Connect over a wire to the admin interface and confirm you are typing the wifi key correctly.
On Wed, Jun 19, 2019 at 3:00 PM logical american <[email protected]> wrote: > Hello > > I am trying to determine the best course of action to fix a password > authentication problem with the wireless router after a software update. > > After the software update yesterday for openSuse Leap 15.0 (64 bit) OS, > all of a sudden I could no longer connect with my WPA2-PSK wireless router. > > The wpa_supplicant log shows the following when trying to connect (a > password is asked for) : > > 1560974114.070337: wlan2: SME: Trying to authenticate with > 74:31:70:03:95:e4 (SSID='Puma_Bear' freq=2417 MHz) > 1560974114.097852: wlan2: Trying to associate with 74:31:70:03:95:e4 > (SSID='Puma_Bear' freq=2417 MHz) > 1560974114.105401: wlan2: Associated with 74:31:70:03:95:e4 > 1560974114.105426: wlan2: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0 > 1560974114.153187: wlan2: WPA: Failed to set GTK to the driver (alg=2 > keylen=32 keyidx=1) > 1560974114.153204: wlan2: RSN: Failed to configure GTK > 1560974114.163499: wlan2: CTRL-EVENT-DISCONNECTED > bssid=74:31:70:03:95:e4 reason=1 locally_generated=1 > 1560974114.163529: wlan2: CTRL-EVENT-SSID-TEMP-DISABLED id=0 > ssid="Puma_Bear" auth_failures=1 duration=10 reason=CONN_FAILED > 1560974114.175207: wlan2: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD > 1560974125.550043: wlan2: CTRL-EVENT-SSID-REENABLED id=0 ssid="Puma_Bear" > 1560974125.550214: wlan2: SME: Trying to authenticate with > 74:31:70:03:95:e4 (SSID='Puma_Bear' freq=2417 MHz) > 1560974125.576074: wlan2: Trying to associate with 74:31:70:03:95:e4 > (SSID='Puma_Bear' freq=2417 MHz) > 1560974125.581516: wlan2: Associated with 74:31:70:03:95:e4 > 1560974125.581541: wlan2: CTRL-EVENT-SUBNET-STATUS-UPDATE status=0 > 1560974125.610731: wlan2: WPA: Failed to set GTK to the driver (alg=2 > keylen=32 keyidx=1) > 1560974125.610748: wlan2: RSN: Failed to configure GTK > 1560974125.621047: wlan2: CTRL-EVENT-DISCONNECTED > bssid=74:31:70:03:95:e4 reason=1 locally_generated=1 > 1560974125.621076: wlan2: CTRL-EVENT-SSID-TEMP-DISABLED id=0 > ssid="Puma_Bear" auth_failures=2 duration=20 reason=CONN_FAILED > 1560974125.631411: wlan2: CTRL-EVENT-REGDOM-CHANGE init=CORE type=WORLD > 1560974138.371062: wlan2: Reject scan trigger since one is already pending > 1560974337.504917: rfkill: WLAN soft blocked > 1560974337.605744: nl80211: deinit ifname=wlan2 disabled_11b_rates=0 > > Careful reading of internet information shows that the error line > "Failed to set GTK to the driver" is a problem with password > authentication and/or setting. > > The wireless driver is nl80211 > > I tried the modprobe command to load up possible wlan modules, thinking > that perhaps the problem was a missing kernel module, but so far that > did not solve the problem. > > What would be a reasonable action? > > 1. Get onto the appropriate openSuse forum and ask around? > 2. Try to undo the software update? (this might be very difficult since > kernel changes occurred) > 3. Try to troubleshoot the wpa_supplicant program and dump a trail of > results? > > > The password for the router has not been changed, and it works okay with > another machine upon authenticating with the WPA2-PSK password, so I > have to assume that the problem is perhaps in the linux 4.12.14 Leap > 150.12.64 kernel missing the appropriate crypt module for wireless service? > > Thanks for any comments or observations. > > - Randall > > > _______________________________________________ > PLUG mailing list > [email protected] > http://lists.pdxlinux.org/mailman/listinfo/plug > _______________________________________________ PLUG mailing list [email protected] http://lists.pdxlinux.org/mailman/listinfo/plug
