MZK-EX300NP is MT7620A based wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <[email protected]> --- target/linux/ramips/base-files/etc/board.d/01_leds | 1 + .../linux/ramips/base-files/etc/board.d/02_network | 1 + target/linux/ramips/base-files/etc/diag.sh | 1 + target/linux/ramips/base-files/lib/ramips.sh | 3 + .../ramips/base-files/lib/upgrade/platform.sh | 1 + target/linux/ramips/dts/MZK-EX300NP.dts | 132 +++++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 2 + target/linux/ramips/mt7620/profiles/planex.mk | 16 +++ 8 files changed, 157 insertions(+) create mode 100644 target/linux/ramips/dts/MZK-EX300NP.dts create mode 100644 target/linux/ramips/mt7620/profiles/planex.mk diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 5816e60..e8305d0 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -118,6 +118,7 @@ dir-615-h1) ucidef_set_led_default "status" "Status LED (amber)" "$board:amber:status" "0" set_wifi_led "rt2800pci-phy0::radio" ;; +mzk-ex300np|\ dir-620-d1) set_wifi_led "$board:green:wifi" ;; diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 4b65d36..db2e6d9 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -160,6 +160,7 @@ ramips_setup_interfaces() "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "9@eth0" ;; d105|\ + mzk-ex300np|\ hpm|\ na930|\ wli-tx4-ag300n) diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index daa7fb1..8692da9 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -151,6 +151,7 @@ get_status_led() { whr-600d) status_led="$board:orange:wifi" ;; + mzk-ex300np|\ rt-n10-plus|\ tew-691gr|\ tew-692gr|\ diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 5f1df7b..b1cb2eb 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -292,6 +292,9 @@ ramips_board_detect() { *"MZK-DP150N") name="mzk-dp150n" ;; + *"MZK-EX300NP") + name="mzk-ex300np" + ;; *"MZK-W300NH2"*) name="mzk-w300nh2" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index c329dce..d8e6f66 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -87,6 +87,7 @@ platform_check_image() { mr-102n|\ mt7628|\ mzk-dp150n|\ + mzk-ex300np|\ mzk-w300nh2|\ mzk-wdpr|\ nbg-419n|\ diff --git a/target/linux/ramips/dts/MZK-EX300NP.dts b/target/linux/ramips/dts/MZK-EX300NP.dts new file mode 100644 index 0000000..51e87ad --- /dev/null +++ b/target/linux/ramips/dts/MZK-EX300NP.dts @@ -0,0 +1,132 @@ +/dts-v1/; + +/include/ "mt7620a.dtsi" + +/ { + compatible = "ralink,mt7620a-soc"; + model = "Planex MZK-EX300NP"; + + palmbus@10000000 { + gpio1: gpio@638 { + status = "okay"; + }; + + gpio3: gpio@688 { + status = "okay"; + }; + + spi@b00 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0 0>; + linux,modalias = "m25p80", "w25q64"; + spi-max-frequency = <10000000>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0x730000>; + }; + + partition@780000 { + label = "Udata"; + reg = <0x780000 0x80000>; + }; + }; + }; + }; + + pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "i2c", "spi refclk", "rgmii1", "wled"; + ralink,function = "gpio"; + }; + }; + }; + + ethernet@10100000 { + pinctrl-names = "default"; + pinctrl-0 = <&ephy_pins>; + mtd-mac-address = <&factory 0x4>; + mediatek,portmap = "llllw"; + }; + + wmac@10180000 { + ralink,mtd-eeprom = <&factory 0>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + wifi { + label = "mzk-ex300np:green:wifi"; + gpios = <&gpio3 0 0>; + }; + + wps { + label = "mzk-ex300np:green:wps"; + gpios = <&gpio1 5 0>; + }; + + rep { + label = "mzk-ex300np:blue:rep"; + gpios = <&gpio1 4 1>; + }; + + wifi1 { + label = "mzk-ex300np:blue:wifi1"; + gpios = <&gpio1 1 1>; + }; + + wifi2 { + label = "mzk-ex300np:blue:wifi2"; + gpios = <&gpio1 2 1>; + }; + + wifi3 { + label = "mzk-ex300np:blue:wifi3"; + gpios = <&gpio1 0 1>; + }; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio0 1 1>; + linux,code = <0x198>; + }; + + wps { + label = "wps"; + gpios = <&gpio1 3 0>; + linux,code = <0x211>; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index 18cd20a..3c9d6ce 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -87,6 +87,7 @@ na930_mtd_size=20971520 Image/Build/Profile/NA930=$(call BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size)) Image/Build/Profile/DB-WRT01=$(call BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01) Image/Build/Profile/MZK-750DHP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP) +Image/Build/Profile/MZK-EX300NP=$(call BuildFirmware/Default8M/$(1),$(1),mzk-ex300np,MZK-EX300NP) Image/Build/Profile/HC5661=$(call BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661) Image/Build/Profile/HC5761=$(call BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761) Image/Build/Profile/HC5861=$(call BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861) @@ -131,6 +132,7 @@ define Image/Build/Profile/Default $(call Image/Build/Profile/WHR1166D,$(1)) $(call Image/Build/Profile/DB-WRT01,$(1)) $(call Image/Build/Profile/MZK-750DHP,$(1)) + $(call Image/Build/Profile/MZK-EX300NP,$(1)) $(call Image/Build/Profile/NA930,$(1)) $(call Image/Build/Profile/HC5661,$(1)) $(call Image/Build/Profile/HC5761,$(1)) diff --git a/target/linux/ramips/mt7620/profiles/planex.mk b/target/linux/ramips/mt7620/profiles/planex.mk new file mode 100644 index 0000000..79bfbdb --- /dev/null +++ b/target/linux/ramips/mt7620/profiles/planex.mk @@ -0,0 +1,16 @@ +# +# Copyright (C) 2015 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/MZK-EX300NP + NAME:=Planex MZK-EX300NP + PACKAGES:= +endef + +define Profile/MZK-EX300NP/Description + Package set optimized for the Planex MZK-EX300NP. +endef +$(eval $(call Profile,MZK-EX300NP)) -- 1.9.1 _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
