On 27.05.20 15:33, Koen Vandeputte wrote:

On 07.05.20 13:46, Luochongjun wrote:
The gl-e750 is a portable travel router that gives you safe access to
the internet while traveling.

Specifications:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB DDR2
- Flash: 16 MB SPI NOR (W25Q128FVSG) + 128 MB SPI NAND (GD5F1GQ4UFYIG)
- Ethernet: 10/100: 1xLAN
- Wireless: QCA9531 2.4GHz (bgn) + QCA9887 5GHz (ac)
- USB: 1x USB 2.0 port
- Switch: 1x switch
- Button: 1x reset button
- OLED Screen: 128*64 px

Flash instruction:
Support for sysupgrade directive upgrades, as well as luci upgrades.

Hi,

I retested this patch just to be sure I didn't miss anything before.


Did you test this patch on actual hardware before sending this?

I've got 2x e750-Mudi devices which:

- I first flashed to the latest Gl.inet firmware (18.06 based) (works fine)

- Tried sysupgrade --> results in platform_check failure

- Tried forced sysupgrade --> does not boot afterwards

- Tried uboot recovery (both sysupgrade and factory images) --> does not boot


Using gl.inet official img, the uboot recovery mode works fine.

Thanks,

Koen


I just soldered UART to the board.

Ethernet is not coming up properly.

relevant prints:


[    0.551090] libphy: Fixed MDIO Bus: probed
[    0.872975] ag71xx 19000000.eth: Could not connect to PHY device. Deferring probe. [    0.881098] ag71xx 1a000000.eth: invalid MAC address, using random address
[    1.139873] random: fast init done
[    1.520295] libphy: ag71xx_mdio: probed
[    1.525811] libphy: ar8xxx-mdio: probed
[    1.538905] switch0: Atheros AR8229 rev. 1 switch registered on mdio.0
[    1.587451] ag71xx 1a000000.eth: connected to PHY at fixed-0:00 [uid=00000000, driver=Generic PHY]
[    1.597499] eth0: Atheros AG71xx at 0xba000000, irq 5, mode: gmii
[    1.605610] NET: Registered protocol family 10
[    1.614929] Segment Routing with IPv6
[    1.618900] NET: Registered protocol family 17
[    1.623601] 8021q: 802.1Q VLAN Support v1.8
[    1.631247] PCI host bridge /ahb/pcie-controller@180c0000 ranges:
[    1.637642]  MEM 0x0000000010000000..0x0000000013ffffff
[    1.643057]   IO 0x0000000000000000..0x0000000000000000
[    1.648655] PCI host bridge to bus 0000:00
[    1.652937] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[    1.660051] pci_bus 0000:00: root bus resource [io  0x0000]
[    1.665824] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    1.672845] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [    1.682374] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x101fffff 64bit] [    1.690010] pci 0000:00:00.0: BAR 6: assigned [mem 0x10200000-0x1020ffff pref] [    2.013961] ag71xx 19000000.eth: connected to PHY at mdio.0:1f:04 [uid=004dd042, driver=Generic PHY]
[    2.024473] eth1: Atheros AG71xx at 0xb9000000, irq 4, mode: mii

[   10.293731] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   11.325088] eth0: link up (1000Mbps/Full duplex)

[   11.329934] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready

[   17.716093] eth0: link down


this device also only has 1 ethernet port exposed on the board.

Regards,

Koen


_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel

Reply via email to