Hi Benedikt,

when you get to the barebox boot prompt, can you boot successfully by typing "boot mmc0"?

In your logs I can see that barebox is adding the wrong rootfs option to the kernel command line, it probably wasn't enough to specify global.bootm.* variables. The "boot mmc0" command should autodetect the respective command line options for the kernel.

By the way, you can set the default boot target in barebox with
"nv boot.default=mmc0", followed by a reset. I think the barebox defaultenv sets this variable wrong on boot...

 - Roland

On 22.03.2018 18:11, Robert Schwebel wrote:
----- Forwarded message from [email protected] -----

Date: Thu, 22 Mar 2018 15:12:24 +0100
From: [email protected]
To: [email protected]
Subject: Auto-discard notification
Message-ID: <[email protected]>

The attached message has been automatically discarded.

Date: Thu, 22 Mar 2018 14:12:21 +0000
From: [email protected]
To: [email protected]
Subject: DistroKit not working for BeagleCore
Message-ID: <[email protected]>
X-Mailer: Lotus Notes Release 8.5.1FP1 January 05, 2010

Hi *,

I wanted to feel the power of ptxdist and tried to build an image for
beaglecore (which is a beaglebone black) with DistroKit-2018.03.0 and
OSELAS.Toolchain-2016.06.1/arm-v7a-linux-gnueabihf Toolchain.

Unfortunately nothing is really working. The Boot Process is stopping here:

barebox 2018.01.0-20180128-1 #1 Thu Mar 22 13:13:28 UTC 2018

Board: TI AM335x BeagleBone black

detected 'BeagleBone Black'

cpsw 4a100000.ethernet: detected phy mask 0x1

mdio_bus: miibus0: probed

eth0: got preset MAC address: b0:d5:cc:cb:83:00

cpsw 4a100000.ethernet: Failed to setup slave 1: I/O error

am335x-phy-driver 47401300.usb-phy: am_usbphy 8ffa9528 enabled

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO
Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

am335x-phy-driver 47401b00.usb-phy: am_usbphy 8ffaaa88 enabled

musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO
Rx, HB-ISO Tx, SoftConn)

musb-hdrc: MHDRC RTL version 2.0

musb-hdrc: setup fifo_mode 4

musb-hdrc: 28/31 max ep, 16384/16384 memory

i2c-omap 44e0b000.i2c: bus 0 rev0.11 at 400 kHz

omap-hsmmc 48060000.mmc: registered as 48060000.mmc

mmc0: detected SD card version 2.0

mmc0: registered mmc0

omap-hsmmc 481d8000.mmc: registered as 481d8000.mmc

mmc1: detected MMC card version 4.5

mmc1: registered mmc1

netconsole: registered as netconsole-1

malloc space: 0x8fefeee0 -> 0x9fdfddbf (size 255 MiB)

environment load /mnt/mmc0.0/barebox.env: No such file or directory

Maybe you have to create the partition.

running /env/bin/init...

[?25hchanging USB current limit to 1300 mA... done

Hit m for menu or any other key to stop autoboot:    3       2       1       0

bootchooser: Target list $global.bootchooser.targets is empty

Nothing bootable found on 'bootchooser'

booting 'net'

ip_route_get: No such file or directory

could not open /mnt/tftp/none-linux-generic: No route to host

Booting 'net' failed: No route to host

booting 'net' failed: No route to host

boot: No route to host

type exit to get to the menu

[1;32mbarebox@[1;36mTI AM335x BeagleBone black:

When trying to boot manually with (global.bootm.image=/mnt/mmc0.1/boot/zImage,
global.bootm.oftree=/mnt/mmc0.1/boot/am335x-boneblack.dtb):

Loading ARM Linux zImage '/mnt/mmc0.1/boot/zImage'

Loading devicetree from '/mnt/mmc0.1/boot/am335x-boneblack.dtb'

commandline: console=ttyO0,115200 console=ttyO0,115200n8  root=/dev/nfs nfsroot
=/home/none/nfsroot/generic,v3,tcp loglevel=5 systemd.log_level=warning
systemd.show_status=auto

[    0.003601] timer_probe: no matching timers found

[    0.245969] omap_hwmod: debugss: _wait_target_disable failed

[    0.533505] hw perfevents: no interrupt-affinity property for /pmu,
guessing.

[    0.836376] omap_voltage_late_init: Voltage driver support not added

[    0.871536] mmc0: host does not support reading read-only switch, assuming
write-enable

[    0.915997] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 500000
KHz

[    0.924074] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency
changed to: 600000 KHz

[    0.935105] Root-NFS: no NFS server address

[    0.940012] VFS: Unable to mount root fs via NFS, trying floppy.

[    0.949346] VFS: Cannot open root device "nfs" or unknown-block(2,0): error
-6

[    0.956876] Please append a correct "root=" boot option; here are the
available partitions:

[    0.965846] b300        15558144 mmcblk0

[    0.965855]  driver: mmcblk

[    0.973123]   b301           32768 mmcblk0p1 abe26147-01

[    0.973130]

[    0.980386]   b302          524288 mmcblk0p2 abe26147-02

[    0.980392]

[    0.987474]   b303          524288 mmcblk0p3 abe26147-03

[    0.987479]

[    0.994764] Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(2,0)

Does anybody know how to get this DEMO Case working?

Regards

Benedikt


━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━━

_______________________________________________________________________

REHAU AG + Co, Kommanditgesellschaft;
Persoenlich haftende Gesellschafterin: Helmut Wagner AG 3074 Muri b. Bern,
Schweiz;
Praesident des Verwaltungsrats: Helmut Wagner, HR Bern CHE-107.882.879;
Sitz der Gesellschaft: Rehau;
Registergericht: Hof, HRA 2232


----- End forwarded message -----


--
Pengutronix e.K.                  | Roland Hieber               |
Industrial Linux Solutions        | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim | Phone: +49-5121-206917-5086 |
Amtsgericht Hildesheim, HRA 2686  | Fax:   +49-5121-206917-5555 |

_______________________________________________
ptxdist mailing list
[email protected]

Reply via email to