#17328: Installed 14.07 RC2 m xw in a New Nanostation loco M5 and hangs after
one
ping
--------------------------+-----------------------------------
Reporter: anonymous | Owner: developers
Type: defect | Status: new
Priority: normal | Milestone: Barrier Breaker 14.07
Component: base system | Version: Barrier Breaker 14.07
Resolution: | Keywords: m xw
--------------------------+-----------------------------------
Comment (by jb):
Replying to [comment:1 blogic]:
> can you get a serial log output ?
U-Boot 1.1.4-s776 (Nov 27 2013 - 15:58:45)
Board: Ubiquiti Networks AR9342 board (e845-51.1122.0030)
Reset: Normal
DRAM: 64 MB
Flash: 8 MB (0xc2, 0x20, 0x17)
Net: AR8032 Detected
eth0, eth1
Radio: 0777:e845
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-08-10 2:37:05 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1109393 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (openwrt@gb-10) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42092) ) #1 Sun Aug 10 02:32:17 UTC 2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9342 rev 2
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: board=UBNT-NM-XW console=ttyS0,115200
mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-
env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro rootfstype=squashfs,jffs2
noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61076k/65536k available (2375k kernel code, 4460k
reserved, 623k data, 264k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is Ubiquiti Nanostation M XW
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.320000] Switching to clocksource MIPS
[ 0.330000] NET: Registered protocol family 2
[ 0.330000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.330000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.340000] TCP: Hash tables configured (established 512 bind 512)
[ 0.340000] TCP: reno registered
[ 0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360000] NET: Registered protocol family 1
[ 0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.390000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.400000] msgmni has been set to 119
[ 0.400000] io scheduler noop registered
[ 0.400000] io scheduler deadline registered (default)
[ 0.410000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a
16550A
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.470000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.480000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.480000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.490000] Creating 5 MTD partitions on "spi0.0":
[ 0.490000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.500000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.510000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.520000] 2 uimage-fw partitions found on MTD device firmware
[ 0.530000] 0x000000050000-0x00000015edd1 : "kernel"
[ 0.530000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] 0x00000015edd1-0x0000007b0000 : "rootfs"
[ 0.550000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580000] 0x000000330000-0x0000007b0000 : "rootfs_data"
[ 0.590000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.590000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.600000] libphy: ag71xx_mdio: probed
[ 1.160000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01
[uid=004dd023, driver=Generic PHY]
[ 1.170000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.180000] TCP: cubic registered
[ 1.180000] NET: Registered protocol family 17
[ 1.190000] Bridge firewalling registered
[ 1.190000] 8021q: 802.1Q VLAN Support v1.8
[ 1.200000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 1.210000] Freeing unused kernel memory: 264K (8034e000 - 80390000)
procd: Console is alive
procd: - watchdog -
[ 3.510000] usbcore: registered new interface driver usbfs
[ 3.520000] usbcore: registered new interface driver hub
[ 3.520000] usbcore: registered new device driver usb
[ 3.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.540000] ehci-platform: EHCI generic platform driver
[ 3.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
[ 6.170000] eth0: link up (100Mbps/Full duplex)
jffs2 is ready
jffs2 is ready
[ 7.180000] jffs2: notice: (310) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of
xref (0 dead, 2 orphan) found.
switching to overlay
[ 7.220000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 8.650000] NET: Registered protocol family 10
[ 8.670000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[ 8.680000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.690000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 8.700000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 8.710000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.760000] xt_time: kernel timezone is -0000
[ 8.790000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.790000] cfg80211: World regulatory domain updated:
[ 8.800000] cfg80211: DFS Master region: unset
[ 8.800000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.810000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.820000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.830000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.840000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.840000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 8.850000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 8.860000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.870000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 8.950000] PPP generic driver version 2.4.2
[ 8.960000] NET: Registered protocol family 24
[ 9.040000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
[ 9.050000] cfg80211: Calling CRDA for country: US
[ 9.050000] cfg80211: Regulatory domain changed to country: US
[ 9.060000] cfg80211: DFS Master region: FCC
[ 9.060000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.070000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 9.080000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
1700 mBm), (N/A)
[ 9.090000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A,
2300 mBm), (0 s)
[ 9.100000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 9.110000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
procd: - init complete -
[ 16.490000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.510000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 16.530000] device eth0.1 entered promiscuous mode
[ 16.540000] device eth0 entered promiscuous mode
[ 16.550000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.580000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 17.240000] eth0: link up (100Mbps/Full duplex)
[ 17.240000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.270000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.270000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.280000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 17.280000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 17.290000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.270000] br-lan: port 1(eth0.1) entered forwarding state
U-Boot 1.1.4-s776 (Nov 27 2013 - 15:58:45)
Board: Ubiquiti Networks AR9342 board (e845-51.1122.0030)
Reset: Normal
DRAM: 64 MB
Flash: 8 MB (0xc2, 0x20, 0x17)
Net: AR8032 Detected
eth0, eth1
Radio: 0777:e845
Hit any key to stop autoboot: 0
## Booting image at 9f050000 ...
Image Name: MIPS OpenWrt Linux-3.10.49
Created: 2014-08-10 2:37:05 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1109393 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum at 0x9f050040 ...OK
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.49 (openwrt@gb-10) (gcc version 4.8.3
(OpenWrt/Linaro GCC 4.8-2014.04 r42092) ) #1 Sun Aug 10 02:32:17 UTC 2014
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] SoC: Atheros AR9342 rev 2
[ 0.000000] Clocks: CPU:535.000MHz, DDR:400.000MHz, AHB:200.000MHz,
Ref:40.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x03ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x03ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32
bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases,
linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 16256
[ 0.000000] Kernel command line: board=UBNT-NM-XW console=ttyS0,115200
mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-
env)ro,7552k(firmware),256k(cfg)ro,64k(EEPROM)ro rootfstype=squashfs,jffs2
noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768
bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61076k/65536k available (2375k kernel code, 4460k
reserved, 623k data, 264k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 266.64 BogoMIPS (lpj=1333248)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is Ubiquiti Nanostation M XW
[ 0.310000] bio: create slab <bio-0> at 0
[ 0.320000] Switching to clocksource MIPS
[ 0.330000] NET: Registered protocol family 2
[ 0.330000] TCP established hash table entries: 512 (order: 0, 4096
bytes)
[ 0.330000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.340000] TCP: Hash tables configured (established 512 bind 512)
[ 0.340000] TCP: reno registered
[ 0.350000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.350000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360000] NET: Registered protocol family 1
[ 0.380000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.390000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME)
(CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.400000] msgmni has been set to 119
[ 0.400000] io scheduler noop registered
[ 0.400000] io scheduler deadline registered (default)
[ 0.410000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.440000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a
16550A
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.450000] console [ttyS0] enabled, bootconsole disabled
[ 0.460000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.470000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.480000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.480000] 5 cmdlinepart partitions found on MTD device spi0.0
[ 0.490000] Creating 5 MTD partitions on "spi0.0":
[ 0.490000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.500000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.510000] 0x000000050000-0x0000007b0000 : "firmware"
[ 0.520000] 2 uimage-fw partitions found on MTD device firmware
[ 0.530000] 0x000000050000-0x00000015edd1 : "kernel"
[ 0.530000] mtd: partition "kernel" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.550000] 0x00000015edd1-0x0000007b0000 : "rootfs"
[ 0.550000] mtd: partition "rootfs" must either start or end on erase
block boundary or be smaller than an erase block -- forcing read-only
[ 0.570000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.570000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.580000] 0x000000330000-0x0000007b0000 : "rootfs_data"
[ 0.580000] 0x0000007b0000-0x0000007f0000 : "cfg"
[ 0.590000] 0x0000007f0000-0x000000800000 : "EEPROM"
[ 0.600000] libphy: ag71xx_mdio: probed
[ 1.160000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:01
[uid=004dd023, driver=Generic PHY]
[ 1.170000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.180000] TCP: cubic registered
[ 1.180000] NET: Registered protocol family 17
[ 1.190000] Bridge firewalling registered
[ 1.190000] 8021q: 802.1Q VLAN Support v1.8
[ 1.200000] VFS: Mounted root (squashfs filesystem) readonly on device
31:4.
[ 1.210000] Freeing unused kernel memory: 264K (8034e000 - 80390000)
procd: Console is alive
procd: - watchdog -
[ 3.510000] usbcore: registered new interface driver usbfs
[ 3.520000] usbcore: registered new interface driver hub
[ 3.520000] usbcore: registered new device driver usb
[ 3.530000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.540000] ehci-platform: EHCI generic platform driver
[ 3.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
procd: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug
level
[ 6.170000] eth0: link up (100Mbps/Full duplex)
jffs2 is ready
jffs2 is ready
[ 7.200000] jffs2: notice: (311) jffs2_build_xattr_subsystem: complete
building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 14 of
xref (0 dead, 2 orphan) found.
switching to overlay
[ 7.240000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 8.730000] NET: Registered protocol family 10
[ 8.740000] nf_conntrack version 0.5.0 (958 buckets, 3832 max)
[ 8.750000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 8.770000] Loading modules backported from Linux version
master-2014-05-22-0-gf2032ea
[ 8.780000] Backport generated by backports.git
backports-20140320-37-g5c33da0
[ 8.790000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.830000] xt_time: kernel timezone is -0000
[ 8.900000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.910000] cfg80211: World regulatory domain updated:
[ 8.910000] cfg80211: DFS Master region: unset
[ 8.920000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 8.930000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.930000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.940000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.950000] cfg80211: (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.960000] cfg80211: (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 8.970000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A,
2000 mBm), (0 s)
[ 8.980000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
2000 mBm), (N/A)
[ 8.980000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 0 mBm), (N/A)
[ 9.010000] PPP generic driver version 2.4.2
[ 9.030000] NET: Registered protocol family 24
[ 9.110000] cfg80211: Calling CRDA for country: US
[ 9.130000] cfg80211: Regulatory domain changed to country: US
[ 9.130000] cfg80211: DFS Master region: FCC
[ 9.140000] cfg80211: (start_freq - end_freq @ bandwidth),
(max_antenna_gain, max_eirp), (dfs_cac_time)
[ 9.150000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A,
3000 mBm), (N/A)
[ 9.150000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A,
1700 mBm), (N/A)
[ 9.160000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A,
2300 mBm), (0 s)
[ 9.170000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A,
3000 mBm), (N/A)
[ 9.180000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz),
(N/A, 4000 mBm), (N/A)
[ 9.190000] ieee80211 phy0: Atheros AR9340 Rev:0 mem=0xb8100000, irq=47
procd: - init complete -
[ 16.530000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.540000] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 16.540000] device eth0.1 entered promiscuous mode
[ 16.550000] device eth0 entered promiscuous mode
[ 16.550000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.590000] IPv6: ADDRCONF(NETDEV_UP): eth0.2: link is not ready
[ 17.420000] eth0: link up (100Mbps/Full duplex)
[ 17.500000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 17.550000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.550000] br-lan: port 1(eth0.1) entered forwarding state
[ 17.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready
[ 17.560000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.2: link becomes ready
[ 17.570000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 19.550000] br-lan: port 1(eth0.1) entered forwarding state
--
Ticket URL: <https://dev.openwrt.org/ticket/17328#comment:7>
OpenWrt <http://openwrt.org>
Opensource Wireless Router Technology
_______________________________________________
openwrt-tickets mailing list
[email protected]
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-tickets
