Hi, I picked up a second-hand Wintv unit and am trying to configure it for Mythbuntu. I'm running the Intrepid release - 2.6.27-7... This apparently has all drivers and relevent firmware for my 29xxx version device.
The output of dmesg | tail -n 50 gives me: 284.964028] usb 4-2: new high speed USB device using ehci_hcd and address 3 [ 285.099348] usb 4-2: configuration #1 chosen from 1 choice [ 285.229450] msp3400' 3-0040: MSP3415G-B8 found @ 0x80 (pvrusb2_a) [ 285.229456] msp3400' 3-0040: msp3400 supports nicam and radio, mode is autode tect and autoselect [ 285.287828] saa7115' 3-0021: saa7115 found (1f7115d0e100000) @ 0x42 (pvrusb2_ a) [ 285.445331] tuner' 3-0061: chip found @ 0xc2 (pvrusb2_a) [ 285.473581] tveeprom 3-0050: Hauppauge model 29035, rev C324, serial# 6586214 [ 285.473587] tveeprom 3-0050: tuner model is Philips FM1246 (idx 24, type 1) [ 285.473590] tveeprom 3-0050: TV standards PAL(I) (eeprom 0x10) [ 285.473592] tveeprom 3-0050: audio processor is MSP3415 (idx 6) [ 285.473595] tveeprom 3-0050: decoder processor is SAA7115 (idx 19) [ 285.473600] tveeprom 3-0050: has radio, has IR receiver, has no IR transmitte r [ 285.473605] pvrusb2: Supported video standard(s) reported available in hardwa re: PAL-I [ 285.473608] pvrusb2: Mapping standards mask=0x10 (PAL-I) [ 285.473611] pvrusb2: Setting up 1 unique standard(s) [ 285.473616] pvrusb2: Set up standard idx=0 name=PAL-I [ 285.473619] pvrusb2: Initial video standard guessed as PAL-I [ 285.473627] pvrusb2: Device initialization completed successfully. [ 285.473766] pvrusb2: registered device video0 [mpeg] [ 285.473797] pvrusb2: registered device radio0 [mpeg] [ 285.546330] tuner-simple 3-0061: creating new instance [ 285.546339] tuner-simple 3-0061: type set to 1 (Philips PAL_I (FI1246 and com patibles)) [ 285.658711] msp3400' 3-0040: msp3400 rev1 = 0x0207 rev2 = 0x0f48 [ 285.658717] msp3400' 3-0040: Audio: volume 62000 [ 285.658720] msp3400' 3-0040: Audio: balance 0 bass 0 treble 0 loudness off [ 285.658724] msp3400' 3-0040: Standard: autodetect start (mono) [ 285.658727] msp3400' 3-0040: Audmode: 0x0001 [ 285.658731] msp3400' 3-0040: Routing: 0x00000000 (input) 0x00000044 (output) [ 285.658733] msp3400' 3-0040: ACB: 0x0c00 [ 285.658736] saa7115' 3-0021: Audio frequency: 48000 Hz [ 285.660453] saa7115' 3-0021: Input: Composite 4 [ 285.660455] saa7115' 3-0021: Video signal: bad [ 285.660457] saa7115' 3-0021: Frequency: 50 Hz [ 285.660460] saa7115' 3-0021: Detected format: BW/No color [ 285.660464] saa7115' 3-0021: Width, Height: 720, 480 [ 285.660467] tuner' 3-0061: Tuner mode: analog TV [ 285.660469] tuner' 3-0061: Frequency: 175.25 MHz [ 285.660471] tuner' 3-0061: Standard: 0x00000010 [ 285.660478] firmware: requesting v4l-cx2341x-enc.fw ...which as far as I can make out with my limited knowledge but from two days of googling is all good. However, running mplayer /dev/video0 just gives me: MPlayer 1.0rc2-4.3.2 (C) 2000-2007 MPlayer Team CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 4200+ (Family: 15, Model: 43, Stepping: 1) CPUflags: MMX: 1 MMX2: 1 3DNow: 1 3DNow2: 1 SSE: 1 SSE2: 1 Compiled with runtime CPU detection. Playing /dev/video0. ..though no mplayer window opens. When I hit ctrl+c I get: MPlayer interrupted by signal 2 in module: demux_open Running scantv just gives me a whole pile of 'no station' results, and a scan within Mythtv show 0% signal and no stations found. (Just to cover the obvious - yes it is plugged into a working ariel) I've also tried the device in Windows and the Hauppage software, when scanning, scans for a couple of seconds then tells me there's no signal. Is this a firmware / driver issue, or have I bought a duff Wintv box..? Many thanks in advance for your help (this forum has been invaluable in getting me this far) and apologies for the lengthy post. Dan _______________________________________________ pvrusb2 mailing list [email protected] http://www.isely.net/cgi-bin/mailman/listinfo/pvrusb2
