Dimitri, hello
Thank you with you share
My Proxmox is proxmox-ve: 6.4-1 (running kernel: 5.4.143-1-pve)
I try change allow-vmbr0 with auto.
I found the link
https://metadata.ftp-master.debian.org/changelogs/main/o/openvswitch/testing_openvswitch-switch.README.Debian
In section ex 9: Bond + Bridge + VLAN + MTU allow is used.
But nothing wrong I try allow and auto, just comment one line.
Dimitri, thanks again for you share.
21.01.2022 15:03, Dimitri Alexandris пишет:
I have Openvswitch bonds working fine for years now, but in older versions
of Proxmox (6.4-4 and 5.3-5):
--------------
auto eno2
iface eno2 inet manual
auto eno1
iface eno1 inet manual
allow-vmbr0 ath
iface ath inet static
address 10.NN.NN.38/26
gateway 10.NN.NN.1
ovs_type OVSIntPort
ovs_bridge vmbr0
ovs_options tag=100
.
.
allow-vmbr0 bond0
iface bond0 inet manual
ovs_bonds eno1 eno2
ovs_type OVSBond
ovs_bridge vmbr0
ovs_options bond_mode=balance-slb lacp=active
allow-ovs vmbr0
iface vmbr0 inet manual
ovs_type OVSBridge
ovs_ports bond0 ath lan dmz_vod ampr
--------
I think now, "allow-vmbr0" and "allow-ovs" are replaced with "auto".
This bond works fine with HP, 3COM, HUAWEI, and MIKROTIK switches.
Several OVSIntPort VLANS are attached to it.
I also had 10G bonds (Intel, Supermicro inter-server links), with the same
result.
I see the only difference with your setup is the bond_mode. Switch setup
is also very important to match this.
On Fri, Jan 21, 2022 at 1:23 PM Сергей Цаболов<[email protected]> wrote:
Hello,
I have PVE cluster and I thinking to install on the pve-7 openvswitch
for can move and add VM from other networks and Proxmox Cluster
With base Linux bridge all work well without problem with 2 interface
10GB ens1f0np0 ens1f12np0
I install openvswitch with manual
https://pve.proxmox.com/wiki/Open_vSwitch
I want use Fiber 10GB interfaces ens1f0np0 ens1f12np0 with Bond I think.
I try some settings but is not working.
My setup in interfaces:
auto lo
iface lo inet loopback
auto ens1f12np0
iface ens1f12np0 inet manual
#Fiber
iface idrac inet manual
iface eno2 inet manual
iface eno3 inet manual
iface eno4 inet manual
auto ens1f0np0
iface ens1f0np0 inet manual
iface eno1 inet manual
auto inband
iface inband inet static
address 10.10.29.10/24
gateway 10.10.29.250
ovs_type OVSIntPort
ovs_bridge vmbr0
#Proxmox Web Access
auto vlan10
iface vlan10 inet manual
ovs_type OVSIntPort
ovs_bridge vmbr0
ovs_options tag=10
#Network 10
auto bond0
iface bond0 inet manual
ovs_bonds ens1f0np0 ens1f12np0
ovs_type OVSBond
ovs_bridge vmbr0
ovs_mtu 9000
ovs_options bond_mode=active-backup
auto vmbr0
iface vmbr0 inet manual
ovs_type OVSBridge
ovs_ports bond0 inband vlan10
ovs_mtu 9000
#inband
Can some one help me if I set all correctly or not?
If someone have setup openvswitch with Bond interfaces 10GB share with
me configuration.
Thank at lot.
Sergey TS
The best Regard
_______________________________________________
pve-user mailing list
[email protected]
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
_______________________________________________
pve-user mailing list
[email protected]
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
_______________________________________________
pve-user mailing list
[email protected]
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
Sergey TS
The best Regard
_______________________________________________
pve-user mailing list
[email protected]
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
_______________________________________________
pve-user mailing list
[email protected]
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-user
