Being new to this list and new to plex86, I don't know if this is a stupid question or not. My compile works fine but when I launch plex86, it dies and I get the following error. I do understand that the code base is not stable, and the code could be broken, or I could just be stupid.... :-) Any help would be greatly appreciated. Nick Rathke Processing command-line options Opening VM (/dev/plex86) Processing config file ../conf/winnt... Allocating 32MB of physical memory in VM Mapping virtualized physical memory into monitor Zeroing virtualized physical memory Mapping monitor print buffer into user mem. unmapped_c::init: IGNORING unmapped ports bochs: [cmos] Setting initial clock to: Thu Aug 23 17:41:48 2001 disk: Experimental CDROM on target 1 disk: Media present in CD-ROM drive #cdrom: capacity: 185688 bochs: Opening image for device 0 bochs: bx_options.floppy_command_delay = 500 vga construct static bochs: font_width = 8 bochs: font_height = 16 bochs: default_depth = 24 bochs: waiting for MapNotify bochs: MapNotify found. bochs: vga: interval=200000 vga init called bochs: TTY not used, serial port is not connected ROM: loading image '../bios/BIOS-plex86-current' @ 0xf0000 (65536 bytes) ROM: loading image '../bios/VGABIOS-elpin-2.40' @ 0xc0000 (32768 bytes) Setting prescan depth to 3 prescan on Processed 63 lines of config file '../conf/winnt' Initializing plugins Running VM ::init_monitor OK ----------------- nexus_size = 0x24E bochs: CMOS: write reg 14h: value = 05h ::sysIOOut: No handler defined for port 0x46E8!. ::sysIOOut: No handler defined for port 0x102!. ::sysIOOut: No handler defined for port 0x4AE8!. bochs: vga: io write: 3cf: reg 05: value = 10h bochs: vga: io write: 3da: ignoring: feature ctrl & vert sync bochs: *** io read 3c5 case 1: sequencer clocking mode bochs: vga: io write 3c0: address mode reg=16 bochs: vga: io write 3c0: address mode reg=17 bochs: vga: io write 3c0: address mode reg=18 bochs: vga: io write 3c0: address mode reg=19 bochs: vga: io write 3c0: address mode reg=20 bochs: *** io read 3c5 case 1: sequencer clocking mode bochs: vga: io write: 3cf: reg 05: value = 10h bochs: *** io read 3c5 case 1: sequencer clocking mode bochs: disk: enabling LBA mode ::plex86 panic: ::ENTER: level > 0 Fatal monitor error caused Panic eax:0x11f400 ebx:0x5d ecx:0x110000 edx:0x380 ebp:0xfff8 esi:0x4d edi:0x500 esp:0x7cfd eflags:0x83 eip:0x9fc45 cs:s=0x0, dl=0xffff, dh=0x9b00, valid=1 ss:s=0x0, dl=0xffff, dh=0x9300, valid=1 ds:s=0x0, dl=0xffff, dh=0x9300, valid=1 es:s=0x0, dl=0xffff, dh=0x9300, valid=1 fs:s=0x0, dl=0xffff, dh=0x9300, valid=1 gs:s=0x0, dl=0xffff, dh=0x9300, valid=1 ldtr:s=0x0, dl=0x0, dh=0x0, valid=0 tr:s=0x0, dl=0x0, dh=0x0, valid=0 gdtr:base=0x0, limit=0x0 idtr:base=0x0, limit=0x3ff dr0:0x0 dr1:0x0 dr2:0x0 dr3:0x0 dr6:0xffff0ff0 dr7:0x400 tr3:0x0 tr4:0x0 tr5:0x0 tr6:0x0 tr7:0x0 cr0:0x60000032 cr1:0x0 cr2:0x0 cr3:0x0 cr4:0x0 inhibit_mask:0 Stack dump: Current instruction: 0000.0009FC45 C8280A10 enter $0x0a28, $0x10 Shutting down plugins bochs: Note: X11: bx_gui_c::exit() not implemented yet. Unmapping guest physical memory. Unmapping monitor print buffer. Tearing down VM Closing VM
