
> + reset {
> + label = "reset";
> + gpios = <&gpio0 1 1>;
> + linux,code = <0x198>;
> + };
> + };
> +};
> diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> index 5e19c3f..aced9c7 100644
> --- a/target/linux/ramips/image/Makefile
> +++ b/target/linux/ramips/image/Makefile
> @@ -900,6 +900,7 @@ Image/Build/Profile/WRTNODE=$(call
> BuildFirmware/Default16M/$(1),$(1),wrtnode,WR
> Image/Build/Profile/WT3020=$(call
> BuildFirmware/PorayDualSize/$(1),$(1),wt3020,WT3020)
> Image/Build/Profile/MIWIFI-MINI=$(call
> BuildFirmware/Default16M/$(1),$(1),miwifi-mini,MIWIFI-MINI)
> Image/Build/Profile/ZTE-Q7=$(call
> BuildFirmware/Default8M/$(1),$(1),zte-q7,ZTE-Q7)
> +Image/Build/Profile/YOUKU-YK1=$(call
> BuildFirmware/Default16M/$(1),$(1),youku-yk1,YOUKU-YK1)
> Image/Build/Profile/ZBT-WA05=$(call
> BuildFirmware/Default8M/$(1),$(1),zbt-wa05,ZBT-WA05)
> Image/Build/Profile/ZBT-WR8305RT=$(call
> BuildFirmware/Default8M/$(1),$(1),zbt-wr8305rt,ZBT-WR8305RT)
> Image/Build/Profile/ArcherC20i=$(call
> BuildFirmware/Tplink/$(1),$(1),ArcherC20i,ArcherC20i)
> @@ -939,6 +940,7 @@ define Image/Build/Profile/Default
> $(call Image/Build/Profile/WT3020,$(1))
> $(call Image/Build/Profile/MIWIFI-MINI,$(1))
> $(call Image/Build/Profile/ZTE-Q7,$(1))
> + $(call Image/Build/Profile/YOUKU-YK1,$(1))
> $(call Image/Build/Profile/ZBT-WA05,$(1))
> $(call Image/Build/Profile/ZBT-WR8305RT,$(1))
> $(call Image/Build/Profile/ArcherC20i,$(1))
>
_______________________________________________
openwrt-devel mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
