Hi Ludovic, Thank you soo much for the last mail.
I have made some progress and the device can now connect and receive IP information. The directive on FlexConnect ACL I think did the trick. Also, it is seen as an online node. The challenge now is the captive portal does not pop up as the device remains in unregistered mode and is assigned a vlan 0 as against the guest vlan 300 [image: image.png] [image: image.png] How do I ensure that the captive portal comes up after connection? On Thu, 12 Nov 2020 at 14:50, Ludovic Zammit <lzam...@inverse.ca> wrote: > Hello Victor, > > Here’s few steps that you can validate before moving forward. > > SSID config: > > - AAA override checked, RADIUS NAC (or ISE) enabled > - Interface set to the correct guest vlan > - Since you are using flex connect, make sure your vlan / ACL are created > on the flex connect config > > PacketFence: > > - receive the radius request on each connection > - reply the portal URL + the ACL name for the captive portal > - enable the external portal on the switch > - getting the portal deamon listening to the management interface > > Do you have an IP address when you connect? > > You can do advanced debuting with the SSH Cisco CLI like: > > debug client mac aa:bb:cc:dd:ee:ff > > Look at the logs, they will tell you why you client can’t connect > successfully. > > Thanks, > > > Ludovic zammitlzam...@inverse.ca :: +1.514.447.4918 (x145) :: www.inverse.ca > Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu) and PacketFence > (http://packetfence.org) > > > > > > On Nov 12, 2020, at 3:02 AM, Ezeh Victor <vickeyzed...@gmail.com> wrote: > > Hi, > > Thanks for all your responses but I have gone through the provided links > prior to making this request. > > A little bit of additional detail; > > - My SSID is Open and is a flex connect SSID to enable users to pick > IP addresses from local DHCP servers > - I have my access-lists in place > - I have configured the controller on packet fence following the > documentation > - I have enabled the captive portal on the management interface > - I have enabled self preregistration > > My challenges however are; > > - I cannot connect to the SSID. I keep getting an authentication error. > - The captive portal does not show up > - I cannot see the controller node online as it is recorded as offline > on packetfence > > > I would appreciate a clear step on what to do based off of successful > implementations already done. > > The documentation has helped but I have not been successful. > > On Wed, 11 Nov 2020 at 20:14, Ludovic Zammit <lzam...@inverse.ca> wrote: > >> Hello, >> >> >> https://packetfence.org/doc/PacketFence_Network_Devices_Configuration_Guide.html#_cisco_2 >> >> Thanks, >> >> >> Ludovic zammitlzam...@inverse.ca :: +1.514.447.4918 (x145) :: >> www.inverse.ca >> Inverse inc. :: Leaders behind SOGo (http://www.sogo.nu) and PacketFence >> (http://packetfence.org) >> >> >> >> >> >> On Nov 10, 2020, at 8:24 AM, Ezeh Victor via PacketFence-users < >> packetfence-users@lists.sourceforge.net> wrote: >> >> Hi, >> >> Please I need assistance with figuring how I can integrate PacketFence >> with Cisco WLC. >> >> Any assistance will be appreciated. >> >> Regards. >> _______________________________________________ >> PacketFence-users mailing list >> PacketFence-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/packetfence-users >> >> >> >
_______________________________________________ PacketFence-users mailing list PacketFence-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/packetfence-users
