Hi. Tried FreeBSD this time, but it crashes immediately (log attached). I found that strange, so I tested a little, and found out that the root-image to use afterwards crashed with the same error....? Am I doing something wrong? Images can be gotten from ftp://ftp.freebsd.org/pub/FreeBSD/releases/i386/4.2-RELEASE/floppies/ kern.flp is the boot floppy and mfsroot.flp is the root floppy. I don't know what fixit.flp is, I'm going to try that now, in case it's a fix for a bad boot-floppy ;-) OK, tried it, no difference. Ketil
Processing command-line options Opening VM (/dev/plex86) Processing config file conf.freebsd... Allocating 4MB of physical memory in VM Mapping virtualized physical memory into monitor Zeroing virtualized physical memory Mapping monitor print buffer into user mem. bochs: ips = 1000000 unmapped_c::init: IGNORING unmapped ports bochs: [cmos] Setting initial clock to: Sun Dec 10 02:07:20 2000 bochs: bx_options.floppy_command_delay = 500 vga construct static bochs: font_width = 8 bochs: font_height = 16 bochs: default_depth = 16 bochs: waiting for MapNotify bochs: MapNotify found. bochs: vga: interval=200000 vga init called bochs: TTY not used, serial port is not connected ROM: loading image 'bios/BIOS-plex86-2000_0817a' @ 0xf0000 (65536 bytes) ROM: loading image 'bios/VGABIOS-elpin-2.40' @ 0xc0000 (32768 bytes) Setting prescan depth to 3 prescan on Processed 62 lines of config file 'conf.freebsd' Initializing plugins Running VM bochs: timer0 period set to 18 hz bochs: CMOS: write reg 14h: value = 05h bochs: vga: io write: 3cf: reg 05: value = 10h bochs: vga: io write: 3da: ignoring: feature ctrl & vert sync bochs: *** io read 3c5 case 1: sequencer clocking mode bochs: vga: io write 3c0: address mode reg=16 bochs: vga: io write 3c0: address mode reg=17 bochs: vga: io write 3c0: address mode reg=18 bochs: vga: io write 3c0: address mode reg=19 bochs: vga: io write 3c0: address mode reg=20 bochs: *** io read 3c5 case 1: sequencer clocking mode bochs: vga: io write: 3cf: reg 05: value = 10h bochs: *** io read 3c5 case 1: sequencer clocking mode ::plex86 panic: ::HLT: CPL!=0 Fatal monitor error caused Panic eax:0x27f ebx:0x0 ecx:0x0 edx:0x0 ebp:0x0 esi:0x0 edi:0x0 esp:0x410 eflags:0x20202 eip:0x9138 cs:s=0x0, dl=0xffff, dh=0xfb00, valid=1 ss:s=0x9e7d, dl=0xe7d0ffff, dh=0xf309, valid=1 ds:s=0x0, dl=0xffff, dh=0xf300, valid=1 es:s=0x0, dl=0xffff, dh=0xf300, valid=1 fs:s=0x0, dl=0xffff, dh=0xf300, valid=1 gs:s=0x0, dl=0xffff, dh=0xf300, valid=1 ldtr:s=0x0, dl=0x0, dh=0x0, valid=0 tr:s=0x38, dl=0x1f982067, dh=0x8900, valid=1 gdtr:base=0x9660, limit=0x3f idtr:base=0x1e00, limit=0x197 dr0:0x0 dr1:0x0 dr2:0x0 dr3:0x0 dr6:0xffff0ff0 dr7:0x400 tr3:0x0 tr4:0x0 tr5:0x0 tr6:0x0 tr7:0x0 cr0:0x60000033 cr1:0x0 cr2:0x0 cr3:0x0 cr4:0x0 inhibit_mask:0 Stack dump: Current instruction: 0000.00009138 F4 hlt Shutting down plugins bochs: Note: X11: bx_gui_c::exit() not implemented yet. Unmapping guest physical memory. Unmapping monitor print buffer. Tearing down VM Closing VM
