I've only used the futurlec board for HVAC, which is 24VAC or so, but the
relays are rated at 10A @ 250VAC.
-Ben
On Wed, Nov 5, 2008 at 5:13 PM, Boyan Biandov <[EMAIL PROTECTED]>wrote:
> yes, plus rotating beacons, windshield wiper 12V motors and 110 AC
> solenoid valves for arrogation
>
> ~B
>
> -----Original Message-----
> From: Donald J. Organ IV [mailto:[EMAIL PROTECTED]
> Sent: Wednesday, November 05, 2008 2:08 PM
> To: [email protected]
> Subject: Re: [Owfs-developers] 1 Wire Switch & Solid State Relay
>
> Are you using this to control lighting??
>
>
> ----- Original Message -----
> From: "Mr Robert Conway" <[EMAIL PROTECTED]>
> To: [email protected]
> Sent: Wednesday, November 5, 2008 4:58:04 PM GMT -05:00 US/Canada
> Eastern
> Subject: Re: [Owfs-developers] 1 Wire Switch & Solid State Relay
>
> I have a pic of the futurelec relay board with the mods. I cut one end
> of the board completly off and then mounted the 1wire devices and
> installed in a case from Jaycar. I only run 24VDC through the relays so
> there is little heat biuld up
>
> http://rjconway.homeip.net/ Then click on [BLOG]
>
>
> rob
>
>
> ---- Ben Griffith <[EMAIL PROTECTED]> wrote:
> > Donald,
> >
> > I used an opto-isolated relay board from www.futurlec.com (
> > http://www.futurlec.com/Opto_Relay_4.shtml) and attached four DS2405
> > chips to it. Here is a link to the manual for the board:
> > http://www.picbasic.it/ETTe/ET-OPTO%20RELAY4%20Manual.pdf
> > And here is some text I sent to someone else describing what I did:
> >
> > If you have the manual that comes with the relay board you'll find
> > that to be helpful. Also the data sheet for the DS2405 (from Maxim's
> > web site). I just soldered a terminal block (3 terminals) and the
> > four DS2405 chips to the empty area on the relay board. The terminal
> > block is for connecting GND, +5V, and 1-wire data to the board. If
> > you arrange the chips one directly above the other in every other row
> > you can just use solder bridges to connect all of the GND pins
> > together and then all of the 1Wire pins together. Refer to my crude
> > diagram below. The DS2405 chips are arranged with the flat side
> > towards the top of the diagram (so the pins are 3-2-1 from left to
> right).
> >
> > ....[] <-- +5V terminal
> > ..__[] <-- 1-wire data terminal
> > ..|_[] <-- GND terminal
> > ..||..
> > .ooo.. <-- DS2405
> > ..||..
> > .ooo.. <-- DS2405
> > ..||..
> > .ooo.. <-- DS2405
> > ..||..
> > .ooo.. <-- DS2405
> > ......
> >
> > I removed one of the connectors from the opposite end of the board
> > and, using the manual as a reference, soldered wires from the +5V and
> > GND terminals I added, and from pin3 of each DS2405, all to the
> > appropriate spots where the connector had been. The connector I
> > removed was a single row connector with 6 pins (I think). It was the
> > one that the included cable does not fit on. It doesn't matter which
> > connector you use, since they all carry the same signals. Just refer
> to the manual for the pinout.
> >
> >
> >
> >
> > On Wed, Nov 5, 2008 at 3:35 PM, Donald J. Organ IV
> > <[EMAIL PROTECTED]>wrote:
> >
> > > Can anyone point me to some materials on using the DS2405 with a
> > > solid state relay. Basically what I am trying to do is control some
> lights.
> > >
> > > --------------------------------------------------------------------
> > > ----- This SF.Net email is sponsored by the Moblin Your Move
> > > Developer's challenge Build the coolest Linux based applications
> > > with Moblin SDK & win great prizes Grand prize is a trip for two to
> > > an Open Source event anywhere in the world
> > > http://moblin-contest.org/redirect.php?banner_id=100&url=/
> > > _______________________________________________
> > > Owfs-developers mailing list
> > > [email protected]
> > > https://lists.sourceforge.net/lists/listinfo/owfs-developers
> > >
> > >
>
>
> ------------------------------------------------------------------------
> -
> This SF.Net email is sponsored by the Moblin Your Move Developer's
> challenge Build the coolest Linux based applications with Moblin SDK &
> win great prizes Grand prize is a trip for two to an Open Source event
> anywhere in the world
> http://moblin-contest.org/redirect.php?banner_id=100&url=/
> _______________________________________________
> Owfs-developers mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/owfs-developers
>
> ------------------------------------------------------------------------
> -
> This SF.Net email is sponsored by the Moblin Your Move Developer's
> challenge Build the coolest Linux based applications with Moblin SDK &
> win great prizes Grand prize is a trip for two to an Open Source event
> anywhere in the world
> http://moblin-contest.org/redirect.php?banner_id=100&url=/
> _______________________________________________
> Owfs-developers mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/owfs-developers
>
> -------------------------------------------------------------------------
> This SF.Net email is sponsored by the Moblin Your Move Developer's
> challenge
> Build the coolest Linux based applications with Moblin SDK & win great
> prizes
> Grand prize is a trip for two to an Open Source event anywhere in the world
> http://moblin-contest.org/redirect.php?banner_id=100&url=/
> _______________________________________________
> Owfs-developers mailing list
> [email protected]
> https://lists.sourceforge.net/lists/listinfo/owfs-developers
>
-------------------------------------------------------------------------
This SF.Net email is sponsored by the Moblin Your Move Developer's challenge
Build the coolest Linux based applications with Moblin SDK & win great prizes
Grand prize is a trip for two to an Open Source event anywhere in the world
http://moblin-contest.org/redirect.php?banner_id=100&url=/
_______________________________________________
Owfs-developers mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/owfs-developers
