From: Mikel Astiz <[email protected]>
It might happen that a PropertyChanged signal is received but the
corresponding card profile has not been created, leading to an assertion
failure in filter_cb() due to inexistent ports. This can happen if BlueZ
misbehaves, or also if the UUIDs are reported later on (i.e. during
pairing discovery). In any case, the signal should just be ignored.
---
src/modules/bluetooth/module-bluetooth-device.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/src/modules/bluetooth/module-bluetooth-device.c
b/src/modules/bluetooth/module-bluetooth-device.c
index 82d81b3..5a035d1 100644
--- a/src/modules/bluetooth/module-bluetooth-device.c
+++ b/src/modules/bluetooth/module-bluetooth-device.c
@@ -1360,7 +1360,7 @@ static DBusHandlerResult filter_cb(DBusConnection *bus,
DBusMessage *m, void *us
} else if (dbus_message_is_signal(m, "org.bluez.HandsfreeGateway",
"PropertyChanged")) {
pa_bt_audio_state_t state = parse_state_property_change(m);
- if (state != PA_BT_AUDIO_STATE_INVALID) {
+ if (state != PA_BT_AUDIO_STATE_INVALID &&
pa_hashmap_get(u->card->profiles, "hfgw")) {
pa_device_port *port;
pa_port_available_t available = audio_state_to_availability(state);
@@ -1376,7 +1376,7 @@ static DBusHandlerResult filter_cb(DBusConnection *bus,
DBusMessage *m, void *us
} else if (dbus_message_is_signal(m, "org.bluez.Headset",
"PropertyChanged")) {
pa_bt_audio_state_t state = parse_state_property_change(m);
- if (state != PA_BT_AUDIO_STATE_INVALID) {
+ if (state != PA_BT_AUDIO_STATE_INVALID &&
pa_hashmap_get(u->card->profiles, "hsp")) {
pa_device_port *port;
pa_port_available_t available = audio_state_to_availability(state);
@@ -1392,7 +1392,7 @@ static DBusHandlerResult filter_cb(DBusConnection *bus,
DBusMessage *m, void *us
} else if (dbus_message_is_signal(m, "org.bluez.AudioSource",
"PropertyChanged")) {
pa_bt_audio_state_t state = parse_state_property_change(m);
- if (state != PA_BT_AUDIO_STATE_INVALID) {
+ if (state != PA_BT_AUDIO_STATE_INVALID &&
pa_hashmap_get(u->card->profiles, "a2dp_source")) {
pa_device_port *port;
pa_port_available_t available = audio_state_to_availability(state);
@@ -1405,7 +1405,7 @@ static DBusHandlerResult filter_cb(DBusConnection *bus,
DBusMessage *m, void *us
} else if (dbus_message_is_signal(m, "org.bluez.AudioSink",
"PropertyChanged")) {
pa_bt_audio_state_t state = parse_state_property_change(m);
- if (state != PA_BT_AUDIO_STATE_INVALID) {
+ if (state != PA_BT_AUDIO_STATE_INVALID &&
pa_hashmap_get(u->card->profiles, "a2dp")) {
pa_device_port *port;
pa_port_available_t available = audio_state_to_availability(state);
--
1.7.11.4
_______________________________________________
pulseaudio-discuss mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/pulseaudio-discuss
