> From: [EMAIL PROTECTED]
> Message-ID: <[EMAIL PROTECTED]>
> Date: Sat, 13 Aug 2005 19:39:41 EDT
> Subject: Re: [PCI] Number of starts for my 7600 today...
> 
> In a message David Elmo <[EMAIL PROTECTED]> writes:
> 
> << In-Reply-To: <[EMAIL PROTECTED]>
> 
>> Subject: [PCI] Number of starts for my 7600 today...
>> From: David Elmo <[EMAIL PROTECTED]>
> 
>> Took 12 starts and restarts to get my 7600 fully booted today. It is so
>> fascinating ... and it rocks and is a rock for the rest of the day...
>> Yesterday, a miracle and only 3 starts... Average is 4 for last month.
>> 
>> David Elmo
> 
> Today, 15 starts. But Gauge Pro in a spare moment when I have a break, has
> come up with a memory error, which might explain all this nonsense that has
> been 
> going on for so long. "Memory Error at address $01FF4AB4 but read $05FF4AB4"
> I don't suppose anyone can say how i can usefully use this notice to pinpoint
> the chip concerned? If the following gets all unwrapped, I am sorry.
> 
> Memory overview
> Disk cache:    8160K
> Virtual memory:    is off
> Built-in memory:    832 MB
> 
> Location        Size    Memory type
> B4                    128 MB            DIMM
> A4                    64 MB            DIMM
> B3                    64 MB            DIMM
> A3                    64 MB            DIMM
> B2                    128 MB            DIM
> A2                    128 MB            DIMM
> B1                    128 MB            DIMM
> A1                    128 MB            DIMM
> External L2 cache:    Not installed>>
> 
> ----------------------------------------
> My reply:
> 
> There has been an incredibly good discussion on the G-list last week
> concerning the testing of DIMMs with Gauge Pro.
> 
> See these links to G-List archives -- be warned these are very long posts.
> 
> <http://www.mail-archive.com/g-list%40mail.maclaunch.com/msg38676.html>
> <http://www.mail-archive.com/g-list%40mail.maclaunch.com/msg38739.html>
> 
>> From these post it is believed the RAM used at startup is either the first
> slot, the last slot or possibly both. This theory predates the release of G3's
> and should apply to PCI Macs. The G's have only one bank of RAM and most of
> our 
> beloved PCI Mac have two.
> 
> So . . . assuming this premise if correct; I would remove the DIMMs in A1,
> B1, A4, B4 and run Gauge Pro again. If 7600 starts up OK and Gauge Pro comes
> up 
> negative you have isolated the bad DIMM to 4 chips. From there you can use the
> "sandwich" method as described in the links above to find the defective chip.
> 
> This all assumes (2nd assumption) that your startup problem is a result of
> defective RAM.
> 
> HTH --glen

Thanks, Glen. I am pretty sure that was my problem which I am now
sorting. I am a no good lazy SOB, my 7600 was in a very awkward
position on a shelf under the desktop, no room behind to walk. I
preferred to whinge to you lot and get by. But yesterday was Sunday and
I yanked it out and transferred the essentials to a 7300 spare case and
tested Ram and stuff and by reseating stuff and leaving out a sus stick
it now boots first go! I did it in a few hours, hating every moment.

The article you mention is good (it does not seem too long to me, I
like this stuff). But it is because I know this stuff more or less that
I have avoided applying it! It is such a drag to do this - it is like
being forced to watch paint dry! There are *some* unknowns to me like
which is the first slot (A1 I suppose) and which the last (B4?)... but
it does not matter much...

I have a test rig in a back room where I can do this time consuming
testing stuff and will do this to gain a respectable set of chips over
time... 

These ram software testers cannot so easily pick intermittent faults. A
stuck bit can be stuck a bit! What computers need is sophisticated
diagnostic testing going automatically in downtime (when user is not
working on anything, when no activity for a while).

David Elmo


-- 
PCI-PowerMacs is sponsored by <http://lowendmac.com/> and...

 Small Dog Electronics    http://www.smalldog.com  | Refurbished Drives |
 -- Sonnet & PowerLogix Upgrades - start at $169   |  & CDRWs on Sale!  |

      Support Low End Mac <http://lowendmac.com/lists/support.html>

PCI-PowerMacs list info: <http://lowendmac.com/lists/pci-powermacs.shtml>
  --> AOL users, remove "mailto:";
Send list messages to:   <mailto:[email protected]>
To unsubscribe, email:   <mailto:[EMAIL PROTECTED]>
For digest mode, email:  <mailto:[EMAIL PROTECTED]>
Subscription questions:  <mailto:[EMAIL PROTECTED]>
Archive:<http://www.mail-archive.com/pci-powermacs%40mail.maclaunch.com/>

iPod Accessories for Less
at 1-800-iPOD.COM
Fast Delivery, Low Price, Good Deal
www.1800ipod.com

Reply via email to