This commit adds support for the ZBT WE1026-H, an outdoor AP with support for adding an internal LTE modem. The detailed specs are:
* CPU: MT7620A * 2x 10/100Mbps Ethernet (LAN port has passive PoE support). * 16/32 MB Flash. * 128/256 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slot (only USB2.0 bus). * 1x SIM slot (standard size). * 1x 2.4Ghz WIFI (rt2800). * 1x button. * 6x LEDS (4 GPIO-controlled). * 1x micro-SD reader. The following have been tested and working: - Ethernet switch - Wifi - Mini-PCIe slot + SIM slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or ito recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. Notes: * The LED labeled "USB" is used as the power LED. When binding this LED to a usbport, the LED is switched on all the time due to the presence of an internal hub. Thus, it does not really signal any USB-information. * I only have the 32MB version and have only added support for this device. However, the files are structured so that adding support for the 16MB version should be easy. * Only the LAN port is accessible from the outside of the casing and LEDs are not visible. Signed-off-by: Kristian Evensen <[email protected]> --- v2->v3: * Rebase on top of master. * Added label mac (thanks Adrian Schmutzler). * Fix consistent naming (thanks Adrian Schmutzler). v1->v2: * Rebased on top of master. * Read correct WAN address from flash (thanks Adrian Schmutzler). --- .../ramips/base-files/etc/board.d/01_leds | 5 +++ .../ramips/base-files/etc/board.d/02_network | 6 ++- .../dts/mt7620a_zbtlink_zbt-we1026-h-32m.dts | 14 +++++++ .../dts/mt7620a_zbtlink_zbt-we1026-h.dtsi | 40 +++++++++++++++++++ target/linux/ramips/image/mt7620.mk | 11 +++++ 5 files changed, 74 insertions(+), 2 deletions(-) create mode 100644 target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h-32m.dts create mode 100644 target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h.dtsi diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 662bf6b6cd..7b2310bc6f 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -461,6 +461,11 @@ zbtlink,zbt-we1026-5g-16m) ucidef_set_led_netdev "lan" "LAN" "we1026-5g:green:lan" "eth0" set_wifi_led "we1026-5g:green:wifi" ;; +zbtlink,zbt-we1026-h-32m) + set_wifi_led "we1026-h:green:wifi" + ucidef_set_led_switch "lan" "lan" "we1026-h:green:lan" "switch0" "0x8" + ucidef_set_led_switch "wan" "wan" "we1026-h:green:wan" "switch0" "0x10" + ;; zbtlink,zbt-we1226) set_wifi_led "$boardname:green:wlan" ucidef_set_led_switch "lan1" "LAN1" "$boardname:green:lan1" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 373651e64e..b2bfc91ebe 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -275,7 +275,8 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "5@eth0" ;; - buffalo,wcr-1166ds) + buffalo,wcr-1166ds|\ + zbtlink,zbt-we1026-h-32m) ucidef_add_switch "switch0" \ "3:lan" "4:wan" "6@eth0" ;; @@ -594,7 +595,8 @@ ramips_setup_macs() zyxel,keenetic-start) # This empty case has to be kept for devices without any MAC address adjustments ;; - cudy,wr1000) + cudy,wr1000|\ + zbtlink,zbt-we1026-h-32m) wan_mac=$(mtd_get_mac_binary factory 0x2e) label_mac=$(cat /sys/class/ieee80211/phy0/macaddress) ;; diff --git a/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h-32m.dts b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h-32m.dts new file mode 100644 index 0000000000..87430a9a6f --- /dev/null +++ b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h-32m.dts @@ -0,0 +1,14 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7620a_zbtlink_zbt-we1026-h.dtsi" + +/ { + compatible = "zbtlink,zbt-we1026-h-32m", "zbtlink,zbt-we1026-h", + "zbtlink,zbt-we1026","ralink,mt7620a-soc"; + model = "Zbtlink ZBT-WE1026-H (32M)"; +}; + +&firmware { + reg = <0x50000 0x1fb0000>; +}; diff --git a/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h.dtsi b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h.dtsi new file mode 100644 index 0000000000..0aa41dc5da --- /dev/null +++ b/target/linux/ramips/dts/mt7620a_zbtlink_zbt-we1026-h.dtsi @@ -0,0 +1,40 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7620a_zbtlink_zbt-we1026.dtsi" + +/ { + compatible = "zbtlink,zbt-we1026-h", "zbtlink,zbt-we1026", + "ralink,mt7620a-soc"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + led_power: usb { + label = "we1026-h:green:usb"; + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "we1026-h:green:lan"; + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "we1026-h:green:wan"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + }; + + wifi { + label = "we1026-h:green:wifi"; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index 95de1c0e46..aab5f86e83 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -984,6 +984,17 @@ define Device/zbtlink_zbt-we1026-5g-16m endef TARGET_DEVICES += zbtlink_zbt-we1026-5g-16m +define Device/zbtlink_zbt-we1026-h-32m + MTK_SOC := mt7620a + IMAGE_SIZE := 32448k + DEVICE_VENDOR := Zbtlink + DEVICE_MODEL := ZBT-WE1026-H + DEVICE_VARIANT := 32M + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci kmod-sdhci-mt7620 \ + kmod-ledtrig-netdev +endef +TARGET_DEVICES += zbtlink_zbt-we1026-h-32m + define Device/zbtlink_zbt-we2026 MTK_SOC := mt7620n IMAGE_SIZE := 7552k -- 2.20.1 _______________________________________________ openwrt-devel mailing list [email protected] https://lists.openwrt.org/mailman/listinfo/openwrt-devel
