You are right about giving a chance for viewmat to update the screen. For sequence of images I suggested animate addon in the link below.
Also you may try wd'msgs'. Oleg On Dec 15, 2008, at 0:31, "Devon McCormick" <[email protected]> wrote: Dr. Brouwer - I think this is not so much a Vista 64-bit problem but a general problem with the event-loop/message-pump handling. I've encountered this problem before: I have a sequence of lines of code that work fine in immediate execution but fail when they're in a function. I believe the problem is that viewmat needs to get to a state of waiting for user input before it will finish displaying its picture. This doesn't happen within multiple lines in a function, so only a blank picture is saved. I've tried lots of different ways to get around this and have settled on using the "image3" add-on to write my images instead of relying on viewmat. This is too bad because viewmat does offer a nice display of complex numbers that I haven't replicated with image3 code. This problem is also mentioned by Dan Bron at http://www.jsoftware.com/jwiki/DanBron/Snippets/PrettyPictures and even Oleg doesn't have a solution. Regards, Devon** On Sun, Dec 14, 2008 at 12:54 PM, Roelof K Brouwer <[email protected]>wrote: I have problems with viewmat save in vista 64bit. In particular the following two statements ( 1 4 14 {". COLOR16) viewmat i.4 4 savemat_jviewmat_ 'C:\Temp\garbage.bmp' this will give a blank window when used in a verb and also in ijx when debug is in sometimes by adjusting the viewmat window I will get the proper display . i.e. click the margin of the window for exdpansion. However sometimes on expansion the window does not have the correct displayI if I remove the save command things will work when in ijx I can first run viewmat command and then the save command and things will work I also tried puttting a delay between the two viewmat commands here is my complete file with verb drivedata=: 'C:\Users\RKBrouwer\Documents\ACA\Research\ResData\' drive_op=:'C:\Users\RKBrouwer\Documents\Temp\Set\' drive=:'C:\Users\RKBrouwer\Documents\ACA\' require 'viewmat color16 plot' load 'C:\Users\RKBrouwer\Documents\J_Code_Roelof\J_utilities_roelof.ijs' NB. load 'C:\Users\RKBrouwer\Documents\J_utilities_roelof\visual_clustering.ijs' require 'jfiles' test_viewmat=:3 : 0 ( 1 4 14 {". COLOR16) viewmat i.4 4 savemat_jviewmat_ 'C:\Temp\garbage.bmp' ) cheers Roelof "Have a cool mind and a warm heart" - Ajahn Sona "Like ......(hamsters on a wheel), (ambitious people) still climb and climb, with great labor, and incessant anxiety, but never reach the top." Robert Browning "We shall not cease from exploration. And at the end of all our exploring Will be to arrive were we started and know the place for the first time" - T. S. Eliot Dr. Roelof K. Brouwer PH.D. P.Eng. Professor Emeritus Dept. of Computing Science School of Advanced Technologies and Mathematics Thompson Rivers University 900 McGill Road Kamloops, BC Canada, V2C 5N3 email : <mailto:[email protected]> [email protected] <http://www.tru.ca/advtech/compsci/faculty/rbrouwer> www.tru.ca/advtech/compsci/faculty/rbrouwer ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm -- Devon McCormick, CFA ^me^ at acm. org is my preferred e-mail ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm ---------------------------------------------------------------------- For information about J forums see http://www.jsoftware.com/forums.htm
