Same experience here, rather annoying. Will plan an uninstall later.
R.E Boss -----Original Message----- From: Programming <[email protected]> On Behalf Of Don Guinn Sent: zaterdag 2 mei 2020 04:18 To: Programming forum <[email protected]> Subject: Re: [Jprogramming] Status of webview I did the install. Tried JQt. Still failed. Rebooted. SYSINFO still showed "s". So I ran the install again and noticed it said was installing the "s" version. I had seen this before where for some reason running the install 'qtide' doesn't always work. That's why I asked about how to tell what version was actually installed. If you need more details on what I did, pleas let me know. On Fri, May 1, 2020 at 4:14 PM 'robert therriault' via Programming < [email protected]> wrote: > Hi Don, > > If you do > > JVERSION > Engine: j807/j64/darwin > Release-d: commercial/2019-03-18T16:07:14 > Library: 8.07.26 > Qt IDE: 1.7.9/5.9.6 > Platform: Darwin 64 > Installer: J807 install > InstallPath: /users/bobtherriault/j64-807 > Contact: www.jsoftware.com > > On the Qt IDE line you will see an 's' in the ID if it is the slim > version. On my line above it has 1.7.9/5.9.6 because it is the full > version (no 's') > > You do have to restart J in order for the updated Qt to take effect. > > Hope this helps. > > Cheers, bob > > > On May 1, 2020, at 15:07, Don Guinn <[email protected]> wrote: > > > > Thank you. I installed it as you said, but when I ran the webview > > demo I still got the same message. How can I tell if I actually have > > the full version of JQt installed? > > > > On Fri, May 1, 2020 at 2:56 PM Norman Drinkwater > > <[email protected] > > > > wrote: > > > >> You have the slim version of jqt installed. Webview requires the > >> full > jqt > >> version. You should be able to upgrade to the full version from > jconsole. > >> First load’pacman’, then install’qtide’. > >> > >> On Fri, May 1, 2020 at 3:41 PM Don Guinn <[email protected]> wrote: > >> > >>> A while back webview was considered "experimental". It is > >>> appearing in > >> more > >>> and more J tools. For example: The jig tool. Is it now a supported > >> control > >>> in J? > >>> > >>> There also appears that some versions of Windows do not support > webview. > >>> The QtDemos/webview fails on some versions of Windows, one with > >>> the message, "Win 1.6.7s/5.12.7/(5.12.7_ is not supported". I > >>> could not > find > >>> any information searching on "webview" on the internet. Can anyone > >>> tell > >> me > >>> what is needed in Windows to make webview work? > >>> > >>> Also, Guides/JQtChildClasses#webview lists several events from the > >> webview > >>> control. I do not see any events from webview in wdq. Is there > something > >>> needed to get those events activated? > >>> ------------------------------------------------------------------ > >>> ---- For information about J forums see > >>> http://www.jsoftware.com/forums.htm > >>> > >> ------------------------------------------------------------------- > >> --- For information about J forums see > >> http://www.jsoftware.com/forums.htm > >> > > -------------------------------------------------------------------- > > -- For information about J forums see > > http://www.jsoftware.com/forums.htm > > ---------------------------------------------------------------------- > For information about J forums see http://www.jsoftware.com/forums.htm > ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
