lord_Niedzwiedz <[email protected]> napisał: > Pierwszy raz tego używam i nie bardzo wiem jak to czytać ;-( >(co to SMART wiem). >Są tu bad sectory ?? > >[root@Misiek ~]# smartctl -a /dev/sdd >smartctl 6.1 2013-03-16 r3800 [x86_64-linux-3.9.8-1] (local build) >Copyright (C) 2002-13, Bruce Allen, Christian Franke, >www.smartmontools.org > >=== START OF INFORMATION SECTION === >Model Family: Western Digital Caviar Green (AF, SATA 6Gb/s) >Device Model: WDC WD30EZRX-00MMMB0 >Serial Number: WD-WCAWZ1392493 >LU WWN Device Id: 5 0014ee 25b9c4145 >Firmware Version: 80.00A80 >User Capacity: 3,000,592,982,016 bytes [3,00 TB] >Sector Sizes: 512 bytes logical, 4096 bytes physical >Device is: In smartctl database [for details use: -P show] >ATA Version is: ATA8-ACS (minor revision not indicated) >SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) >Local Time is: Thu Jul 11 13:31:08 2013 CEST >SMART support is: Available - device has SMART capability. >SMART support is: Enabled > >=== START OF READ SMART DATA SECTION === >SMART overall-health self-assessment test result: PASSED > >General SMART Values: >Offline data collection status: (0x84) Offline data collection >activity > was suspended by an interrupting command from host. > Auto Offline Data Collection: Enabled. >Self-test execution status: ( 0) The previous self-test >routine completed > without error or no self-test has ever > been run. >Total time to complete Offline >data collection: (51000) seconds. >Offline data collection >capabilities: (0x7b) SMART execute Offline immediate. > Auto Offline data collection on/off support. > Suspend Offline collection upon new > command. > Offline surface scan supported. > Self-test supported. > Conveyance Self-test supported. > Selective Self-test supported. >SMART capabilities: (0x0003) Saves SMART data before >entering > power-saving mode. > Supports SMART auto save timer. >Error logging capability: (0x01) Error logging supported. > General Purpose Logging supported. >Short self-test routine >recommended polling time: ( 2) minutes. >Extended self-test routine >recommended polling time: ( 490) minutes. >Conveyance self-test routine >recommended polling time: ( 5) minutes. >SCT capabilities: (0x3035) SCT Status supported. > SCT Feature Control supported. > SCT Data Table supported. > >SMART Attributes Data Structure revision number: 16 >Vendor Specific SMART Attributes with Thresholds: >ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED >WHEN_FAILED RAW_VALUE > 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail >Always - 17 > 3 Spin_Up_Time 0x0027 228 148 021 Pre-fail >Always - 5575 > 4 Start_Stop_Count 0x0032 100 100 000 Old_age >Always - 119 > 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail >Always - 0 > 7 Seek_Error_Rate 0x002e 200 200 000 Old_age >Always - 180 > 9 Power_On_Hours 0x0032 080 080 000 Old_age >Always - 14641 > 10 Spin_Retry_Count 0x0032 100 100 000 Old_age >Always - 0 > 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age >Always - 0 > 12 Power_Cycle_Count 0x0032 100 100 000 Old_age >Always - 116 >192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age >Always - 91 >193 Load_Cycle_Count 0x0032 001 001 000 Old_age >Always - 783887 >194 Temperature_Celsius 0x0022 126 117 000 Old_age >Always - 26 >196 Reallocated_Event_Count 0x0032 200 200 000 Old_age >Always - 0 >197 Current_Pending_Sector 0x0032 200 200 000 Old_age >Always - 0 >198 Offline_Uncorrectable 0x0030 200 200 000 Old_age >Offline - 0 >199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age >Always - 0 >200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age >Offline - 0 > >SMART Error Log Version: 1 >No Errors Logged > >SMART Self-test log structure revision number 1 >No self-tests have been logged. [To run self-tests, use: smartctl -t] > > >SMART Selective self-test log data structure revision number 1 > SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS > 1 0 0 Not_testing > 2 0 0 Not_testing > 3 0 0 Not_testing > 4 0 0 Not_testing > 5 0 0 Not_testing >Selective self-test flags (0x0): > After scanning selected spans, do NOT read-scan remainder of disk. >If Selective self-test is pending on power-up, resume after 0 minute >delay. > > > >On 10.07.2013 22:50, Andrzej Zawadzki wrote: >> On 10.07.2013 18:22, lord_Niedzwiedz wrote: >>>>> Dziwna sprawa. Jak korzystam z RAID'a md2 to wszystko śmiga na 3 >>>>> dyskach >>>>> (czwarty specjalnie wypiety - spowalniało). >>>> A co SMART mówi na temat /dev/sdd ? >>> A w jakiej paczce go znajdę i jak go użyć ?? ;/ >>> >> smartmontools >> >> smartctl -a /dev/sdd >> już powinien coś pokazać. >> >> Zawsze możesz mu zrobić test: >> >> smartctl --test=long /dev/sdd >> >> Powodzenia! >>
Niby niczego złego nie widać. Zapuść jeszcze smartctl --test=long na tym dysku i po jakimś czasie znów sprawdź -a (chociaż pełny test zająłby kilka(naście) godzin, ale jak tak źle się zachowuje to pewnie wywróci się wcześniej). A tak na marginesie - jesteś pewien, że nie ma problemu z podłączeniem dysku (taśma/backend itp)? -- Pozdrawiam. Łukasz Maśko Wysłane za pomocą K-9 Mail. _______________________________________________ pld-users-pl mailing list [email protected] http://lists.pld-linux.org/mailman/listinfo/pld-users-pl
