Here is a bit more on this: I made a fresh install of 3.9, followed by just pkg_add hylafax. The behaviour is the same, at faxsetup / faxaddmodem flow control scheme it gets stuck. I also used another - also serial - modem type; it shows the identical behaviour. minicom sees the modem working okay: ATDT123435 dials out to 12345; and when I dial the phone, RING shows on the terminal screen.
[Once again, the same modem has worked for years on 3.3-3.5, same hylafax.] It's getting worse: I downloaded hylafax 4.3.0 (the lastest of a few weeks ago), patched its configure in vi to make it compile and install. Ran faxsetup / faxaddmodem and it does *not* stop at flow control. It doesn't find the preset modem-config; but in the end - after adding it to ttys - it answers the phone and receives a fax (alas, faulty, but that has probably to make with my horrible patch-ing; there's an EOL error.) All this is no solution, but *maybe* it rings some bell ... ?! Uwe On 7/10/06, Uwe Dippel <[EMAIL PROTECTED]> wrote:
This is astonishing, because the modem has been working earlier (on earlier OpenBSDs and earlier main boards). But now it doesn't work any longer, whatever I try, it stops at DTE-DCE flow control scheme [default]. I can still press enter or anything, but faxaddmodem waits indefinitely (for what ?). I also tried xonxoff and rtscts; with the same result. I also tried class 1; same result. (I use class 2 here, because this modem always worked well with class 2) I searched the archives and google; and found one similar occurrence: http://www.bsdforums.org/forums/showthread.php?t=34612 Is this a BSD-problem, eventually ? This is about what it does: .... Are these ok [yes]? Now we are going to probe the tty port to figure out the type of modem that is attached. This takes a few seconds, so be patient. Note that if you do not have the modem cabled to the port, or the modem is turned off, this may hang (just go and cable up the modem or turn it on, or whatever). Probing for best speed to talk to modem: 38400 OK. This modem looks to have support for Class 1 and 2. How should it be configured [1]? 2 Hmm, this looks like a Class 2 modem. Modem manufacturer is "PHILIPS". Modem model is "ROCKWELL 144DPI". DTE-DCE flow control scheme [default]? whatever I type here, it is echoed. But no DTE-DCE takes place. Any hint welcome, Uwe OpenBSD 3.9 (GENERIC) #617: Thu Mar 2 02:26:48 MST 2006 [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC cpu0: AMD Sempron(tm) Processor 3000+ ("AuthenticAMD" 686-class, 256KB L2 cache) 1.61 GHz cpu0: FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,SSE3 cpu0: AMD Powernow: TS TTP TM STC real mem = 469278720 (458280K) avail mem = 421019648 (411152K) using 4278 buffers containing 23568384 bytes (23016K) of memory mainbus0 (root) bios0 at mainbus0: AT/286+(05) BIOS, date 06/05/06, BIOS32 rev. 0 @ 0xfb300 apm0 at bios0: Power Management spec V1.2 apm0: AC on, battery charge unknown apm0: flags 70102 dobusy 1 doidle 1 pcibios0 at bios0: rev 3.0 @ 0xf0000/0xd324 pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfd200/256 (14 entries) pcibios0: PCI Exclusive IRQs: 5 10 11 pcibios0: no compatible PCI ICU found pcibios0: Warning, unable to fix up PCI interrupt routing pcibios0: PCI bus #4 is the last bus bios0: ROM list: 0xc0000/0xde00 0xd0000/0x4000! cpu0 at mainbus0 pci0 at mainbus0 bus 0: configuration mode 1 (no bios) "NVIDIA C51 Host" rev 0xa2 at pci0 dev 0 function 0 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 1 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 2 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 3 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 4 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 5 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 6 not configured "NVIDIA C51 Memory" rev 0xa2 at pci0 dev 0 function 7 not configured ppb0 at pci0 dev 2 function 0 "NVIDIA C51 PCIE" rev 0xa1 pci1 at ppb0 bus 1 ppb1 at pci0 dev 3 function 0 "NVIDIA C51 PCIE" rev 0xa1 pci2 at ppb1 bus 2 ppb2 at pci0 dev 4 function 0 "NVIDIA C51 PCIE" rev 0xa1 pci3 at ppb2 bus 3 vga1 at pci0 dev 5 function 0 "NVIDIA GeForce 6100" rev 0xa2 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) "NVIDIA MCP51 Host" rev 0xa2 at pci0 dev 9 function 0 not configured pcib0 at pci0 dev 10 function 0 "NVIDIA MCP51 ISA" rev 0xa3 "NVIDIA MCP51 SMBus" rev 0xa3 at pci0 dev 10 function 1 not configured "NVIDIA MCP51 Memory" rev 0xa3 at pci0 dev 10 function 2 not configured ohci0 at pci0 dev 11 function 0 "NVIDIA MCP51 USB" rev 0xa3: irq 10, version 1.0, legacy support usb0 at ohci0: USB revision 1.0 uhub0 at usb0 uhub0: NVIDIA OHCI root hub, rev 1.00/1.00, addr 1 uhub0: 8 ports with 8 removable, self powered ehci0 at pci0 dev 11 function 1 "NVIDIA MCP51 USB" rev 0xa3: irq 5 usb1 at ehci0: USB revision 2.0 uhub1 at usb1 uhub1: NVIDIA EHCI root hub, rev 2.00/1.00, addr 1 uhub1: 8 ports with 8 removable, self powered pciide0 at pci0 dev 13 function 0 "NVIDIA MCP51 IDE" rev 0xa1: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility pciide0: channel 0 disabled (no drives) atapiscsi0 at pciide0 channel 1 drive 1 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVDRRW GWA-4166B, 2.04> SCSI0 5/cdrom removable cd0(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2 ppb3 at pci0 dev 16 function 0 "NVIDIA MCP51 PCI-PCI" rev 0xa2 pci4 at ppb3 bus 4 eap0 at pci4 dev 7 function 0 "Ensoniq CT5880" rev 0x02: irq 5 ac97: codec id 0x83847609 (SigmaTel STAC9721/23) ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D audio0 at eap0 midi0 at eap0: <AudioPCI MIDI UART> "Texas Instruments TSB43AB23 FireWire" rev 0x00 at pci4 dev 14 function 0 not configured nfe0 at pci0 dev 20 function 0 "NVIDIA MCP51 LAN" rev 0xa3: irq 11, address 00:16:e6:4f:31:1e ukphy0 at nfe0 phy 1: Generic IEEE 802.3u media interface, rev. 1: OUI 0x005043, model 0x0021 pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00 pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00 pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00 pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00 isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pmsi0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pmsi0 mux 0 pcppi0 at isa0 port 0x61 midi1 at pcppi0: <PC speaker> spkr0 at pcppi0 lpt0 at isa0 port 0x378/4 irq 7 it0 at isa0 port 0x290/8: IT87 npx0 at isa0 port 0xf0/16: using exception 16 pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec biomask e76d netmask ef6d ttymask ffef pctr: user-level cycle counter enabled umass0 at uhub1 port 4 configuration 1 interface 0 umass0: Cypress Semiconductor USB2.0 Storage Device, rev 2.00/0.01, addr 2 umass0: using SCSI over Bulk-Only scsibus1 at umass0: 2 targets sd0 at scsibus1 targ 1 lun 0: <ST325082, 4A, 0 0> SCSI0 0/direct fixed sd0: 238474MB, 238474 cyl, 64 head, 32 sec, 512 bytes/sec, 488395055 sec total dkcsum: sd0 matches BIOS drive 0x80 root on sd0a rootdev=0x400 rrootdev=0xd00 rawdev=0xd02
