Sounds great. Take a look at http://www.extjs.com thats what we'll be using for our interfaces.
I am working on the installer right now that detects the devices and then allows you to label them. ----- Original Message ----- From: "Boyan Biandov" <[EMAIL PROTECTED]> To: [email protected] Sent: Wednesday, November 5, 2008 5:13:58 PM GMT -05:00 US/Canada Eastern Subject: Re: [Owfs-developers] 1 Wire Switch & Solid State Relay yes, plus rotating beacons, windshield wiper 12V motors and 110 AC solenoid valves for arrogation ~B -----Original Message----- From: Donald J. Organ IV [mailto:[EMAIL PROTECTED] Sent: Wednesday, November 05, 2008 2:08 PM To: [email protected] Subject: Re: [Owfs-developers] 1 Wire Switch & Solid State Relay Are you using this to control lighting?? ----- Original Message ----- From: "Mr Robert Conway" <[EMAIL PROTECTED]> To: [email protected] Sent: Wednesday, November 5, 2008 4:58:04 PM GMT -05:00 US/Canada Eastern Subject: Re: [Owfs-developers] 1 Wire Switch & Solid State Relay I have a pic of the futurelec relay board with the mods. I cut one end of the board completly off and then mounted the 1wire devices and installed in a case from Jaycar. I only run 24VDC through the relays so there is little heat biuld up http://rjconway.homeip.net/ Then click on [BLOG] rob ---- Ben Griffith <[EMAIL PROTECTED]> wrote: > Donald, > > I used an opto-isolated relay board from www.futurlec.com ( > http://www.futurlec.com/Opto_Relay_4.shtml) and attached four DS2405 > chips to it. Here is a link to the manual for the board: > http://www.picbasic.it/ETTe/ET-OPTO%20RELAY4%20Manual.pdf > And here is some text I sent to someone else describing what I did: > > If you have the manual that comes with the relay board you'll find > that to be helpful. Also the data sheet for the DS2405 (from Maxim's > web site). I just soldered a terminal block (3 terminals) and the > four DS2405 chips to the empty area on the relay board. The terminal > block is for connecting GND, +5V, and 1-wire data to the board. If > you arrange the chips one directly above the other in every other row > you can just use solder bridges to connect all of the GND pins > together and then all of the 1Wire pins together. Refer to my crude > diagram below. The DS2405 chips are arranged with the flat side > towards the top of the diagram (so the pins are 3-2-1 from left to right). > > ....[] <-- +5V terminal > ..__[] <-- 1-wire data terminal > ..|_[] <-- GND terminal > ..||.. > .ooo.. <-- DS2405 > ..||.. > .ooo.. <-- DS2405 > ..||.. > .ooo.. <-- DS2405 > ..||.. > .ooo.. <-- DS2405 > ...... > > I removed one of the connectors from the opposite end of the board > and, using the manual as a reference, soldered wires from the +5V and > GND terminals I added, and from pin3 of each DS2405, all to the > appropriate spots where the connector had been. The connector I > removed was a single row connector with 6 pins (I think). It was the > one that the included cable does not fit on. It doesn't matter which > connector you use, since they all carry the same signals. Just refer to the manual for the pinout. > > > > > On Wed, Nov 5, 2008 at 3:35 PM, Donald J. Organ IV > <[EMAIL PROTECTED]>wrote: > > > Can anyone point me to some materials on using the DS2405 with a > > solid state relay. Basically what I am trying to do is control some lights. > > > > -------------------------------------------------------------------- > > ----- This SF.Net email is sponsored by the Moblin Your Move > > Developer's challenge Build the coolest Linux based applications > > with Moblin SDK & win great prizes Grand prize is a trip for two to > > an Open Source event anywhere in the world > > http://moblin-contest.org/redirect.php?banner_id=100&url=/ > > _______________________________________________ > > Owfs-developers mailing list > > [email protected] > > https://lists.sourceforge.net/lists/listinfo/owfs-developers > > > > ------------------------------------------------------------------------ - This SF.Net email is sponsored by the Moblin Your Move Developer's challenge Build the coolest Linux based applications with Moblin SDK & win great prizes Grand prize is a trip for two to an Open Source event anywhere in the world http://moblin-contest.org/redirect.php?banner_id=100&url=/ _______________________________________________ Owfs-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/owfs-developers ------------------------------------------------------------------------ - This SF.Net email is sponsored by the Moblin Your Move Developer's challenge Build the coolest Linux based applications with Moblin SDK & win great prizes Grand prize is a trip for two to an Open Source event anywhere in the world http://moblin-contest.org/redirect.php?banner_id=100&url=/ _______________________________________________ Owfs-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/owfs-developers ------------------------------------------------------------------------- This SF.Net email is sponsored by the Moblin Your Move Developer's challenge Build the coolest Linux based applications with Moblin SDK & win great prizes Grand prize is a trip for two to an Open Source event anywhere in the world http://moblin-contest.org/redirect.php?banner_id=100&url=/ _______________________________________________ Owfs-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/owfs-developers ------------------------------------------------------------------------- This SF.Net email is sponsored by the Moblin Your Move Developer's challenge Build the coolest Linux based applications with Moblin SDK & win great prizes Grand prize is a trip for two to an Open Source event anywhere in the world http://moblin-contest.org/redirect.php?banner_id=100&url=/ _______________________________________________ Owfs-developers mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/owfs-developers
