Open vSwitch is originally intended to switch at layer 2, only dealing with Ethernet frames. With the introduction of l3 tunnels support, it crossed into the realm of needing to care a bit about some routing details when making forwarding decisions. If an oversized packet would need to be fragmented during this forwarding decision, there is a chance for pmtu to get involved and generate a routing exception. This is gated by the skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is set up and transitioned properly as a packet moves from one port to another. In the case that a packet execute is invoked after a flow is newly installed this field is not properly initialized. This causes the pmtud mechanism to omit sending the required exception messages across the tunnel boundary and a second attempt needs to be made to make sure that the routing exception is properly setup. To fix this, we set the outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get to the openvswitch module via a port device or packet command. This issue is periodically encountered in complex setups, such as large openshift deployments, where multiple sets of tunnel traversal occurs. A way to recreate this is with the ovn-heater project that can setup a networking environment which mimics such large deployments. In that environment, without this patch, we can see: ./ovn_cluster.sh start podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200 podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache podman exec ovn-chassis-1 ip netns exec sw01p1 ping 21.0.0.3 -M do -s 1300 -c2 PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data. From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142) --- 21.0.0.3 ping statistics --- 2 packets transmitted, 0 received, +1 errors, 100% packet loss, time 1017ms Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not sent into the server. With this patch, setting the pkt_type, we see the following: podman exec ovn-chassis-1 ip netns exec sw01p1 ping 21.0.0.3 -M do -s 1300 -c2 PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data. From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222) ping: local error: message too long, mtu=1222 --- 21.0.0.3 ping statistics --- 2 packets transmitted, 0 received, +2 errors, 100% packet loss, time 1061ms In this case, the first ping request receives the FRAG_NEEDED message and a local routing exception is created. Reported-at: https://issues.redhat.com/browse/FDP-164 Fixes: 58264848a5a7 ("openvswitch: Add vxlan tunneling support.") Signed-off-by: Aaron Conole <[email protected]> --- NOTE: An alternate approach would be to add a netlink attribute to preserve pkt_type across the kernel->user boundary, but that does require some userspace cooperation. net/openvswitch/actions.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/net/openvswitch/actions.c b/net/openvswitch/actions.c index 6fcd7e2ca81fe..952c6292100d0 100644 --- a/net/openvswitch/actions.c +++ b/net/openvswitch/actions.c @@ -936,6 +936,8 @@ static void do_output(struct datapath *dp, struct sk_buff *skb, int out_port, pskb_trim(skb, ovs_mac_header_len(key)); } + skb->pkt_type = PACKET_OUTGOING; + if (likely(!mru || (skb->len <= mru + vport->dev->hard_header_len))) { ovs_vport_send(vport, skb, ovs_key_mac_proto(key)); -- 2.41.0 _______________________________________________ dev mailing list [email protected] https://mail.openvswitch.org/mailman/listinfo/ovs-dev
