However, doing the uninstall followed by the full install works on Win 10. On Fri, May 1, 2020 at 11:22 PM Devon McCormick <[email protected]> wrote:
> I tried "install 'full'" both before and after "'remove' jpkg 'qtide'" but > still have the slim JQt. This is on Win7. > > On Fri, May 1, 2020 at 10:31 PM bill lam <[email protected]> wrote: > >> Perhaps the slim version already installed. you can force it to the full >> version by >> install 'full' >> >> >> On Sat, May 2, 2020 at 10:18 AM Don Guinn <[email protected]> wrote: >> >> > I did the install. Tried JQt. Still failed. Rebooted. SYSINFO still >> showed >> > "s". So I ran the install again and noticed it said was installing the >> "s" >> > version. I had seen this before where for some reason running the >> install >> > 'qtide' doesn't always work. That's why I asked about how to tell what >> > version was actually installed. >> > >> > If you need more details on what I did, pleas let me know. >> > >> > On Fri, May 1, 2020 at 4:14 PM 'robert therriault' via Programming < >> > [email protected]> wrote: >> > >> > > Hi Don, >> > > >> > > If you do >> > > >> > > JVERSION >> > > Engine: j807/j64/darwin >> > > Release-d: commercial/2019-03-18T16:07:14 >> > > Library: 8.07.26 >> > > Qt IDE: 1.7.9/5.9.6 >> > > Platform: Darwin 64 >> > > Installer: J807 install >> > > InstallPath: /users/bobtherriault/j64-807 >> > > Contact: www.jsoftware.com >> > > >> > > On the Qt IDE line you will see an 's' in the ID if it is the slim >> > > version. On my line above it has 1.7.9/5.9.6 because it is the full >> > version >> > > (no 's') >> > > >> > > You do have to restart J in order for the updated Qt to take effect. >> > > >> > > Hope this helps. >> > > >> > > Cheers, bob >> > > >> > > > On May 1, 2020, at 15:07, Don Guinn <[email protected]> wrote: >> > > > >> > > > Thank you. I installed it as you said, but when I ran the webview >> demo >> > I >> > > > still got the same message. How can I tell if I actually have the >> full >> > > > version of JQt installed? >> > > > >> > > > On Fri, May 1, 2020 at 2:56 PM Norman Drinkwater < >> > [email protected] >> > > > >> > > > wrote: >> > > > >> > > >> You have the slim version of jqt installed. Webview requires the >> full >> > > jqt >> > > >> version. You should be able to upgrade to the full version from >> > > jconsole. >> > > >> First load’pacman’, then install’qtide’. >> > > >> >> > > >> On Fri, May 1, 2020 at 3:41 PM Don Guinn <[email protected]> >> wrote: >> > > >> >> > > >>> A while back webview was considered "experimental". It is >> appearing >> > in >> > > >> more >> > > >>> and more J tools. For example: The jig tool. Is it now a supported >> > > >> control >> > > >>> in J? >> > > >>> >> > > >>> There also appears that some versions of Windows do not support >> > > webview. >> > > >>> The QtDemos/webview fails on some versions of Windows, one with >> the >> > > >>> message, "Win 1.6.7s/5.12.7/(5.12.7_ is not supported". I could >> not >> > > find >> > > >>> any information searching on "webview" on the internet. Can anyone >> > tell >> > > >> me >> > > >>> what is needed in Windows to make webview work? >> > > >>> >> > > >>> Also, Guides/JQtChildClasses#webview lists several events from the >> > > >> webview >> > > >>> control. I do not see any events from webview in wdq. Is there >> > > something >> > > >>> needed to get those events activated? >> > > >>> >> > ---------------------------------------------------------------------- >> > > >>> For information about J forums see >> > http://www.jsoftware.com/forums.htm >> > > >>> >> > > >> >> ---------------------------------------------------------------------- >> > > >> For information about J forums see >> > http://www.jsoftware.com/forums.htm >> > > >> >> > > > >> ---------------------------------------------------------------------- >> > > > For information about J forums see >> http://www.jsoftware.com/forums.htm >> > > >> > > ---------------------------------------------------------------------- >> > > For information about J forums see >> http://www.jsoftware.com/forums.htm >> > > >> > ---------------------------------------------------------------------- >> > For information about J forums see http://www.jsoftware.com/forums.htm >> > >> ---------------------------------------------------------------------- >> For information about J forums see http://www.jsoftware.com/forums.htm >> > > > -- > > Devon McCormick, CFA > > Quantitative Consultant > > -- Devon McCormick, CFA Quantitative Consultant ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
