MZK-EX300NP is MT7620A based wifi repeater.
Built-in power supply.
64MiB RAM, 8MiB SPI Flash, non Wired Ethernet.
Signed-off-by: YuheiOKAWA <tochiro.srch...@gmail.com>
---
Changes in v3:
- rebase
- change an line in 01_leds and 02_network
- change gpio in dts
target/linux/ramips/base-files/etc/board.d/01_leds | 3 +-
.../linux/ramips/base-files/etc/board.d/02_network | 1 +
target/linux/ramips/base-files/etc/diag.sh | 1 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
.../ramips/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ramips/dts/MZK-EX300NP.dts | 132 +++++++++++++++++++++
target/linux/ramips/image/mt7620.mk | 2 +
target/linux/ramips/mt7620/profiles/planex.mk | 12 ++
8 files changed, 154 insertions(+), 1 deletion(-)
create mode 100644 target/linux/ramips/dts/MZK-EX300NP.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
b/target/linux/ramips/base-files/etc/board.d/01_leds
index e3b8500..3ab5f7f 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -118,7 +118,8 @@ dir-615-h1)
ucidef_set_led_default "status" "Status LED (amber)"
"$board:amber:status" "0"
set_wifi_led "rt2800pci-phy0::radio"
;;
-dir-620-d1)
+dir-620-d1|\
+mzk-ex300np)
set_wifi_led "$board:green:wifi"
;;
dir-810l|\
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index 3c958ae..c89b2a2 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -162,6 +162,7 @@ ramips_setup_interfaces()
;;
d105|\
hpm|\
+ mzk-ex300np|\
na930|\
wli-tx4-ag300n|\
wrh-300cr)
diff --git a/target/linux/ramips/base-files/etc/diag.sh
b/target/linux/ramips/base-files/etc/diag.sh
index bd0ff05..0eda084 100644
--- a/target/linux/ramips/base-files/etc/diag.sh
+++ b/target/linux/ramips/base-files/etc/diag.sh
@@ -154,6 +154,7 @@ get_status_led() {
whr-600d)
status_led="$board:orange:wifi"
;;
+ mzk-ex300np|\
rt-n10-plus|\
tew-691gr|\
tew-692gr|\
diff --git a/target/linux/ramips/base-files/lib/ramips.sh
b/target/linux/ramips/base-files/lib/ramips.sh
index 550ec55..e17aa94 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -292,6 +292,9 @@ ramips_board_detect() {
*"MZK-DP150N")
name="mzk-dp150n"
;;
+ *"MZK-EX300NP")
+ name="mzk-ex300np"
+ ;;
*"MZK-W300NH2"*)
name="mzk-w300nh2"
;;
diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
b/target/linux/ramips/base-files/lib/upgrade/platform.sh
index 73ba6e6..c0ee14e 100755
--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
@@ -88,6 +88,7 @@ platform_check_image() {
mt7628|\
mzk-750dhp|\
mzk-dp150n|\
+ mzk-ex300np|\
mzk-w300nh2|\
mzk-wdpr|\
nbg-419n|\
diff --git a/target/linux/ramips/dts/MZK-EX300NP.dts
b/target/linux/ramips/dts/MZK-EX300NP.dts
new file mode 100644
index 0000000..fd5c5cd
--- /dev/null
+++ b/target/linux/ramips/dts/MZK-EX300NP.dts
@@ -0,0 +1,132 @@
+/dts-v1/;
+
+/include/ "mt7620a.dtsi"
+
+/ {
+ compatible = "ralink,mt7620a-soc";
+ model = "Planex MZK-EX300NP";
+
+ palmbus@10000000 {
+ gpio1: gpio@638 {
+ status = "okay";
+ };
+
+ gpio3: gpio@688 {
+ status = "okay";
+ };
+
+ spi@b00 {
+ status = "okay";
+
+ m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0 0>;
+ linux,modalias = "m25p80", "w25q64";
+ spi-max-frequency = <10000000>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x30000>;
+ read-only;
+ };
+
+ partition@30000 {
+ label = "u-boot-env";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@40000 {
+ label = "factory";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "firmware";
+ reg = <0x50000 0x730000>;
+ };
+
+ partition@780000 {
+ label = "Udata";
+ reg = <0x780000 0x80000>;
+ };
+ };
+ };
+ };
+
+ pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "i2c", "spi refclk", "rgmii1",
"wled";
+ ralink,function = "gpio";
+ };
+ };
+ };
+
+ ethernet@10100000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ephy_pins>;
+ mtd-mac-address = <&factory 0x4>;
+ mediatek,portmap = "llllw";
+ };
+
+ wmac@10180000 {
+ ralink,mtd-eeprom = <&factory 0>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ wifi {
+ label = "mzk-ex300np:green:wifi";
+ gpios = <&gpio3 0 1>;
+ };
+
+ wps {
+ label = "mzk-ex300np:green:wps";
+ gpios = <&gpio1 5 1>;
+ };
+
+ rep {
+ label = "mzk-ex300np:blue:rep";
+ gpios = <&gpio1 4 1>;
+ };
+
+ wifi1 {
+ label = "mzk-ex300np:blue:wifi1";
+ gpios = <&gpio1 1 1>;
+ };
+
+ wifi2 {
+ label = "mzk-ex300np:blue:wifi2";
+ gpios = <&gpio1 2 1>;
+ };
+
+ wifi3 {
+ label = "mzk-ex300np:blue:wifi3";
+ gpios = <&gpio1 0 1>;
+ };
+ };
+
+ gpio-keys-polled {
+ compatible = "gpio-keys-polled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio0 1 1>;
+ linux,code = <0x198>;
+ };
+
+ wps {
+ label = "wps";
+ gpios = <&gpio1 3 0>;
+ linux,code = <0x211>;
+ };
+ };
+};
diff --git a/target/linux/ramips/image/mt7620.mk
b/target/linux/ramips/image/mt7620.mk
index c76e98e..2ff32c4 100644
--- a/target/linux/ramips/image/mt7620.mk
+++ b/target/linux/ramips/image/mt7620.mk
@@ -100,6 +100,7 @@ na930_mtd_size=20971520
Image/Build/Profile/NA930=$(call
BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
Image/Build/Profile/DB-WRT01=$(call
BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
Image/Build/Profile/MZK-750DHP=$(call
BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
+Image/Build/Profile/MZK-EX300NP=$(call
BuildFirmware/Default8M/$(1),$(1),mzk-ex300np,MZK-EX300NP)
Image/Build/Profile/HC5661=$(call
BuildFirmware/Default16M/$(1),$(1),hc5661,HC5661)
Image/Build/Profile/HC5761=$(call
BuildFirmware/Default16M/$(1),$(1),hc5761,HC5761)
Image/Build/Profile/HC5861=$(call
BuildFirmware/Default16M/$(1),$(1),hc5861,HC5861)
@@ -145,6 +146,7 @@ define Image/Build/Profile/Default
$(call Image/Build/Profile/WHR1166D,$(1))
$(call Image/Build/Profile/DB-WRT01,$(1))
$(call Image/Build/Profile/MZK-750DHP,$(1))
+ $(call Image/Build/Profile/MZK-EX300NP,$(1))
$(call Image/Build/Profile/NA930,$(1))
$(call Image/Build/Profile/HC5661,$(1))
$(call Image/Build/Profile/HC5761,$(1))
diff --git a/target/linux/ramips/mt7620/profiles/planex.mk
b/target/linux/ramips/mt7620/profiles/planex.mk
index f6f2cf1..e5ea6ed 100644
--- a/target/linux/ramips/mt7620/profiles/planex.mk
+++ b/target/linux/ramips/mt7620/profiles/planex.mk
@@ -14,3 +14,15 @@ define Profile/MZK-750DHP/Description
Package set optimized for the Planex MZK-750DHP.
endef
$(eval $(call Profile,MZK-750DHP))
+
+
+define Profile/MZK-EX300NP
+ NAME:=Planex MZK-EX300NP
+ PACKAGES:=
+endef
+
+define Profile/MZK-EX300NP/Description
+ Package set optimized for the Planex MZK-EX300NP.
+endef
+$(eval $(call Profile,MZK-EX300NP))
+
--
1.9.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
