On Mon Oct 16, 2023 at 11:41 PM CEST, Nia Espera wrote:
> Hi,
>
> On 10/16/23 15:50, Luca Weiss wrote:
> > Hi Nia,
> >
> > On Mon Oct 16, 2023 at 2:47 PM CEST, Nia Espera wrote:
> >> Device tree files for OnePlus 9 and 9 Pro. Details of supported features
> >> mentioned in the cover letter for this patch series, but for
> >> accessibility also repeated here:
> >>
> >> - USB OTG
> >> - UFS
> >> - Framebuffer display
> >> - Touchscreen (for lemonade)
> >> - Power & volume down keys
> >> - Battery reading
> >> - Modem, IPA, and remoteproc bringup
> >>
> >> Steps to get booting:
> >>
> >> - Wipe dtbo partition
> >> - Flash vbmeta with disabled verity bit
> >> - Flash kernel and initfs to boot partition with CLI args pd_ignore_unused
> >> and clk_ignore_unused
> >> - Flash rootfs to some other partition (probably super or userdata)
> >>
> >> Signed-off-by: Nia Espera <nesp...@igalia.com>
> >> ---
> >> arch/arm64/boot/dts/qcom/Makefile | 2 +
> >> .../arm64/boot/dts/qcom/sm8350-oneplus-common.dtsi | 1247
> >> ++++++++++++++++++++
> >> .../boot/dts/qcom/sm8350-oneplus-lemonade.dts | 82 ++
> >> .../boot/dts/qcom/sm8350-oneplus-lemonadep.dts | 37 +
> >> 4 files changed, 1368 insertions(+)
> >>
> >> diff --git a/arch/arm64/boot/dts/qcom/Makefile
> >> b/arch/arm64/boot/dts/qcom/Makefile
> >> index 2cca20563a1d..369ad4721b29 100644
> >> --- a/arch/arm64/boot/dts/qcom/Makefile
> >> +++ b/arch/arm64/boot/dts/qcom/Makefile
> >> @@ -211,6 +211,8 @@ dtb-$(CONFIG_ARCH_QCOM) +=
> >> sm8250-xiaomi-elish-csot.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8350-hdk.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8350-microsoft-surface-duo2.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8350-mtp.dtb
> >> +dtb-$(CONFIG_ARCH_QCOM) += sm8350-oneplus-lemonade.dtb
> >> +dtb-$(CONFIG_ARCH_QCOM) += sm8350-oneplus-lemonadep.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8350-sony-xperia-sagami-pdx214.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8350-sony-xperia-sagami-pdx215.dtb
> >> dtb-$(CONFIG_ARCH_QCOM) += sm8450-hdk.dtb
> >> diff --git a/arch/arm64/boot/dts/qcom/sm8350-oneplus-common.dtsi
> >> b/arch/arm64/boot/dts/qcom/sm8350-oneplus-common.dtsi
> >> new file mode 100644
> >> index 000000000000..2f6768f35259
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/qcom/sm8350-oneplus-common.dtsi
> >> @@ -0,0 +1,1247 @@
> >> +// SPDX-License-Identifier: BSD-3-Clause
> >> +/*
> >> + * Copyright (c) 2023 Caleb Connolly <caleb.conno...@linaro.org>
> >> + *
> >> + * Copyright (c) 2023 Igalia S.L.
> >> + * Authors:
> >> + * Nia Espera <nesp...@igalia.com>
> >> + */
> >> +
> >> +#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
> >> +#include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
> >> +#define SMB139x_1_SID 0x0b
> >> +#define SMB139x_2_SID 0x0c
> >> +#include <dt-bindings/iio/qcom,spmi-adc7-smb139x.h>
> >> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
> >> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> >> +#include "sm8350.dtsi"
> >> +#include "pm8350.dtsi"
> >> +#include "pm8350b.dtsi"
> >> +#include "pm8350c.dtsi"
> >> +#include "pmk8350.dtsi"
> >> +#include "pmr735a.dtsi"
> >> +#include "pmr735b.dtsi"
> >> +
> >> +/ {
> >> + /* As with the Sony devices, msm-id and board-id aren't needed here */
> >> + chassis-type = "handset";
> >> + interrupt-parent = <&intc>;
> >> +
> >> + chosen {
> >> + #address-cells = <2>;
> >> + #size-cells = <2>;
> >> + ranges;
> >> +
> >> + framebuffer: framebuffer@e4d00000 {
> >> + compatible = "simple-framebuffer";
> >> + reg = <0 0xe4d00000 0 0x2400000>;
> >> + width = <1080>;
> >> + height = <2412>;
> >> + stride = <(1080 * 4)>;
> >> + format = "a8r8g8b8";
> >> + /*
> >> + * That's (going to be) a lot of clocks, but it's
> >> + * necessary due to unused clk cleanup & no panel
> >> + * driver yet.
> >> + */
> >> + clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
> >> + <&gcc GCC_DISP_SF_AXI_CLK>;
> >> + };
> >> + };
> >> +
> >> + gpio-keys {
> >> + compatible = "gpio-keys";
> >> +
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&vol_down_n>;
> >> +
> >> + key-vol-up {
> >> + label = "Volume Up";
> >> + linux,code = <KEY_VOLUMEUP>;
> >> + gpios = <&pmk8350_gpios 6 GPIO_ACTIVE_LOW>;
> >> + debounce-interval = <15>;
> >> + linux,can-disable;
> >> + wakeup-source;
> >> + };
> >> + };
> >> +
> >> + bat: battery {
> >> + compatible = "simple-battery";
> >> + device-chemistry = "lithium-ion";
> >> + voltage-min-design-microvolt = <3200000>;
> >> + energy-full-design-microwatt-hours = <15840000>;
> >> + charge-full-design-microamp-hours = <2225000>;
> >> + };
> >> +
> >> + vph_pwr: vph-pwr-regulator {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "vph_pwr";
> >> + regulator-min-microvolt = <3700000>;
> >> + regulator-max-microvolt = <3700000>;
> >> +
> >> + regulator-always-on;
> >> + regulator-boot-on;
> >> + };
> >> +
> >> + display_panel_avdd: display_regulator@1 {
> >> + compatible = "regulator-fixed";
> >> + regulator-name = "display_panel_avdd";
> >> + regulator-min-microvolt = <5500000>;
> >> + regulator-max-microvolt = <5500000>;
> >> + regulator-enable-ramp-delay = <233>;
> >> +
> >> + enable-active-high;
> >> + regulator-boot-on;
> >> + };
> >> +
> >> + /*
> >> + * Hack; OP9 bootloader specifically checks that the timer node has
> >> + * this label.
> >> + */
> >> + arch_timer: timer {};
> >> +};
> >> +
> >> +&reserved_memory {
> >> + /* EFI splash screen */
> >> + memory@e1000000 {
> >
> > Don't use memory@ names, this was decided a while ago to not be correct.
> > I think other devices here use e.g. splash@[..] or something.
>
> Noted, okay.
>
> >
> >> + reg = <0 0xe4d00000 0 0x02400000>;
> >> + no-map;
> >> + label = "cont_splash_region";
> >> + };
> >> +
> >> + ramoops: ramoops@E9700000 {
> >> + compatible = "ramoops";
> >> + reg = <0 0xe9700000 0 0x05b8000>;
> >> + record-size = <0x40000>;
> >> + console-size = <0x40000>;
> >> + ftrace-size = <0x200000>;
> >> + pmsg-size = <0x200000>;
> >> + devinfo-size = <0x08000>;
> >> + dumpinfo-size = <0x08000>;
> >> + rsv01info-size= <0x08000>;
> >> + rsv02info-size= <0x08000>;
> >> + rsv03info-size= <0x08000>;
> >> + rsv04info-size= <0x08000>;
> >> + rsv05info-size= <0x08000>;
> >> + ecc-size= <0x0>;
> >
> > Half of these flags don't exist. Did you run dtbs_check? Also
> > indentation normally doesn't get padded out in mainline, just do e.g.
> > record-size = <0x40000>; without the tab.
> >
>
> Mea culpa. Will fix, and run a check.
>
> >> + };
> >> +
> >> + /* bootloader log buffer */
> >> + memory@9fff7000 {
> >> + reg = <0x00 0x9fff7000 0x00 0x8000>;
> >> + };
> >> +
> >> + /* unknown; "param_mem" downstream */
> >> + memory@ea700000 {
> >> + reg = <0x00 0xea700000 0x00 0x800000>;
> >> + };
> >> +};
> >> +
> >> +&apps_rsc {
> >> + regulators-0 {
> >> + compatible = "qcom,pm8350-rpmh-regulators";
> >> + qcom,pmic-id = "b";
> >> +
> >> + vdd-s1-supply = <&vph_pwr>;
> >> + vdd-s2-supply = <&vph_pwr>;
> >> + vdd-s3-supply = <&vph_pwr>;
> >> + vdd-s4-supply = <&vph_pwr>;
> >> + vdd-s5-supply = <&vph_pwr>;
> >> + vdd-s6-supply = <&vph_pwr>;
> >> + vdd-s7-supply = <&vph_pwr>;
> >> + vdd-s8-supply = <&vph_pwr>;
> >> + vdd-s9-supply = <&vph_pwr>;
> >> + vdd-s10-supply = <&vph_pwr>;
> >> + vdd-s11-supply = <&vph_pwr>;
> >> + vdd-s12-supply = <&vph_pwr>;
> >> +
> >> + vdd-l1-l4-supply = <&pm8350_s11>;
> >> + vdd-l2-l7-supply = <&vreg_bob>;
> >> + vdd-l3-l5-supply = <&vreg_bob>;
> >> + vdd-l6-l9-l10-supply = <&pm8350_s11>;
> >> + vdd-l8-supply = <&pmr735a_s2>;
> >> +
> >> + /*
> >> + * ARC regulators:
> >> + * S5 - mx.lvl
> >> + * S6 - gfx.lvl
> >> + * S9 - mxc.lvl
> >> + */
> >> +
> >> + pm8350_s10: smps10 {
> >> + regulator-name = "pm8350_s10";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_s11: smps11 {
> >> + regulator-name = "pm8350_s11";
> >> + regulator-min-microvolt = <752000>;
> >> + regulator-max-microvolt = <1012000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_s12: smps12 {
> >> + regulator-name = "pm8350_s12";
> >> + regulator-min-microvolt = <1224000>;
> >> + regulator-max-microvolt = <1360000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_l1: ldo1 {
> >> + regulator-name = "pm8350_l1";
> >> + regulator-min-microvolt = <912000>;
> >> + regulator-max-microvolt = <920000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_l2: ldo2 {
> >> + regulator-name = "pm8350_l2";
> >> + regulator-min-microvolt = <3072000>;
> >> + regulator-max-microvolt = <3072000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_l3: ldo3 {
> >> + regulator-name = "pm8350_l3";
> >> + regulator-min-microvolt = <904000>;
> >> + regulator-max-microvolt = <904000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + /* L4 - lmx.lvl (ARC) */
> >> +
> >> + pm8350_l5: ldo5 {
> >> + regulator-name = "pm8350_l5";
> >> + regulator-min-microvolt = <880000>;
> >> + regulator-max-microvolt = <888000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + regulator-allow-set-load;
> >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> >> + RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_l6: ldo6 {
> >> + regulator-name = "pm8350_l6";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1208000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + regulator-allow-set-load;
> >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> >> + RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350_l7: ldo7 {
> >> + regulator-name = "pm8350_l7";
> >> + regulator-min-microvolt = <2400000>;
> >> + regulator-max-microvolt = <3008000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + regulator-allow-set-load;
> >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> >> + RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + /* L8 - lcx.lvl (ARC) */
> >> +
> >> + pm8350_l9: ldo9 {
> >> + regulator-name = "pm8350_l9";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + regulator-allow-set-load;
> >> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> >> + RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> + };
> >> +
> >> + regulators-1 {
> >> + compatible = "qcom,pm8350c-rpmh-regulators";
> >> + qcom,pmic-id = "c";
> >> +
> >> + vdd-s1-supply = <&vph_pwr>;
> >> + vdd-s2-supply = <&vph_pwr>;
> >> + vdd-s3-supply = <&vph_pwr>;
> >> + vdd-s4-supply = <&vph_pwr>;
> >> + vdd-s5-supply = <&vph_pwr>;
> >> + vdd-s6-supply = <&vph_pwr>;
> >> + vdd-s7-supply = <&vph_pwr>;
> >> + vdd-s8-supply = <&vph_pwr>;
> >> + vdd-s9-supply = <&vph_pwr>;
> >> + vdd-s10-supply = <&vph_pwr>;
> >> +
> >> + vdd-l1-l12-supply = <&pm8350c_s1>;
> >> + vdd-l2-l8-supply = <&pm8350c_s1>;
> >> + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
> >> + vdd-l6-l9-l11-supply = <&vreg_bob>;
> >> + vdd-l10-supply = <&pm8350_s12>;
> >> +
> >> + vdd-bob-supply = <&vph_pwr>;
> >> +
> >> + pm8350c_s1: smps1 {
> >> + regulator-name = "pm8350c_s1";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1952000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + /* S2 - ebi.lvl (ARC) */
> >> +
> >> + pm8350c_s3: smps3 {
> >> + regulator-name = "pm8350c_s3";
> >> + regulator-min-microvolt = <300000>;
> >> + regulator-max-microvolt = <704000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + /*
> >> + * ARC regulators:
> >> + * S4 - mss.lvl
> >> + * S6 - cx.lvl
> >> + * S8 - mmcx.lvl
> >> + */
> >> +
> >> + pm8350c_s10: smps10 {
> >> + regulator-name = "pm8350c_s10";
> >> + regulator-min-microvolt = <1048000>;
> >> + regulator-max-microvolt = <1128000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l1: ldo1 {
> >> + regulator-name = "pm8350c_l1";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l2: ldo2 {
> >> + regulator-name = "pm8350c_l2";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l3: ldo3 {
> >> + regulator-name = "pm8350c_l3";
> >> + regulator-min-microvolt = <3000000>;
> >> + regulator-max-microvolt = <3300000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l4: ldo4 {
> >> + regulator-name = "pm8350c_l4";
> >> + regulator-min-microvolt = <1704000>;
> >> + regulator-max-microvolt = <3000000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l5: ldo5 {
> >> + regulator-name = "pm8350c_l5";
> >> + regulator-min-microvolt = <1704000>;
> >> + regulator-max-microvolt = <3000000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l6: ldo6 {
> >> + regulator-name = "pm8350c_l6";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <2960000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l7: ldo7 {
> >> + regulator-name = "pm8350c_l7";
> >> + regulator-min-microvolt = <3008000>;
> >> + regulator-max-microvolt = <3008000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l8: ldo8 {
> >> + regulator-name = "pm8350c_l8";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l9: ldo9 {
> >> + regulator-name = "pm8350c_l9";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <3008000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l10: ldo10 {
> >> + regulator-name = "pm8350c_l10";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l11: ldo11 {
> >> + regulator-name = "pm8350c_l11";
> >> + regulator-min-microvolt = <2400000>;
> >> + regulator-max-microvolt = <3008000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l12: ldo12 {
> >> + regulator-name = "pm8350c_l12";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <2000000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + pm8350c_l13: ldo13 {
> >> + regulator-name = "pm8350c_l13";
> >> + regulator-min-microvolt = <3000000>;
> >> + regulator-max-microvolt = <3200000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> >> + };
> >> +
> >> + vreg_bob: bob {
> >> + regulator-name = "vreg_bob";
> >> + regulator-min-microvolt = <3400000>;
> >> + regulator-max-microvolt = <3960000>;
> >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> >> + };
> >> + };
> >> +
> >> + /* regulators-2 unused for now */
> >
> > Is there some PMIC that will be here? Since it's just numbered I also
> > don't see a problem renaming regulators-2 to regulators-3 if anything
> > was added later here.
> >
>
> Yep, pm8350b; no driver exists for it upstream and it's a single
> regulator that isn't particularly important (cannot find any references
> to it downstream, at least). I'll renumber the others.
>
> >> +
> >> + regulators-3 {
> >> + compatible = "qcom,pmr735a-rpmh-regulators";
> >> + qcom,pmic-id = "e";
> >> +
> >> + vdd-s1-supply = <&vph_pwr>;
> >> + vdd-s2-supply = <&vph_pwr>;
> >> + vdd-s3-supply = <&vph_pwr>;
> >> +
> >> + vdd-l1-l2-supply = <&pmr735a_s2>;
> >> + vdd-l3-supply = <&pmr735a_s1>;
> >> + vdd-l4-supply = <&pm8350c_s1>;
> >> + vdd-l5-l6-supply = <&pm8350c_s1>;
> >> + vdd-l7-bob-supply = <&vreg_bob>;
> >> +
> >> + pmr735a_s1: smps1 {
> >> + regulator-name = "pmr735a_s1";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1280000>;
> >> + };
> >> +
> >> + pmr735a_s2: smps2 {
> >> + regulator-name = "pmr735a_s2";
> >> + regulator-min-microvolt = <500000>;
> >> + regulator-max-microvolt = <976000>;
> >> + };
> >> +
> >> + pmr735a_s3: smps3 {
> >> + regulator-name = "pmr735a_s3";
> >> + regulator-min-microvolt = <2208000>;
> >> + regulator-max-microvolt = <2352000>;
> >> + };
> >> +
> >> + pmr735a_l1: ldo1 {
> >> + regulator-name = "pmr735a_l1";
> >> + regulator-min-microvolt = <912000>;
> >> + regulator-max-microvolt = <912000>;
> >> + };
> >> +
> >> + pmr735a_l2: ldo2 {
> >> + regulator-name = "pmr735a_l2";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + };
> >> +
> >> + pmr735a_l3: ldo3 {
> >> + regulator-name = "pmr735a_l3";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + };
> >> +
> >> + pmr735a_l4: ldo4 {
> >> + regulator-name = "pmr735a_l4";
> >> + regulator-min-microvolt = <1776000>;
> >> + regulator-max-microvolt = <1872000>;
> >> + };
> >> +
> >> + pmr735a_l5: ldo5 {
> >> + regulator-name = "pmr735a_l5";
> >> + regulator-min-microvolt = <800000>;
> >> + regulator-max-microvolt = <800000>;
> >> + };
> >> +
> >> + pmr735a_l6: ldo6 {
> >> + regulator-name = "pmr735a_l6";
> >> + regulator-min-microvolt = <480000>;
> >> + regulator-max-microvolt = <904000>;
> >> + };
> >> +
> >> + pmr735a_l7: ldo7 {
> >> + regulator-name = "pmr735a_l7";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> + };
> >> + };
> >> +};
> >> +
> >> +&adsp {
> >> + firmware-name = "qcom/OnePlus/lemonade/adsp.mbn";
> >> + status = "okay";
> >> +};
> >> +
> >> +&cdsp {
> >> + firmware-name = "qcom/OnePlus/lemonade/cdsp.mbn";
> >> + status = "okay";
> >> +};
> >> +
> >> +&slpi {
> >> + firmware-name = "qcom/OnePlus/lemonade/slpi.mbn";
> >> + status = "okay";
> >> +};
> >> +
> >> +&ipa {
> >> + qcom,gsi-loader = "self";
> >> + memory-region = <&pil_ipa_fw_mem>;
> >> + firmware-name = "qcom/OnePlus/lemonade/ipa_fws.mbn";
> >> + status = "okay";
> >> +};
> >> +
> >> +&mpss {
> >> + firmware-name = "qcom/OnePlus/lemonade/modem.mbn",
> >> + "qcom/OnePlus/lemonade/mcfg_hw.mbn";
> >
> > All these firmware-name attributes don't follow what's already in
> > mainline.
> >
> > Use e.g. qcom/sm8350/lemonade/*
>
> Noted, alright
>
> >
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&i2c4 {
> >> + clock-frequency = <400000>;
> >> + status = "okay";
> >> +
> >> + /* Touchscreens: Syna TCM oncell or Samsung s6sy761 */
> >> +};
> >> +
> >> +&i2c13 {
> >> + clock-frequency = <100000>;
> >> + status = "okay";
> >> +
> >> + fsa4480@42 {
> >> + compatible = "fcs,fsa4480";
> >> + reg = <0x42>;
> >> + mode-switch;
> >> + orientation-switch;
> >> + };
> >> +
> >> + /* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
> >
> > Check again in downstream if the @c and @d are actually enabled, at
> > least they're not on my boards and the PM8008 is only addressable on @8
> > and @9.
>
> Seems like they all are used on this device; (d) in particular seems to
> be needed for the camera.
PM8008 is a I2C-addressable regulator that is just used for camera. But
still if you have some time, double check if really both 8+9 and c+d are
used. For example you could use i2cdetect on the bus, I think the PM8008
shows up without manually flipping some enable GPIO. Or check downstream
dmesg to see what it says, or at runtime in /sys (e.g. in TWRP should be
enough).
>
> >> +};
> >> +
> >> +&i2c15 {
> >> + clock-frequency = <400000>;
> >> + status = "okay";
> >> +
> >> + /* sn-nci NFC controller @ 28 */
> >> +};
> >> +
> >> +&pm8350_gpios {
> >> + usb2_vbus_boost_default: usb2_vbus_boost_default {
> >> + pins = "gpio8";
> >> + function = "normal";
> >> + output-low;
> >> + power-source = <0x00>;
> >> + phandle = <0x5e1>;
> >> + };
> >> +
> >> + usb2_vbus_det_default: usb2_vbus_det_default {
> >> + pins = "gpio9";
> >> + function = "normal";
> >> + input-enable;
> >> + bias-disable;
> >> + power-source = <0x00>;
> >> + phandle = <0x5e0>;
> >> + };
> >
> > Node name should not have underscores, use dashes.
> >
> > Also here again I doubt you ran the dtbs_check, I think also the pmic
> > gpios need have have a -state suffix.
> >
> > => usb2_vbus_det_default: usb2-vbus-det-default-state {
> >
> >> +
> >> + gpio1_adc_default: gpio1-adc-default {
> >> + pins = "gpio1";
> >> + function = "normal";
> >> + bias-high-impedance;
> >> + bias-disable;
> >> + phandle = <0x566>;
> >> + };
> >> +
> >> + gpio3_adc_default: gpio3-adc-default {
> >> + pins = "gpio3";
> >> + function = "normal";
> >> + bias-high-impedance;
> >> + bias-disable;
> >> + phandle = <0x567>;
> >
> > Drop the random phandles you copied from the decompiled dtb?
>
> Oops...
>
> >
> >> + };
> >> +};
> >> +
> >> +&pm8350b_gpios {
> >> + vol_down_n: vol-down-n-state {
> >> + pins = "gpio6";
> >> + function = "normal";
> >> + power-source = <1>;
> >> + bias-pull-up;
> >> + input-enable;
> >> + };
> >> +};
> >> +
> >> +&pmk8350_rtc {
> >> + status = "okay";
> >> +};
> >> +
> >> +&pmk8350_vadc {
> >> + pinctrl-0 = <&gpio1_adc_default &gpio1_adc_default>;
> >> + pinctrl-names = "default";
> >> +
> >> + pmk8350_ref_gnd {
> >
> > Doesn't follow the format in the docs.
> >
> >> + reg = <0x00>;
> >> + label = "pmk8350_ref_gnd";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >
> > Don't use hex here.
> >
> >> + };
> >> +
> >> + pmk8350_vref_1p25 {
> >> + reg = <0x01>;
> >> + label = "pmk8350_vref_1p25";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmk8350_die_temp {
> >> + reg = <0x03>;
> >> + label = "pmk8350_die_temp";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmk8350_xo_therm {
> >> + reg = <0x44>;
> >> + label = "pmk8350_xo_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >
> > Make this also decimal.
> >
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350_ref_gnd {
> >> + reg = <0x100>;
> >> + label = "pm8350_ref_gnd";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350_vref_1p25 {
> >> + reg = <0x101>;
> >> + label = "pm8350_vref_1p25";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350_die_temp {
> >> + reg = <0x103>;
> >> + label = "pm8350_die_temp";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350_vph_pwr {
> >> + reg = <0x18e>;
> >> + label = "pm8350_vph_pwr";
> >> + qcom,pre-scaling = <0x01 0x03>;
> >> + };
> >> +
> >> + pm8350b_ref_gnd {
> >> + reg = <0x300>;
> >> + label = "pm8350b_ref_gnd";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350b_vref_1p25 {
> >> + reg = <0x301>;
> >> + label = "pm8350b_vref_1p25";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350b_die_temp {
> >> + reg = <0x303>;
> >> + label = "pm8350b_die_temp";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pm8350b_vph_pwr {
> >> + reg = <0x38e>;
> >> + label = "pm8350b_vph_pwr";
> >> + qcom,pre-scaling = <0x01 0x03>;
> >> + };
> >> +
> >> + pm8350b_vbat_sns {
> >> + reg = <0x38f>;
> >> + label = "pm8350b_vbat_sns";
> >> + qcom,pre-scaling = <0x01 0x03>;
> >> + };
> >> +
> >> + pm8350_msm_therm {
> >> + reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
> >> + label = "pm8350_msm_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350_cam_flash_therm {
> >> + reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
> >> + label = "pm8350_cam_flash_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350_hot_pocket_therm {
> >> + reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
> >> + label = "pm8350_hot_pocket_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350_wide_rfc_therm {
> >> + reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
> >> + label = "pm8350_wide_rfc_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350_rear_tof_therm {
> >> + reg = <PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
> >> + label = "pm8350_rear_tof_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350b_usb_conn_therm {
> >> + reg = <PM8350B_ADC7_AMUX_THM4_100K_PU>;
> >> + label = "pm8350b_usb_conn_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350b_wl_chg_therm {
> >> + reg = <PM8350B_ADC7_GPIO2_100K_PU>;
> >> + label = "pm8350b_wl_chg_therm";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <200>;
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pm8350b_chg_temp {
> >> + reg = <PM8350B_ADC7_CHG_TEMP>;
> >> + label = "pm8350b_chg_temp";
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + pmr735a_ref_gnd {
> >> + reg = <0x400>;
> >> + label = "pmr735a_ref_gnd";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmr735a_vref_1p25 {
> >> + reg = <0x401>;
> >> + label = "pmr735a_vref_1p25";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmr735a_die_temp {
> >> + reg = <0x403>;
> >> + label = "pmr735a_die_temp";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmr735b_ref_gnd {
> >> + reg = <0x500>;
> >> + label = "pmr735b_ref_gnd";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmr735b_vref_1p25 {
> >> + reg = <0x501>;
> >> + label = "pmr735b_vref_1p25";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + pmr735b_die_temp {
> >> + reg = <0x503>;
> >> + label = "pmr735b_die_temp";
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + smb139x_1_smb_temp {
> >> + reg = <SMB139x_1_ADC7_SMB_TEMP>;
> >> + label = "smb139x_1_smb_temp";
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + smb139x_2_smb_temp {
> >> + reg = <SMB139x_2_ADC7_SMB_TEMP>;
> >> + label = "smb139x_2_smb_temp";
> >> + qcom,pre-scaling = <1 1>;
> >> + };
> >> +
> >> + gpio1_v {
> >> + reg = <0x128>;
> >> + label = "gpio1_v";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0x2bc>;
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +
> >> + gpio3_v {
> >> + reg = <0x12b>;
> >> + label = "gpio3_v";
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0x2bc>;
> >> + qcom,pre-scaling = <0x01 0x01>;
> >> + };
> >> +};
> >> +
> >> +&pmk8350_adc_tm {
> >> + status = "okay";
> >> +
> >> + pm8350_msm_therm {
> >> + reg = <0x144>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >
> > Here also. Node name doesn't follow docs, missing io-channels (used here
> > instead of reg), etc.
> >
> >> + };
> >> +
> >> + pm8350_cam_flash_therm {
> >> + reg = <0x145>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pm8350_hot_pocket_therm {
> >> + reg = <0x146>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pm8350_wide_rfc_therm {
> >> + reg = <0x147>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pm8350_rear_tof_therm {
> >> + reg = <0x148>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pm8350b_usb_conn_therm {
> >> + reg = <0x347>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pm8350b_wl_chg_therm {
> >> + reg = <0x34b>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +
> >> + pmk8350_xo_therm {
> >> + reg = <0x44>;
> >> + qcom,ratiometric;
> >> + qcom,hw-settle-time = <0xc8>;
> >> + };
> >> +};
> >> +
> >> +&pon_pwrkey {
> >> + status = "okay";
> >> +};
> >> +
> >> +&pon_resin {
> >> + linux,code = <KEY_VOLUMEUP>;
> >> + status = "okay";
> >> +};
> >> +
> >> +&qupv3_id_0 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&qupv3_id_1 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&qupv3_id_2 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&gpi_dma0 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&gpi_dma1 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&gpi_dma2 {
> >> + status = "okay";
> >> +};
> >> +
> >> +&removed_mem {
> >> + reg = <0x0 0xd8800000 0x0 0x8e00000>;
> >> +};
> >> +
> >> +&tlmm {
> >> + gpio-reserved-ranges = <52 8>;
> >> +
> >> + pcie0_default_state: pcie0-default-state {
> >> + perst-pins {
> >> + pins = "gpio94";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + clkreq-pins {
> >> + pins = "gpio95";
> >> + function = "pcie0_clkreqn";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + wake-pins {
> >> + pins = "gpio96";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + sleep-pins {
> >> + pins = "gpio95";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> + };
> >> +
> >> + pcie1_default_state: pcie1-default-state {
> >> + perst-pins {
> >> + pins = "gpio97";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + clkreq-pins {
> >> + pins = "gpio98";
> >> + function = "pcie1_clkreqn";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + wake-pins {
> >> + pins = "gpio99";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + /* wil6210_refclk_en_pin lives here also */
> >> + };
> >> + };
> >> +
> >> + tp_rst_active: tp_rst_active {
> >
> > Wrong node name and more below.
> >
> >> + pins = "gpio22";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + /* tp_rst_suspend pin is different per device, don't specify here */
> >> +
> >> + tp_irq_active: tp_irq_active {
> >> + pins = "gpio23";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-disable;
> >> + input-enable;
> >> + };
> >> +
> >> + tp_irq_suspend: tp_irq_suspend {
> >> + pins = "gpio23";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + sde_dsi_active: sde-dsi-active {
> >> + pins = "gpio24";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-disable = <0>;
> >> + };
> >> +
> >> + sde_dsi_suspend: sde-dsi-suspend {
> >> + pins = "gpio24";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + sde_te_active: sde-te-active {
> >> + pins = "gpio82";
> >> + function = "mdp_vsync";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + sde_te_suspend: sde-te-suspend {
> >> + pins = "gpio82";
> >> + function = "mdp_vsync";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + aw_irq: aw_irq {
> >> + pins = "gpio14";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + aw_reset: aw_reset {
> >> + pins = "gpio75";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-disable;
> >> + };
> >
> > Skip unused pinctrl for now?
>
> Some of these I had meant to use but wasn't able to get everything quite
> working. Forgot to remove, sorry.
>
> >
> >> +
> >> + display_panel_avdd_default: display_panel_avdd_default {
> >> + pins = "gpio12";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-disable = <0>;
> >> + output-high;
> >> + };
> >> +
> >> + /* Modem-related pin common on both devices */
> >> + rf_cable_ant0_active: rf_cable_ant0_active {
> >> + pins = "gpio165";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + usb_int_default: usb_int_default {
> >> + pins = "gpio198";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + input-enable;
> >> + };
> >> +
> >> + qupv3_se18_default_cts: qupv3_se18_default_cts {
> >> + pins = "gpio68";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-disable;
> >> + };
> >> +
> >> + qupv3_se18_default_rtsrx: qupv3_se18_default_rtsrx {
> >> + pins = "gpio69", "gpio71";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + qupv3_se18_default_tx: qupv3_se18_default_tx {
> >> + pins = "gpio70";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + qupv3_se18_ctsrx: qupv3_se18_ctsrx {
> >> + pins = "gpio68", "gpio71";
> >> + function = "qup18";
> >> + drive-strength = <2>;
> >> + bias-disable;
> >> + };
> >> +
> >> + qupv3_se18_rts: qupv3_se18_rts {
> >> + pins = "gpio69";
> >> + function = "qup18";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + qupv3_se18_tx: qupv3_se18_tx {
> >> + pins = "gpio70";
> >> + function = "qup18";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + usb3phy_portselect_default: usb3phy_portselect_default {
> >> + pins = "gpio81";
> >> + function = "usb_phy";
> >> + drive-strength = <2>;
> >> + bias-disable;
> >> + };
> >> +
> >> + usb3phy_portselect_gpio: usb3phy_portselect_gpio {
> >> + pins = "gpio81";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-disable;
> >> + };
> >> +
> >> + ext1_otg_default: ext1_otg_default {
> >> + pins = "gpio8";
> >> + function = "gpio";
> >> + drive-strength = <16>;
> >> + bias-pull-down;
> >> + input-enable;
> >> + };
> >> +
> >> + cnss_wlan_en_active: cnss_wlan_en_active {
> >> + pins = "gpio64";
> >> + function = "gpio";
> >> + drive-strength = <16>;
> >> + output-high;
> >> + bias-pull-up;
> >> + };
> >> +
> >> + cnss_wlan_en_sleep: cnss_wlan_en_sleep {
> >> + pins = "gpio64";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + output-low;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + bt_en_sleep: bt_en_sleep {
> >> + pins = "gpio65";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + output-low;
> >> + bias-pull-down;
> >> + };
> >> +};
> >> +
> >> +&ufs_mem_hc {
> >> + reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;
> >> +
> >> + vcc-supply = <&pm8350_l7>;
> >> + vcc-voltage-level = <2504000 2950000>;
> >> + vcc-max-microamp = <800000>;
> >> + vccq-supply = <&pm8350_l9>;
> >> + vccq-max-microamp = <900000>;
> >> +
> >> + qcom,vddp-ref-clk-supply = <&pm8350_l9>;
> >> + qcom,vddp-ref-clk-max-microamp = <100>;
> >> +
> >> + qcom,vddp-ref-clk-supply = <&pm8350_s12>;
> >> + qcom,vccq-parent-max-microamp = <210000>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&ufs_mem_phy {
> >> + vdda-phy-supply = <&pm8350_l5>;
> >> + vdda-phy-always-on;
> >
> > Property doesn't exist
> >
> >> + vdda-max-microamp = <91600>;
> >> + vdda-pll-supply = <&pm8350_l6>;
> >> + vdda-pll-max-microamp = <19000>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&usb_1 {
> >> + /* Bug in interconnect driver breaks USB */
> >> + /delete-property/ interconnects;
> >> + /delete-property/ interconnect-names;
> >
> > Any chance on fixing this? Or add some extra explanation? Not sure how
> > liked such workarounds are in dts files.
>
> Enabling that makes USB perma-broken as the regulators get stuck at off;
> I can investigate more if that would be necessary.
>
> >> +
> >> + /*
> >> + * USB3 is not tested (though it is enabled downstream) so limit to
> >> + * high-speed for now.
> >> + */
> >> + qcom,select-utmi-as-pipe-clk;
> >
> > You never plugged the device into a USB 3.0 port? Should be trivial to
> > test I think?
>
> Will test for v2.
>
> >
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&usb_1_dwc3 {
> >> + /* Mode switching is untested */
> >> + dr_mode = "peripheral";
> >> + maximum-speed = "high-speed";
> >> + phys = <&usb_1_hsphy>;
> >> + phy-names = "usb2-phy";
> >> +};
> >> +
> >> +&usb_1_hsphy {
> >> + vdda-pll-supply = <&pm8350_l5>;
> >> + vdda18-supply = <&pm8350c_l1>;
> >> + vdda33-supply = <&pm8350_l2>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +/* Enabling this is necessary only for displayport */
> >
> > Do you have displayport support with this dts? If not why enable it?
>
> Fair enough, no. Panel driver is still WIP, will upstream this bit when
> that's working.
>
> >
> >> +&usb_1_qmpphy {
> >> + vdda-phy-supply = <&pm8350_l6>;
> >> + vdda-pll-supply = <&pm8350_l1>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&i2c2 {
> >> + clock-frequency = <100000>;
> >> + status = "okay";
> >> +
> >> + bq27541: fuel-gauge@55 {
> >> + compatible = "ti,bq27541";
> >> + reg = <0x55>;
> >> + monitored-battery = <&bat>;
> >> + };
> >> +};
> >> +/* Crypto drivers currently fail & cause an XPU violation */
> >
> > Missing newline between nodes.
> >
> >> +&cryptobam {
> >> + status = "disabled";
> >> +};
> >> +
> >> +&crypto {
> >> + status = "disabled";
> >> +};
> >
> > These disables are not useful since they're already disabled in
> > sm8350.dtsi because of that problem.
>
> This was here before that fix landed, but I missed it; will remove.
>
> >
> >> +
> >> +&pcie0 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&pcie0_default_state>;
> >> +
> >> + perst-gpios = <&tlmm 94 GPIO_ACTIVE_HIGH>;
> >> + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&pcie0_phy {
> >> + vdda-phy-supply = <&pm8350_l5>;
> >> + vdda-pll-supply = <&pm8350_l6>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&pcie1 {
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&pcie1_default_state>;
> >> +
> >> + perst-gpios = <&tlmm 97 GPIO_ACTIVE_HIGH>;
> >> + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
> >> +
> >> + status = "okay";
> >> +};
> >> +
> >> +&pcie1_phy {
> >> + vdda-phy-supply = <&pm8350_l5>;
> >> + vdda-pll-supply = <&pm8350_l6>;
> >> +
> >> + status = "okay";
> >> +};
> >
> > Everywhere in this file make sure the nodes are sorted alphabetically,
> > it's a wild west right now.
>
> Understandable, will do.
>
> >
> >> diff --git a/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonade.dts
> >> b/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonade.dts
> >> new file mode 100644
> >> index 000000000000..f2c27894f3c4
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonade.dts
> >> @@ -0,0 +1,82 @@
> >> +// SPDX-License-Identifier: BSD-3-Clause
> >> +/*
> >> + * Copyright (c) 2023 Igalia S.L.
> >> + * Authors:
> >> + * Nia Espera <nesp...@igalia.com>
> >> + */
> >> +
> >> +/dts-v1/;
> >> +
> >> +#include "sm8350-oneplus-common.dtsi"
> >> +
> >> +/ {
> >> + model = "OnePlus 9";
> >> + compatible = "oneplus,lemonade", "qcom,sm8350";
> >> +};
> >> +
> >> +&i2c4 {
> >> + touchscreen@48 {
> >> + compatible = "samsung,s6sy761";
> >> + reg = <0x48>;
> >> + interrupts-extended = <&tlmm 23 0x2008>;
> >
> > Replace the 0x2008 with the GPIO_* flags from
> > include/dt-bindings/gpio/gpio.h
>
> There doesn't seem to be a flag for 0x2000 and it's not documented
> downstream; is it okay to replace with (0x2000|GPIO_TRANSITORY)?
As Krzysztof already replied, my fault, should be the defines from irq.h
since this is obviously an interrupt, not a gpio property.
Regards
Luca
>
> >
> >> +
> >> + vdd-supply = <&pm8350c_l8>;
> >> + avdd-supply = <&pm8350c_l13>;
> >> +
> >> + pinctrl-names = "default", "sleep";
> >> + pinctrl-0 = <&tp_rst_active &tp_irq_active>;
> >> + pinctrl-1 = <&tp_rst_suspend &tp_irq_suspend>;
> >> + };
> >> +};
> >> +
> >> +&tlmm {
> >> + tp_rst_suspend: tp_rst_suspend {
> >> + pins = "gpio22";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + tp_enable_2v8: tp_enable_2v8 {
> >> + pins = "gpio74";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-pull-up;
> >> + output-high;
> >> + };
> >
> > Some pinctrl comments as in the .dtsi file
> >
> >> +
> >> + /* Modem antenna pins exclusive to lemonade */
> >> + rf_cable_ant1_active: rf_cable_ant1_active {
> >> + pins = "gpio27";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> + rf_cable_ant2_active: rf_cable_ant2_active {
> >> + pins = "gpio92";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> + rf_cable_ant3_active: rf_cable_ant3_active {
> >> + pins = "gpio44";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> + rf_cable_ant7_active: rf_cable_ant7_active {
> >> + pins = "gpio155";
> >> + function = "gpio";
> >> + drive-strength = <2>;
> >> + bias-pull-up;
> >> + };
> >> +};
> >> +
> >> +&mpss {
> >> + pinctrl-names = "default";
> >> + pinctrl-1 = <&rf_cable_ant0_active
> >> + &rf_cable_ant1_active
> >> + &rf_cable_ant2_active
> >> + &rf_cable_ant3_active
> >> + &rf_cable_ant7_active>;
> >> +};
> >> diff --git a/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonadep.dts
> >> b/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonadep.dts
> >> new file mode 100644
> >> index 000000000000..de8597d26091
> >> --- /dev/null
> >> +++ b/arch/arm64/boot/dts/qcom/sm8350-oneplus-lemonadep.dts
> >> @@ -0,0 +1,37 @@
> >> +// SPDX-License-Identifier: BSD-3-Clause
> >> +/*
> >> + * Copyright (c) 2023 Igalia S.L.
> >> + * Authors:
> >> + * Nia Espera <nesp...@igalia.com>
> >> + */
> >> +
> >> +/dts-v1/;
> >> +
> >> +#include "sm8350-oneplus-common.dtsi"
> >> +
> >> +/ {
> >> + model = "OnePlus 9 Pro";
> >> + compatible = "oneplus,lemonadep", "qcom,sm8350";
> >> +};
> >> +
> >> +&tlmm {
> >> + tp_rst_suspend: tp_rst_suspend {
> >> + pins = "gpio22";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-pull-down;
> >> + };
> >> +
> >> + tp_enable_2v8: tp_enable_2v8 {
> >> + pins = "gpio31";
> >> + function = "gpio";
> >> + drive-strength = <8>;
> >> + bias-pull-up;
> >> + output-high;
> >> + };
> >
> > And don't forget about fixing the nodes here. But why define them now if
> > you don't have any users of them?
>
> Oopsies- same as previous pins, op9p touchscreen isn't ready yet and I
> left these in.
>
> >
> >> +};
> >> +
> >> +&mpss {
> >> + pinctrl-names = "default";
> >> + pinctrl-1 = <&rf_cable_ant0_active>;
> >> +};
> >
> > I'm sure others will have more comments but fixing the comments I added
> > is a good step forward :)
>
> Thanks for your time! I'll fix up everything mentioned.
>
> >
> > Regards
> > Luca
