About 3D.

Visit www.qualecad.com and try 3D Viewer from it. 3D models for it are
created in Solidworks then converted into OpenGL format.
Very pretty add-on.

Best regards,
Yuri V.Potapoff
technical expert
Rodnik Software, Inc.
1 Nakhimovsky ave., bldg.1, Moscow, 113556 Russia
Phones: +7 (095) 113-2688; +7 (095) 113-7001
Fax:    +7 (095) 317-9754
E-mail: [EMAIL PROTECTED]
http://www.rodnik.ru






> ----------
> From:         Rolf Molitor[SMTP:[EMAIL PROTECTED]]
> Sent:         Monday, September 03, 2001 12:37:19 PM
> To:   Protel EDA Forum
> Subject:      Re: [PEDA] Simulation Parameter Sweeps
> Auto forwarded by a Rule
> 
> It is a bug.
> I hope that the simulator and especially its viewer will receive some
> serious improvement in the next service pack. There was almost none up to
> SP6. Its time.
> Same to the 3D tool. If there only were some more default models (and a
> description how to make them show up), the tool would be much much more
> useful. I am getting angry when i see these ugly grey boxes and can not do
> anything against them. What about a handful of additional models in every
> SP
> ? That shouldnt be to difficult ?
> 
> 
> Rolf Molitor
> Systemelektronik i2e
> Remscheid / Germany
> 
> -----Ursprüngliche Nachricht-----
> Von: <[EMAIL PROTECTED]>
> An: "proteledaforum" <[EMAIL PROTECTED]>
> Gesendet: Sonntag, 2. September 2001 16:02
> Betreff: [PEDA] Simulation Parameter Sweeps
> 
> 
> When I select the Relative Values checkbox (and change the Start & Stop
> Values) before sweeping a resistor value, I no-longer get the result for
> each pass displayed as an available waveform! The multiple passes are
> still
> performed, but there is only a single waveform generated. If I uncheck the
> checkbox and enter absolute values, it is OK!
> Is this a bug, feature, or my misunderstanding?
> 
> Thanks,
> Steve
> Posted from Association web site by: Steven Beames
> 
> 
> 
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
> * To post a message: mailto:[EMAIL PROTECTED]
> *
> * To leave this list visit:
> * http://www.techservinc.com/protelusers/leave.html
> *
> * Contact the list manager:
> * mailto:[EMAIL PROTECTED]
> *
> * Forum Guidelines Rules:
> * http://www.techservinc.com/protelusers/forumrules.html
> *
> * Browse or Search previous postings:
> * http://www.mail-archive.com/proteledaforum@techservinc.com
> * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
* To post a message: mailto:[EMAIL PROTECTED]
*
* To leave this list visit:
* http://www.techservinc.com/protelusers/leave.html
*
* Contact the list manager:
* mailto:[EMAIL PROTECTED]
*
* Forum Guidelines Rules:
* http://www.techservinc.com/protelusers/forumrules.html
*
* Browse or Search previous postings:
* http://www.mail-archive.com/proteledaforum@techservinc.com
* * * * * * * * * * * * * * * * * * * * * * * * * * * * * *

Reply via email to