Pierwszy raz tego używam i nie bardzo wiem jak to czytać ;-(
(co to SMART wiem).
Są tu bad sectory ??
[root@Misiek ~]# smartctl -a /dev/sdd
smartctl 6.1 2013-03-16 r3800 [x86_64-linux-3.9.8-1] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar Green (AF, SATA 6Gb/s)
Device Model: WDC WD30EZRX-00MMMB0
Serial Number: WD-WCAWZ1392493
LU WWN Device Id: 5 0014ee 25b9c4145
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 11 13:31:08 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test
routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (51000) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 490) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail
Always - 17
3 Spin_Up_Time 0x0027 228 148 021 Pre-fail
Always - 5575
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 119
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age
Always - 180
9 Power_On_Hours 0x0032 080 080 000 Old_age
Always - 14641
10 Spin_Retry_Count 0x0032 100 100 000 Old_age
Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 116
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age
Always - 91
193 Load_Cycle_Count 0x0032 001 001 000 Old_age
Always - 783887
194 Temperature_Celsius 0x0022 126 117 000 Old_age
Always - 26
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age
Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
On 10.07.2013 22:50, Andrzej Zawadzki wrote:
On 10.07.2013 18:22, lord_Niedzwiedz wrote:
Dziwna sprawa. Jak korzystam z RAID'a md2 to wszystko śmiga na 3
dyskach
(czwarty specjalnie wypiety - spowalniało).
A co SMART mówi na temat /dev/sdd ?
A w jakiej paczce go znajdę i jak go użyć ?? ;/
smartmontools
smartctl -a /dev/sdd
już powinien coś pokazać.
Zawsze możesz mu zrobić test:
smartctl --test=long /dev/sdd
Powodzenia!
--
Pozdro
lord_Niedzwiedz
_______________________________________________
pld-users-pl mailing list
[email protected]
http://lists.pld-linux.org/mailman/listinfo/pld-users-pl
