> We use "\". In PCAD you can type it once at the end. > In Protel you have to type it after each character to > get the same but it's possible. I don't see any > problems with Protel itself.
it doesn't read well when it is a net label and stacked up on wires i am starting to think i like the suffix # approach if you use a PREFIX such as n_WRITE then your net labels list is sorted by the negation character in front which doesn't really make sense the suffix "#" is a normal but distinctive character and leaves the sense of the name alone in a sorted list AND it saves a precious character space Cliff, in my book you da man! case closed, at least for me Dennis Saputelli Mira wrote: > > Hi, > > We use "\". In PCAD you can type it once at the end. > In Protel you have to type it after each character to > get the same but it's possible. I don't see any > problems with Protel itself. > > Mira > > --- Cliff Gerhard <[EMAIL PROTECTED]> wrote: > > We use a "#" after the signal name ala the PCI > > specification (GNT#, REQ#, > > etc.) > > > > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ > > Cliff Gerhard, P.E. > > E-M Designs, Inc. > > PH 949.661.3016 x 501 > > www.gerhardeng.com > > www.emdesigns.com > > www.emmanufacturing.com > > > > > > > > -----Original Message----- > > From: Dennis Saputelli > > [mailto:[EMAIL PROTECTED]] > > Sent: Saturday, June 01, 2002 10:58 AM > > To: Protel EDA Forum > > Subject: Re: [PEDA] negation character redux > > > > > > I know this has been widely discussed but ... > > > > re: > > pin naming on schematic symbols and the negation > > character thereof > > > > what was the consensus, or was there? > > i know the bar symbol is problematic and i have > > decided to never use it > > again > > > > i recall someone advocating the use of "n" as in nRW > > that doesn't look too bad but what about "*" or "-" > > > > i was scared to use those without some advice that > > those characters were > > not problematic > > (sometimes this sort of thing doesn't bite you until > > late in the game) > > > > as a functional issue i guess this question is > > probably more importantly > > applied to net labels than schem pin names > > but i think they should be done consistently > > > > Dennis Saputelli > > > > -- > > > ___________________________________________________________________________ > > www.integratedcontrolsinc.com Integrated > > Controls, Inc. > > tel: 415-647-0480 2851 > > 21st Street > > fax: 415-647-3003 San > > Francisco, CA 94110 > > > > * * * * * * * * * * * * * * * * * * * * * * * * * * > > * * * * > > * To post a message: > > mailto:[EMAIL PROTECTED] > > * > > * To leave this list visit: > > * http://www.techservinc.com/protelusers/leave.html > > * > > * Contact the list manager: > > * mailto:[EMAIL PROTECTED] > > * > > * Forum Guidelines Rules: > > * > > > http://www.techservinc.com/protelusers/forumrules.html > > * > > * Browse or Search previous postings: > > * > > > http://www.mail-archive.com/proteledaforum@techservinc.com > > * * * * * * * * * * * * * * * * * * * * * * * * * * > > * * * * > > __________________________________________________ > Do You Yahoo!? > Yahoo! - Official partner of 2002 FIFA World Cup > http://fifaworldcup.yahoo.com -- ___________________________________________________________________________ www.integratedcontrolsinc.com Integrated Controls, Inc. tel: 415-647-0480 2851 21st Street fax: 415-647-3003 San Francisco, CA 94110 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To leave this list visit: * http://www.techservinc.com/protelusers/leave.html * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * Forum Guidelines Rules: * http://www.techservinc.com/protelusers/forumrules.html * * Browse or Search previous postings: * http://www.mail-archive.com/proteledaforum@techservinc.com * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
